| Content |
The OctaMic II provides 8-Channel 192 kHz / 24 bit AD conversion with eight hi-class microphone and line pre-amplification channels, featuring a combination of sophisticated components and approved RME technology.
Lowest distortion, excellent signal to noise ratio and perfectly linear frequency response transmit and amplify the microphone signals truly unchanged.
The OctaMic II includes some significant enhancements compared to the OctaMic:
The balanced TRS inputs of the Neutrik Combo XLR jacks are phantom power-free and can be operated as real line inputs too. The improved design of the input circuits allows for a maximum input level of +21 dBu with a convenient gain range from 6 dB up to 60 dB.
Improved signal to noise ratio (SNR) ADC 107.5 dB
Improved THD, especially at higher gains
Optimised heat dissipation by a new and larger housing with improved convection
Internal wide range power supply with line filter, insensitive to voltage fluctuations
Super-stable, short circuit proof 48 V phantom power
Features
OctaMic II offers 8 balanced XLR mic / line inputs via Neutrik XLR/TRS combo jacks. Each channel contains switches for 48V phantom power, a low cut filter and phase reversal. Amplification can be set between 6 and 60 dB. LEDs for signal, clip, and activated phantom power give a complete overview on the unit's status. When the special Clip Hold mode is activated, any detected clip-state will cause the corresponding LED to flash once per second. With this, the user gets a long-term peak detection, and no longer needs to constantly watch the LEDs. At the same time momentary overloads are still displayed correctly.
Frontside switches include power on/off and output level, for a choice of -10 dBV, +4 dBu or Hi Gain (+19 dBu) as reference level. This unusual feature offers two advantages. First, the reference level can be easily switched to match any of RME's current interface devices, from HDSP 9632 through Multiface up to the renowned ADI-8 series converters. Second, the Signal to Noise ratio is optimized, and the Clip-LED will exactly match the ones of the ADI-8 (2 dB below 0 dBFS).
The balanced line level output signal is available at the back of the unit via 8 stereo TRS jacks. The specially developed, internal hi-performance switch mode power supply lets the OctaMic II operate in the range of 100V to 240V AC. It is short-circuit-proof, has an integrated line-filter, is fully regulated against voltage fluctuations, and suppresses mains interference.
Top
AD-Conversion
The 8-Channel AD-conversion of the OctaMic II operates at up to 192 kHz. The digitized signal is available simultaneously at the double ADAT output (S/MUX, up to 96 kHz), and at a DB-25 connector (4 AES/EBU outputs, up to 192 kHz). The digital part can be clocked internally (master) and externally via word clock, AES/EBU and SPDIF.
RME's outstanding SteadyClock(TM) ensures perfect AD-conversion, as jitter on the external sync-sources is nearly completely removed. All settings are done via DIP-switches on the back of the OctaMic II. Analog outputs and both digital outputs operate fully simultaneously. The choice of reference level affects the analog outputs only, the signal/clip indication and the AD-conversion will react only to the Gain-pots.
Top
Tech Specs
8 balanced XLR/TRS mic/line inputs
54 dB gain range
Input impedance: XLR 2 kOhm, TRS 5 kOhm
Analog input level: from -40 dBu up to +21 dBu
Maximum output level: +21 dBu
Output impedance: 75 Ohm
Output level switchable Hi Gain / +4 dBu / -10 dBV
Signal to noise ratio (SNR): 129 dB EIN @ 150 Ohm
THD:
Large frequency range (200 kHz) with special EMI input filtering
Frequency response -0.5 dB: 5 Hz - 200 kHz
Hi-pass filter: 80 Hz, 18 dB/oct.
Line Out: 1/4" TRS (6.3 mm stereo jack), servo-balanced
Phantom power: +48 Volt switchable per channel
Internal wide range switching power supply 100-240 Volt AC
Unbeatable price/performance ratio!
AD conversion
SNR: >110 dB(A)
Supported sample rates: 28 kHz - 200 kHz
THD:
Sync Sources: AES/EBU (also SPDIF coaxial), wordclock, internal
SteadyClock(TM) ensures best sound quality even with jittery external clocks
Top
Accessories
Digital breakout cable Pro, AES/EBU, D-sub25 to 4x XLR-3 female + 4x XLR-3 male, 1m/3m/6m (ALVA Audio)
Digital D-sub cable, AES/EBU, D-sub25 male to D-Sub25 male, 1m/3m/6m (ALVA Audio)
Optical ADAT Toslink cable 1m/2m/3m/5m/10m (ALVA Audio)
Word Clock cable, 1 x BNC male to 1 x BNC male, 1m/5m/10m (ALVA Audio)
Top
Add-On
BOB-32 Universal Breakout Box with 2 x 8 XLR to 2 D-sub connectors (supports TASCAM and YAMAHA format), flip-frame case
|
The PRE-73 DLX is a one-channel vintage style microphone-, line- and instrument preamplifier. The signal path uses only discrete components like resistors, capacitors and transistors. The line and microphone input and the line output are transformer balanced, using three different transformers, each one optimized for its purpose.
This is the way audio components were built before integrated circuits became available. The subjective sound quality delivered by vintage equipment is often prefered over the one delivered by modern units, a situation that is even more obvious now when music is recorded with clean-sounding digital audio equipment.
The circuit used in the PRE-73 DLX is similar to the preamp section in the classical 1073 module with a corresponding sound character that is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres. The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.
FEATURES
- Vintage Style electronics. No intergrated circuits in the signal path.
- Maximum gain on the mic input is 80 dB, enough to handle passive ribbon mics with quiet sound sources.
- Gain range on the Line input: -20 to + 10 dB.
- Switchable impedance on the mic input, 1200 or 300 Ohms, will change the tone of most mics.
- Switchable phantom power and absolute phase.
- A high-impedance instrument input for any sound module, electric guitar or bass.
- A simple but effective 4-step LED output level meter.
- The output level controls makes it possible to make fine gain adjustments and also to overload the main gain stage(s) for more character and then lower the signal to a suitable level before the output stage.
- Combo XLR/TRS input jacks and separate output XLR and TRS jacks for flexible connections.
- Insert jack for inserting EQ´s and other units.
- External high power power supply to avoid interaction with the audio circuits and transformers.
- A solid build quality that will last many years of normal use.
The PRE-73 DLX has a number of improvement and new features compared to the PRE-73 MKII:
- Tantalum capacitors in the signal path.
- Selectable 1073-style high pass filter, 50Hz, 80Hz, 160Hz and 300Hz.
- Output Attenuator -7, -14, -21 and -28 dB (located after the output transformer) allows overdriving the output stage and the output transformer for added character by lowering the output signal to a suitable level.
- The circuit board is prepared for Carnhill Mic and Line transformer and high pass inductor.
- The Insert jack can be switched in/out from the front panel. An internal jumper can select that the Insert jack always has an output signal.
- Switchable 600 ohm Output Termination and Ground Lift on the back panel.
- Selectable Active or Passive DI input and selectable input impedance in active mode, Hi Z or 100 kohm, by internal jumpers.
- The DI can signal can be selected to pass or bypass the mic input transformer by internal jumpers.
- Relays are used to control internal switching for DI input, Phantom power, Mic Low Z, Insert and Phase for shorter circuit board signal paths. The relays are controlled by front panel switches.
- Revised gain switch for added headroom.
- Circuit board star grounding scheme.
- Revised power supply with separate regulators for the audio circuits and relay and LED circuits.
|
Applications
Console input extending for both Digital and Analog mixing
consoles in Studio, Live and Broadcast
Mic Pre-amps for ADAT/ Hard Disk/ Multitrack Recording
Innovation
If you love your compact Digital (or Analog) mixing console, but wish it had
more microphone inputs, ARX has the solution ? the 8 Pre: eight channels
of superb sounding Microphone Pre-amps in a compact 1 RU chassis.
The 8 Pre is the ideal console extender for those times when you need more
microphone inputs. Now you can put those unused line inputs to good use,
and who knows - the 8 Pre pre-amps sound so good that you?ll probably end
up using them all the time instead of the ones that came with your mixer!
Superb Audio Quality
The 8 Pre?s ultra low noise figures come from extensive use of premium
components plus care and attention to board design and layout. The result is
superb, transparent audio quality and the headroom to handle anything that a
mic can throw at it.
Gain is adjustable from 20 db through to 60 dB via a trim control on the front
panel, plus we?ve included a ?20dB Pad switch to tame the hottest condenser
mic output if required. The Clip status LED lights up 1 dB before the onset of
clipping, just to warn you you?re getting close.Phantom power is switchable in
banks of four channels: 1 through 4, 5 through 8. A Phase reverse switch is also
provided on each pre-amp channel to eliminate any close miking problems.
In short, the ARX 8 Pre is the mic Pre-amp that you?ll wish the console manufacturer
had used. It provides a unique solution to today?s multiple Mic Pre-amp requirements.
T E C H N I C A L S P E C I F I C A T I O N S
Input Gain 20dB to 60dB
Input Pad ?20dB
Input Impedance 4 KOhm
Input Headroom +23dB
Output Impedance 300 Ohm
Output Level (Max) +23dB
Frequency Response 20Hz ? 20KHz ±0.2 dB
Signal to Noise ratio (Gain set @ 20 dB)
?93dB Unweighted, ?99dB ?A? weighted
Distortion @ Unity Gain .004%, 20 Hz ? 10 KHz
Dynamic Range 116 dB
Phantom Power 48 VDC
Input Connectors Balanced XLR
Output Connectors Balanced TRS jack
Clip Indicator Illuminates 1 dB prior to clipping
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm |
Having had great success with the PRE-73 preamp, we have received many requests for a version for the 500 eries rack format. We are therefore happy to present the PRE-573, expected to start shipping in late September.
The PRE-573 is a one width module that has the sound and the features that made the PRE-73 so successful and a few additional ones.
The circuit still uses the preamp and output section from the classic 1073-module, adapted to work in the api rack format. It has a total gain range from -15 to +80 dB. The 10 - 70 dB range is handled by a turn switch and there is a separate toggle switch to select an additional 5 or 10 dB gain. The input can be configured to accept line level signals by another switch, the gain is then lowered by about 25 dB and the input impedance increased to about 15 kohm.
The input impedance of the mic input mode can be switched between 1200 and 300 ohm. Phantom power and phase reverse is also selectable by front panel switches.
An added feature, using the same circuit as in the PRE-73 DLX, is the active DI-input with a high input impedance of about 1,5 Mohm. The output signal from the active DI circuit passes through the input transformer for some extra character.
The DI-input is very flexible since it can be changed to a purely passive one by a front panel switch. The DI input is then exactly the same as in the PRE-73 Mk2 where the signal is feed directly into the second gain stage, bypassing the transformer and with an input impedance of about 100 kohm.
These two DI-options makes it possible to get different tones from electric instruments and the passive DI input mode is more suited for injecting active units like sound modules.
A new feature is the switchable AIR mode that adds a small boost above 10 kHz that peaks at 2 dB at about 35 kHz.
A simple but effective signal and overload indicator is offered by a single LED that starts glowing red at about +4 dBu and then increases its intensity up to the maximum output level.
The PRE-573 has a dedicated insert connector at the back allowing it to interface with other GAP 500 modules. The insert can be activated by removing a jumper connector at the back of the module.
The second Golden Age Project module for the api 500 rack will be the EQ-573, expected to ship in November 2012. The EQ-573 consists of the inductor based high pass filter section and the 3-band eq section from the classic 1073 module with some added frequencies. These two modules together will offer a fully fledged 1073-module in a compact format at a very low cost.
There is a second jumper at the back of the module that selects 600 ohm termination on the output. The standard mode is termination on, since it gives the flattest response when the PRE-573 is used with modern line inputs that typically has an input impedance of 10 kohm or more. The user can chose to remove the jumper and deactivate the termination resistor, this will increase the level above 10 kHz and create a peak in the response for an even more pronounced "Air" effect.
The output is transformer balanced and fully floating and can drive a 600 ohm load up to level of about 28 dBu.
|
PreSonusʼ popular Class A XMAX preamps are widely lauded for their clarity and transparency. Our tube preamps are beloved for their warm, smooth sound. With the Blue Tube DP V2 dual-path mic/instrument preamp, you get both types of high-quality sound in one unit.
Now weʼve improved on the classic unit with the BlueTube DP V2. The solid-state path now feeds PreSonusʼ top-of-the-line Class A XMAX™ mic preamplifier with 80 dB of variable gain—an upgrade from the original BlueTube DPʼs solid-state stage.
You still get all the secondary features you expect in a professional-grade preamp: 48V phantom power, an 80 Hz high-pass filter, -20 dB pad to control hot input signals, and a polarity-reverse switch. Each channel has an illuminated VU meter so you can visually monitor your input levels.
A Tube Drive control provides a wide range of sounds: when itʼs clicked off, youʼre using the solid-state preamp for quiet, transparent amplification; when itʼs engaged, your signals flow through the tube preamp, and you can achieve anything from gentle warmth to edgy distortion.
2 input channels, each with:
High-headroom Class A XMAX™ mic preamplifier with 80 dB gain range
12AX7 vacuum tube gain stage
Tube Drive tube-saturation control
48V phantom power
80 Hz high-pass filter
-20 dB pad to reduce hot input levels
Polarity-reverse switch
Illuminated analog VU input-level meter
Input/Output
2 balanced combo mic/unbalanced instrument inputs
2 balanced XLR main (L/R) line outputs
2 unbalanced ¼” main (L/R) line outputs
Physical
Compact 1/2U chassis
External 12 VDC, 1A power supply
|
The AD2022 is Avalon's fourth generation of fully discrete, symmetrical Pure
Class A microphone preamplifiers. The dual mono AD2022 includes the original
sonic capabilities and transparency of the M2, M22 and M5 preamplifiers plus
several additional features, including selectable microphone source loading for
optimized cable/mic matching, improved high-voltage Class A regulated power
supplies, two high Z instrument inputs, variable-passive high pass filter, teflon/
silver wiring and doubled plated circuit boards for superior low level signal transfer.
AD2022 FEATURES
Symmetrical Pure Class A design, two channels
Microphone and hi-Z instrument inputs
Gain switched 4dB steps plus +/- 3dB fine output trim
Selectable microphone input impedance matching
Low noise -126dB EIN
Ultra high quality, low-ratio, balanced input transformer
Balanced, high-current Class A output to +36dB
Large illuminated analog VU meters and twin peak LED's
Regulated phantom power supply +48v
Input polarity phase reverse
High headroom +36dB input before overload
Input -20dB pad for high level signals
Sealed silver relays for all signal routing
External AC 150w toroidal power chassis
Fully discrete Class A regulated audio power supplies
Deep, musical sound-stage, transparent amplification
MICROPHONE INPUT
The AD2022 incorporates the most advanced high-performance microphone
transformer available. Split low-ratio primary windings are carefully combined
within a custom mu-metal core for extended smooth frequency response and
very low distortion. Sealer silver relays are used for minimal signal invasion.
The input signal selector, high pass filter, polarity-phase reverse, +48v power
and the 20dB input attenuator all utilize local sealed relay operation. A variable
passive high pass filter provides a minimum phase shift design while eliminating
low frequency rumble, wind noise and mechanical vibration at sub sonic frequencies.
SYMMETRICAL PURE CLASS A DESIGN
Two 100% discrete, high-voltage, symmetrical Pure Class A signal amplifiers
are utilized per channel. The first operates in a cascaded-cascode FET
configuration while the second stage amplifier is fully bipolar. The twin amplifiers
share the total available gain requirement. This shared architecture increases
the high level headroom capability, improves transient response and doubles the
internal bandwidth of the ultra-high performance pure Class A signal amplifiers.
OUTPUT and METERING
High-current DC coupled, Class A discrete amplifiers are utilized for the output
drive interface with +36dB capability into all known loads. Two large, high-quality
analog VU meters indicate accurate signal readings while bi-color LED's offers
peak indication at 0dB and +20dB.
AD2022 PREAMPLIFIER SPECIFICATIONS
Circuit Topology: Twin cascode FET and bipolar low level signal amplifiers,
high-voltage, 100% discrete, symmetrical Pure Class A
Input Type and Load: Transformer balanced low-ratio, 50, 150, 600 and 1k5
ohm input load selection
Maximum Mic Level: +36dB balanced XLR pin 2 hot (with -20dB passive
attenuator)
Maximum Instrument Level +18dB at 100k ohms instrument input level,
standard mono 1/4 inch jack
Input Attenuator: -20dB resistive pre transformer primary, sealed silver relay
Phantom Power: +48v regulated 50mA capability, sealed silver relay
High Pass Filter: Passive, variable from 30Hz to 185Hz @ 6dB per octave,
sealed silver relay.
Polarity Reverse: Sealed silver relay on microphone input
Gain Range Input: +20dB to +64dB in 4dB steps
Gain Output Range: +/- 3dB variable conductive plastic potentiometer
Maximum Output Level: +36dB balanced 600 ohms, DC coupled, discrete
symmetrical Pure Class A
Output Type: XLR connector, pin 2 hot
Noise EIN Unweighted: -126dB 150 ohm
Noise 20kHz Unweighted: -102dB
Distortion THD, IMD: 0.05% nominal
Frequency Response -3dB: 1Hz to 120kHz transformer limit
System Bandwidth: DC to 1MHz
Output Meter: High quality, illuminated analog VU meter 0dB = +4dB.
Peak Meter: Bi-color LED's 0dB and +20dB peak detection circuit.
AC power supply B2T: External toroidal 100V to 240V, 50-60Hz selectable,
150 watts maximum.
Cables: 90V ac, 4 pin male power input connector, B2T required, internal
DC regulation
Dimensions: 19 x 12 x 3.5 in (482 x 305 x 89mm)
Weight: 15lbs (6.8kg)
Dimensions - Shipping Carton: 24 x 21.5 x 7.5 in (610 x 546 x 190mm)
Weight - Packed: 25lbs (11.4kg) |
Reviews
There are no reviews yet.