Content |
The P2110-T is a weatherproof full range, wide-dispersion, coaxial two way loudspeaker system for small and medium size distributed systems.
The high frequency section is a constant directivity horn loaded to a 1” RCF Precision Neodymium compression driver with a 1.50” diaphragm assembly for smooth, wide dispersion. The low-frequency transducer is a 10” woofer with a 2.5” voice coil. The cabinet is equipped with 12 x M 8 brass inserts, a stainless steel U-Bracket and pair of spacers for 90° mounting.
The system features a selectable line transformer for 70 - 100 Volt applications/installations, it meets the requirements of IP 55 code (International Protection Rating)
Features |
---|
Cabinet is a single piece rotational moulded in medium density polyethylene, fully UV protected and waterproof IP 55 | Front grille in custom perforated aluminium with open-cell fibres and water repellent woven fabric backing | Stainless steel bracket | One 10" high-output LF transducer with 2" voice coil | One RCF Precision Neodymium 1" Compression Driver with 1.5" voice coil | 90° x 40° constant directivity horn | Built in passive crossover and selectable line transformer | 10° X 20° enclosure sides for array configurations | Active Mosfet Compression Driver Protection | LICC (Low Impedance Compensated Crossover) network |
12 brass suspension points (M8)
Acoustical Specifications |
---|
Frequency Response -10 dB: | 95 Hz | ÷ 20 kHz | Frequency Response -3 dB: | 120 Hz | ÷ 20 kHz | Max SPL @ 1m: | 118 dB | | Horizontal coverage angle: | 90° | | Vertical coverage angle: | 40° | | Directivity index; Q: | 11 | | System Sensitivity: | 95 dB | | Nominal Impedance: | 16 Ω | | Power Handling: | 200 Watt | | Peak Power Handling: | 800 Watt | | Recommended Amplifier: | 400 | | Protections: | Dinamyc | | Crossover frequencies: | 2000 Hz | |
TRANSDUCERS |
---|
Compression Driver: | 1.5" HF driver, 1" voice coil | | Nominal Impedence: | 8 Ω | | Input Power Rating: | 25 Watt AES | | Sensitivity: | 106 dB | | Woofer: | 10" woofer, 2.5" voice coil | | Nominal Impedence: | 16 Ω | | Input Power Rating: | 180 Watts AES | | Sensitivity: | 95 dB | |
INPUT SECTION |
---|
Input connector: | 5m, 4-adriges Neopren Kabel | | Constant voltage transformer: | 70/100 | | Power Selection: | 70V/30W ,15W , 100V/60W, 30W | |
CABINET |
---|
Cabinet Material: | Polyethylene rotomoulded | | Hardware: | 12 x M8 inserts+ U-brackets and pair of spacers | | Grille: | Custom perforated aluminium grille with open-cell fiber and water repellent woven fabric backing | | Colour: | Grey | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 350 / 13.78 mm/inch | | Width: | 350 / 13.78 mm/inch | | Depth: | 320 / 12.60 mm/inch | | Net Weight: | 13.5 / 29.75 Kg/Lbs |
|
|
- Sealed type speaker with 60W continuous pink noise and 180W continuous program power handling capacity.
- Highly efficient operation at rated sound pressure level of 96dB (1W, 1m).
- Frequency response of 100Hz~20,000Hz and 2.5kHz passive network crossover frequency.
- Two-way coaxial unit with 25cm low- frequency cone speaker and high- frequency CD horn fitted with compression driver (60º horizontal × 60º vertical).
- 1.6mm thick punching net and coniferous plywood enclosure make the speaker especially well-suited for indoor sports facility applications.
- Black, semi-matte urethane-painted coniferous plywood enclosure and black, semi-matte acryl-painted steel plate grille.
- Speaker mounting brackets and speaker mounting bolts included.
- Optional matching MT-S0601 transformer.
Spec. | Enclosure | Sealed type | Power Handling Capacity | Continuous Pink Noise: 60W/Continuous Program: 180W | Rated Impedance | 8 ohms | Sound Pressure Level | 96dB (1W, 1m) | Frequency Response | 100 - 20,000Hz | Crossover Frequency | 2.5kHz (passive network) | Speaker Component | 2-way coaxial unit/Low Frequency; 25cm cone speaker
High Frequency; CD horn fitted with compression driver (60º horizontal × 60º vertical) | Input Terminal | 2-pole M5 screw terminal, pitch between barriers; 12.2mm | Finish | Enclosure; Coniferous plywood, black, semi-mat, urethane paint
Grille; Steel plate, black, semi-mat, acryl paint | Dimensions (W × H × D) | 460 × 310 × 200mm | Weight | Speaker System; 9kg
Mounting Bracket; 2kg | Accessories | Speaker mounting bracket × 2
Speaker mounting bolt × 4 | |
- Passive 2-way bass-reflex installation speaker
- 200 W permanent load capacity
- 118 dB maximum sound-level pressure
- 10" custom woofer and 1" Celestion high-frequency driver
- Rotating CD horn with 80° x 60° dispersion
- For vertical or horizontal use
- speakON-compatible and terminal block input
- 4 x M8 mounting holes
- Shock-resistant front grille for optimum speaker protection
- Extensive range of smart accessories for installation
- Available in black or white
With its streamlined and compact design, the LD Systems SAT 102 G2 is excellently suited for permanent installation and discreet integration into virtually any setting. It features a 10" custom woofer and a 1" compression driver from Celestion, connected to a rotating CD horn with 80° x 60° dispersion. This makes the passive 2-way speaker ideal for both vertical and horizontal use.
The SAT 102 G2 attains a maximum sound-level pressure of 118 dB over a frequency response curve of 65–19 kHz with a permanent load capacity of 200 watts. The reflex casing made of 15 mm MDF has four M8 mounting holes. The inputs are a speakON-compatible socket and a terminal block, while an additional terminal block serves as an output for convenient parallel connection.
Special wall holders are available as an accessory to facilitate wall mounting. The SAT 102 G2 is available in black (Art. No. LDSAT262G2) or white textured finish (Art. No. LDSAT262G2W).
Product type
Installation Loudspeakers
Type
Wall-mounted Loudspeaker
Low/mid driver dimensions
10 "
Woofer size
254 mm
Woofer magnet
Ferrite
Woofer brand
Custom-made
Woofer voice coil (mm)
50.8 mm
Horn
CD horn
HF driver dimensions
1 "
HF Driver Size
25.4 mm
HF driver magnet
Ferrite
HF driver brand
Celestion
HF driver voice coil
1 "
HF Driver Voice Coil
25.4 mm
Dispersion (H x V)
80 x 60 °
Load rating (RMS)
200 W
Peak power
400 W
Frequency response
65 - 19000 Hz
SPL (1W/1m)
95 dB
Max. SPL
118 dB
Impedance
8 Ohm(s)
Protection circuits
HF Driver
Loudspeaker inputs
2
Speaker input connections
Speakon compatible , terminal block
Loudspeaker outputs
1
Speaker output connections
terminal block
Cabinet material
15 mm MDF
Cabinet surface
texture paint
Cabinet colour
Black
Cabinet construction
vented
Width
300 mm
Height
550 mm
Depth
270 mm
Weight
12,2 kg | MASTER AUDIO SB250 Passive Loudspeaker 2 Way 10" 200Wrms 8 Ohm
- 2-way passive speaker box
- Impedance(Ohm) 8
- Power output 200 W RMS
- ABS box - Woofer 10“, paper cone
- Compression driver,1" titanium diaphragm
- Frequency reponse: 50 - 17KHz (-10dB)
- Sensitivity: 103 dB - Speakon input and output
- Dimension: 472 x 345 x 270 mm
|
Features
Hard-suspension bass with Kapton spool
High-range horn with thermal overload protection
Integrated high-quality frequency cross-over (not for RSP-18 S)
Sound characteristics geared especially to heavy-bass sounds like hip hop, techno, house & breaks
High-performance reserves
Extremely durable, road-compatible carpeting
Protective metal corners
Large carrying shells made of metal
Sunk-in metal flange for tripods (not RSP-12 M and RSP-30)
Robust front grid
Connections via PA pro speaker cable and 6.3 mm jack
Technical Data
100 watt RMS PA-speaker
Max. capacity: 200 watt
Type: 2-way system
Frequency range: 45 Hz - 20 kHz
Acoustic pressure: 97 dB
Speaker: 25 cm (10“) woofer, mid-range and tweeter
Impedance: 8 ohm
Dimensions: 530 x 375 x 340 mm
Weight: 11.5 kg
| This highly professional 2-way loudspeaker is designed for absolute, long-term reliability. With its multifunctional bass reflex cabinet as a full range speaker, satellite and ground monitor, it is suited to mobile and fixed PA systems. The Stinger® 10 G3 provides 300 watts of continuous power; the maximum sound pressure level is 120 dB. Its specially developed 10" woofer and the BMS HF driver achieve a powerful bass reproduction and fresh natural highs. The wave guide of the tweeter has been developed using the Boundary Element Method (BEM), a numerical simulation of the sound radiation and dispersion. It reduces reflections from the floor and ceiling and prevents sidelobe levels and thus achieves a controlled and homogeneous dispersion. The Stinger® 10 G3 is designed as a real all-round workhorse. The cabinet is made from robust birch plywood and offers exceptional stability and durability thanks to its extremely durable polyurea coating. The features include a steel grille, a Dual-Tilt stand attachment, flight points and ergonomic handles. The Stinger® 10 G3 is an affordable solution for professional PA applications; extensive accessories support the use on stage and in fixed installations.
Product type
PA loudspeaker
Low/mid driver dimensions
10 "
Woofer voice coil (mm)
50.8 mm
Horn
BEM optimized CD Horn
HF driver voice coil
25.4 mm
Dispersion (H x V)
90 x 50
Frequency response
65 - 20000 Hz
Protection circuits
HF Driver
Speaker input connections
Speakon compatible
Speaker output connections
Speakon compatible
Speakers per amplifier channel (DSP44/45K)
4
Cabinet material
12 mm Plywood
Cabinet construction
Bass Reflex
|
Reviews
There are no reviews yet.