OMNITRONIC LH-053 PASSIVE DI BOX

22.94 incl. GR VAT

In stock (can be backordered)

EAN: 4026397218435
Installments calculation
CompareAdd to wishlist Submit Better Price
  • 1 high-impedance signal input, 6.3 mm jack
  • 1 low-impedance XLR output
  • 6.35 mm jack input, and output
  • Converts an unbalanced line input (e.g. instruments) into a balanced XLR output for connecting a mixer
  • Switchable input attenuation: 0 dB, -20 dB, -40 dB
  • Rugged black metal housing
  • 1 high-impedance signal input, 6.3 mm jack
  • 1 low-impedance XLR output
  • 6.35 mm jack input, and output
  • Converts an unbalanced line input (e.g. instruments) into a balanced XLR output for connecting a mixer
  • Switchable input attenuation: 0 dB, -20 dB, -40 dB
  • Rugged black metal housing

 

Read more

Little brother of the LH-055 DI Box. Sturdy housing, solid workmanship at an unbeatable price.

1-channel DI box, passive Converts unbalanced 6.3 mm jack line input (e.g. from instruments) into balanced XLR output for connecting a mixer Switchable input attenuation: 0 dB, -20 dB, -40 dB Ground-lift switch eliminates ground loop problems 1 signal input (6.3 mm jack) 1 parallel output (6.3 mm jack), feed-through of the input signal (e.g. to a guitar amplifier) 1 low-impedance output (XLR) Black housing

Passive 1-channel DI box, black

  • 1 high-impedance signal input, 6.3 mm jack
  • 1 low-impedance XLR output
  • 6.35 mm jack input, and output
  • Converts an unbalanced line input (e.g. instruments) into a balanced XLR output for connecting a mixer
  • Switchable input attenuation: 0 dB, -20 dB, -40 dB
  • Rugged black metal housing

Package contents

  • 1 x device, 1 x user manual
Frequency range: 15 – 30000 Hz
S/N ratio: >95 dB
Impedance: Input: 50 kOhm
Output: 600 Ohm
Input attenuation: 0 dB, -20 dB, -40 dB; switchable
Control elements: Groundlift selector
Connections: Input: 1 x 6.3 mm plug (unbal.)
Link: 1 x 6.3 mm plug (unbal.)
Output: line via 1 x 3-pin XLR
Dimensions: Width: 12,7 cm
Depth: 7,4 cm
Height: 4,5 cm
Weight: 440 g

 

Weight 0.70 kg

Reviews

There are no reviews yet.

Be the first to review “OMNITRONIC LH-053 PASSIVE DI BOX”

Your email address will not be published. Required fields are marked *

Quick Comparison

OMNITRONIC LH-053 PASSIVE DI BOX removeARX DI-PLUS 2 STEREO ACTIVE D.I BOX removeALPHATON DI 1000 TUBE D.I BOX removeBEHRINGER DI100 Ultra DI Box Active Battery/Phantom removeDBX DB-12 ACTIVE DI BOX WITH GROUND LIFT removeALPHATON SM-60 ACTIVE D.I BOX remove
NameOMNITRONIC LH-053 PASSIVE DI BOX removeARX DI-PLUS 2 STEREO ACTIVE D.I BOX removeALPHATON DI 1000 TUBE D.I BOX removeBEHRINGER DI100 Ultra DI Box Active Battery/Phantom removeDBX DB-12 ACTIVE DI BOX WITH GROUND LIFT removeALPHATON SM-60 ACTIVE D.I BOX remove
Image10355053 lh 053 di box balance unbalanceBEHRINGER DI100 Ultra-Rugged DI Box for Stage and Studio Powered active battery phantom
SKULH-053DI-PLUS 2DI 1000E005264DBX DB-12SM-60
Rating
Price 22.94 incl. GR VAT 203.11 incl. GR VAT 773.75 incl. GR VAT 46.00 incl. GR VAT 140.00 incl. GR VAT 113.09 incl. GR VAT
Stock

In stock (can be backordered)

In stock

In stock

In stock (can be backordered)

Available on backorder

In stock

AvailabilityIn stock (can be backordered)In stockIn stockIn stock (can be backordered)Available on backorderIn stock
Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
  • 1 high-impedance signal input, 6.3 mm jack
  • 1 low-impedance XLR output
  • 6.35 mm jack input, and output
  • Converts an unbalanced line input (e.g. instruments) into a balanced XLR output for connecting a mixer
  • Switchable input attenuation: 0 dB, -20 dB, -40 dB
  • Rugged black metal housing
  • Professional and multi-purpose direct injection box for stage and studio applications
  • Provides impedance and signal matching for the direct connection of instruments to mixers and amplifiers
  • Ultra-flat frequency response due to renowned BEHRINGER OT-1 transformer
  • Internal battery automatically shuts off when phantom power is applied
  • Allows direct connection to speaker outputs with up to 3,000 Watts
ContentLittle brother of the LH-055 DI Box. Sturdy housing, solid workmanship at an unbeatable price. 1-channel DI box, passive Converts unbalanced 6.3 mm jack line input (e.g. from instruments) into balanced XLR output for connecting a mixer Switchable input attenuation: 0 dB, -20 dB, -40 dB Ground-lift switch eliminates ground loop problems 1 signal input (6.3 mm jack) 1 parallel output (6.3 mm jack), feed-through of the input signal (e.g. to a guitar amplifier) 1 low-impedance output (XLR) Black housing

Passive 1-channel DI box, black

  • 1 high-impedance signal input, 6.3 mm jack
  • 1 low-impedance XLR output
  • 6.35 mm jack input, and output
  • Converts an unbalanced line input (e.g. instruments) into a balanced XLR output for connecting a mixer
  • Switchable input attenuation: 0 dB, -20 dB, -40 dB
  • Rugged black metal housing

Package contents

  • 1 x device, 1 x user manual
Frequency range: 15 - 30000 Hz
S/N ratio: >95 dB
Impedance: Input: 50 kOhm Output: 600 Ohm
Input attenuation: 0 dB, -20 dB, -40 dB; switchable
Control elements: Groundlift selector
Connections: Input: 1 x 6.3 mm plug (unbal.) Link: 1 x 6.3 mm plug (unbal.) Output: line via 1 x 3-pin XLR
Dimensions: Width: 12,7 cm Depth: 7,4 cm Height: 4,5 cm
Weight: 440 g
 

Phantom or battery powered in a rugged steel chassis
 
The ARX DI-PLUS 2 represents another major step forward in active direct boxes. Packaged in
a single channel stand-alone format, the DI-PLUS 2 represents a fresh look at active stereo
D.I. concepts.

Precision engineered
Ultra quiet, ultra clean circuitry delivers maximum headroom whatever the signal. Premium grade
components, plus an all-steel chassis gives excellent hum and noise specifications and superb
audio quality in a tough, roadworthy package. Accurate Left and Right channel level matching keeps
the stereo image centred.

Level control
The DI-PLUS 2 features two high impedance unbalanced inputs on the front panel, running to balanced
XLR outputs on the rear. A a global Pad switch drops inputs by 20dB, making it suitable for all applications
from the softest keyboard to the hottest broadcast levels.
 
Battery compartment
The revolutionary simple 'clamshell' action of the DI-PLUS 2 battery compartment makes battery changing
extremely easy, even on the darkest stages.
A 9v alkaline battery snaps into a PCB mounted battery holder for fast, secure location. No fragile battery clip
leads to break, no tools required, no screws to lose. Production crew heaven!
 
Automatic Phantom switching
The DI-PLUS 2 will automatically switch itself to the console's own Phantom Power, if available, and an LED
will indicate this mode. Turn the Phantom Power off and it will instantly revert back to battery mode.

Rugged all-steel case
A lot of direct boxes are fitted into brittle cast alloy cases. Not this one! The tough all-steel inner and outer
chassis of the DI-PLUS 2 provide excellent RF/EMF shielding while making it a sturdy, heavy duty unit that
is hard to dislodge, and hard to leave behind.
 
Rear panel showing Left and Right XLR connectors, ground lift switch, battery check switch and LED, plus
phantom power On LED and captive screw for opening up the unit for battery changing
 
Whether you're a Studio or Live Sound engineer, installation contractor, or broadcast engineer, you want all
the dynamics,clarity and stereo information of the original sound source transferred to the mixing console.
The ARX DI-PLUS 2 provides a rugged, no-compromise solution to all stereo direct injection and signal
balancing requirements.
 
T E C H N I C A L S P E C I F I C A T I O N S:
Max Input Level
+12 dB Phantom powered
+6 dB Battery powered
Input Impedance 1 Meg Ohm
Max Output Level
+17 dB 10K Ohm load Phantom powered
+12 dB 10K Ohm load Battery powered
+11 dB 600 Ohm load Phantom powered
+12 dB 600 Ohm load Battery powered
Output Impedance 680 Ohms Balanced
Output Signal to Noise
-100 dB unweighted
-104 dB A weighted
Dynamic Range
117 dB 10K Ohm load Phantom powered
112 dB 10K Ohm load Battery powered
111 dB 600 Ohm load Phantom powered
107.5 dB 600 Ohm load Battery powered
Distortion 100 Hz .0018%, 1KHz .0028%, 10KHz .0056%
Frequency Response 20Hz to 20KHz, ± 0.2 dB
Gain through Unit: 6dB (Pad switch out)
Pad Switch: Global -20 dB attenuation
Input and Loop Out Connectors
Insulated jacks (!!!Note that Channel A Input connector switches the unit on
when a plug is inserted. Remove plug when storing to avoid battery drain!!!)
Output Connectors
3 pin XLR. Wired Pin 1 Ground, Pin 2 + Hot, Pin 3 - Cold.
Global Audio Ground (Pin 1) lift switch
Construction
All-steel chassis, fibreglass PCB
Battery Access
Twist connector opens chassis, snap-in battery holder inside.
No tools required

Tube-buffered DI-Box DI-1000

The Tube-Buffered DI-Box DI-1000 allows the extraction of all the musical details of
musical interfaces without degrading the sound. This can only be achieved by
providing a very high input impedance to avoid any loading of instrument pickups.This
design approach allows seemingly infinite headroom to preserve the real dynamic range
of the interfaced instruments.A vacuum tube enables all these goals to be achieved
without any compromises in sound quality.The sonic difference between a standard
DI-Box and the Tube-Buffered DI-Box is comparable to the musical resolution difference
between a standard microphone and a studio microphone.One of the best transformers,
the very transparent sounding JENSEN JT-DB-E, was chosen providing complete ground
isolation. The parameters of this transformer, like frequency response, phase response,
group delay and geadroom capabilities, play a vital part in the performance of this DI-Box.
 
Technical Specifications
Input
The signal of the instrument is directly fed to the tube circuit with > 20 MOhms input
impedance to prevent any signal degradation, inevitable in traditional designs.
Buffered Output“
The second stage of the vacuum tube is used to buffer the signal and lower the output
impedance to < 8 kOhms. This unity gain output allows for cable runs of 10 meters
without loosing high frequency information.
Boost circuit
The boost circuit increases the signal send to the output transformer by 15 dB. This may
be useful for instruments with extremely low output, but decreases headroom capability
to 6 Volt rms. Under these circumstances the signal may be clipped, concerning the output
transformer?s signal, which gives you 2nd harmonic tube-like distortion. This distortion
normally does not occur - but is sometimes desirable, being the reason for this special feature.
Unity circuit
The unity circuit feeds a low distortion unity gain signal to the JENSEN output transformer.
This gives the best possible sound quality.
Ground-lift“-Switch
This front panel mounted switch allows complete ground and electrical isolation between the
direct injection box and the console or recording device.
 

Mechanical Specifications
Cabinet 2 mm stainless steel
Front- and rear-panel 1,5 mm stainless steel lasercut and photo-chemically etched
Dimensions 185 x 100 x 40 mm
Vibration insulation 4 high-compliance rubber-elements
Operating Voltage
220/110 V AC, selectable via rear panel mounted switch. The fuse is easily
accessible from the rear panel. IEC mains connector with optional fixture.
Construction details
Double sided glass fibre contacted PCB with 70 mm copper plating. 1% metal film resistors
and the finest polypropylene capacitors are used in the signal path. MIL type Switchcraft jacks
and high performance switches ensure flawless operation. The power supply is optimised via
measurement quality toroid transformer and a low impedance design to ensure the lowest
possible noise. Through a double sided PCB all parts are roadworthy secured. A waterclear
blue LED perfects the aesthetics of the DI box.

Technical Data
Input impedance > 20 MOhm
Output impedance180 Ohm at 1 kHz
Frequncy response 20 Hz - 20 kHz (-0,1 dB)
                             5 Hz - 120 kHz (-3 dB)
THD at 0 dBv  0,06% at 20 Hz
                      0,04% at 1 kHz
                      0,035% at 20 kHz
Signal to Noise Ratio 86 dB
Tube ECC 83/7025 A - military E 83 CC optional
Output transformer JENSEN JT-DB-E
Polarity Pin 2 Hot , AES/IEC -Standard
Max. Input voltage > 30 V peak
 

Product Features: Professional and multi-purpose direct injection box for stage and studio applications Provides impedance and signal matching for the direct connection of instruments to mixers and amplifiers Ultra-flat frequency response due to renowned BEHRINGER OT-1 transformer Internal battery automatically shuts off when phantom power is applied Allows direct connection to speaker outputs with up to 3,000 Watts Switchable input attenuation allows input levels of up to +50 dB Ground Lift switch eliminates typical ground loop problems ¼" TRS and gold-plated XLR connectors Ultra-rugged, road-suitable aluminum case Stackable oversized rubber corners High-quality components and exceptionally rugged construction ensure long life and durability Conceived and designed by BEHRINGER Germany   With the DI100, you can rest assured that your sound source will reach the console balanced and noise-free. BEHRINGER's take on the all-important active DI box gives you functionality, durability and incredible sound at a remarkable price.
Be Direct
Plug into the DI100's balanced 1/4" TRS or XLR input, then send a signal to your console via the balanced XLR output. You can even plug your guitar or bass amp's speaker output into the DI100, which can handle ratings of up to 3,000 Watts and still deliver a perfect signal. It also features a 1/4" LINK jack to send your signal to an on-stage amplifier. The DI100 also has a switchable attenuation pad, allowing input levels of up to +50 dB. There is also a ground lift switch to eliminate noise associated with ground loops. The DI100 also features BEHRINGER's renowned OT-1 output transformer.
Superior Sound, Incredible Value
DI boxes are an essential part of any stage or studio, and the DI100 delivers the exceptional sound you expect, wrapped up in a rugged, road-proof aluminum case with stackable rubber corners.

At dbx, when we do something, we do it right. So when we decided to create our new direct injection boxes, we didnʼt settle for the same old tired approach to direct box design. With our dbx name on the line, how could we? One look at our new dB10 Passive and dB12 Active direct boxes will tell you that these are clearly different. With their bullet-proof construction, and extraordinary audio performance to rival their looks, finally thereʼs a direct box worthy of the dbx name.

Utilizing custom dbx mu-metal-shielded audio transformers, high-quality Neutrik® connectors, and low-noise circuitry preserves the sonic integrity and true characteristics of the signal source. Both boxes include a pad switch that accomodates instrument, line and even speaker level signals. Take even more control of your sound by utilizing the polarity invert switch to set the phase relationship between the direct and mic'd sound.

As a professional, you donʼt have time for interference, so weʼve included a ground lift switch to solve potential hum and buzz problems due to ground loops. And between the combined shielding of the cast metal chassis and the custom-wound transformer, you can be doubly assured of a clean signal free from interference. All of this sits atop a solid, stable footprint, that will keep the box from being dragged around the stage, and the unique contoured underside allows secure stacking of multiple units.

So whether you need to control the level, placement in the mix, or overall characteristics of 4 independent signals or control the gain leveling on a couple of stereo pairs, the dbx dB12 is for you.

Features
  • Parallel 1/4" Thru Jack
  • Transformer Isolated
  • Premium Shielded Custom dbx Transformer
  • Balanced XLR Lo-Z Output
  • 3-Way 0/20/40 dB Pad Switch
  • Flat/High-Cut Filter Switch
  • Output Polarity Invert Switch
  • Ground Lift Switch
  • 4 Year Warranty!
  • Additional dB12 Features
    • Phantom Powered
    • Green LED Phantom Power Indicator
    • +48V Phantom Operation
    • Low-Noise Active Circuitr

    dB12 Specifications INPUT SECTION

    Input: 1 instrument/line/speaker level

    Connector: 1/4" jack

    Type: Unbalanced, RF filtered

    Impedance: 150k Ohm typical

    Max Input Level: +20dBu (0dB pad)
    +40dBu (20dB pad)
    +60dBu (40dB pad)

    OUTPUT SECTION

    Thru Output: 1 parallel connection from input jack

    Connector: 1/4" jack

    Type: Unbalanced, RF filtered

    Main Output: 1 line level

    Connector: XLR male jack

    Type: Balanced

    Impedance: 150 Ohm typical

    Max Output Level: 0dBu

    PERFORMANCE

    Transformer: Custom dbx mu-metal-shielded

    Frequency Response: 20Hz to 20kHz, +/-2.5dB

    Noise:

    THD:

    GENERAL

    Dimensions: 5.82" L X 5.44" W X 2.20" H (148 x 138 x 56mm)

    Weight: 1.4 lbs / 0.65 kg

    Note: Specifications subject to change without notice.

    Active DI-Box SM-60

    The electronic Direct-Injection Box SM-60 allows direct connection of electronic
    music instruments such as keyboards, synthesizers, electric and electronic pianos,
    etc. with mixing consoles in PA-systems and in recording studios.
    The SM-6 is designed for applications, where a passive DI-Box does not perfom
    satisfactorily, i.e., where the output level of a passive DI-Box is too low for the microphone
    input section of the mixing desk.
    Because the input impedance of the SM-6 is above 5 MOhm, instrument outputs are
    not loaded or in any other way adversely affected. The voltage ratio from input to output
    is 1: 1 and is always sufficient for connection with any microphone input. Input connectors
    are 1/4" phone jacks, output connector is a Switchcraft D3M; output is 600 Ohms,
    transformer balanced. The output level may in certain cases overload microphone inputs -
    the line input section of the mixing console must then be used for connecting the SM-6.
    The unit operates with a 9 V battery or phantom powering from 24 to 48 volts.

    Technical Data

    input impedance > 5 MOhm
    max. input impedance + 6 dBu, 1,55V
    ouptut impedance 600 Ohm
    frequency response 20 ... 20000 Hz, ± 0,2 dB
    gain 1 : 1
    THD < 1 % at 30 Hz
           < 0,7 % bei 40 Hz
    powering  9-V battery (IEC 6LF22) or
                     phantom power 24 ... 48 V.
    inputs  two 1/4" phone jacks , unbalanced
              (one being used as output to instruments amp)
    outputs  XLR, balanced
                 pin 1 = ground, pin 2 = hot, pin 3 = cold
    case aluminium die-cast
    weight 240 g
    dimensions 113 x 71 x 37 mm

    Weight0.70 kg0.60 kg0.60 kg0.65 kg1.00 kg0.24 kg
    DimensionsN/AN/AN/AN/AN/AN/A
    Additional information
    Weight 0.70 kg
    Weight 0.60 kg
    Weight 0.60 kg
    Weight 0.65 kg
    Weight 1.00 kg
    Weight 0.24 kg