| Content | With the PAN05, two microphone signals can be mixed down to one. Since decoupling occurs via the balanced resistor network, the PAN05 also lets phantom power "pass through“, useful for condenser microphones. However, due to the difference in sound and signal level, mixing dynamic and condenser mics should be avoided. Best results will be achieved using two identical mics.
SPECIFICATIONS:
- Input: 2 x XLR/f balanced
- Nominal impedance: 200 Ω
- Output 1 x XLR/m balanced
- Load impedance >200 Ω
- Symmetrically decoupled through resistors
- Total ohmic value: 200 ohms
- Typical attenuation: 6 dB
- Housing: metal casing 110 x 73 x 42 mm
|
The dbx CT3 is an advanced cable testing unit allowing you to evaluate a large variety of cables with ease. The CT3 offers many common connectors such as RJ45, RJ11, MIDI, Speaker Twist, XLR, RCA Phono, BNC, DIN, TRS, TS, DMX, & Banana. It can be split into 2 parts, a SENDER and RECEIVER so preinstalled and long cables can be tested.
Features
- Tests up to 8-pin cables
- 2 piece chassis for testing installed cables
- Test Tone Generator
- Allows connection between different format connectors with ease
- ʽBananaʼ connector continuity tester with beeper and LED indicator
- Super-rugged construction for durability and longer life
- (2) DMX (5-pin) connectors for testing of 5 pin->to pin connections
- (2) BNC connectors for testing of 2 pin->to pin connections
- (2) RCA Phono connectors for testing of 2 pin->to pin connections
- (2) XLR connectors (1 x Male, 1 x Female) for testing of 3 pin->to pin connections
- (2) MIDI (5-pin DIN) connectors for testing of 5 pin->to pin connections
- (2) Speaker Twist connectors for testing of 4 pin->to pin connections
- (2) Banana connectors for testing of 1 pin->to pin connections
- (2) 1/4” (6.3mm) TRS/TS connectors for testing of 3 pin->to pin connections
- (2) RJ45 connectors for testing of 8P8C modular connections
- (2) 1/8” (3.5mm) TRS/TS connectors for testing of 3 pin->to pin connections
Specifications | Power Requirements | (2) 9V batteries, one per side (Batteries not included) | | Dimensions | 3.5” (8.9cm) (W) x 5.5” (14cm) (L) x 1.5” (3.7cm) (H) |
|
Digilyzer? DL1
Digital audio analyzer / audio meter with integrated speaker, audio lens and a
comprehensive event logger. Digital audio becomes simple by using the Digilyzer DL1.
The digital audio meter Digilyzer DL1 provides a comprehensive set of analysis
functions for digital, audio and video related audio signals.
It handles virtually all digital audio formats including ADAT and sampling frequencies
up to 96 kHz. The simple and intuitive operation allows the user to monitor, analyze
and troubleshoot any digital signals.
Debugging of digital audio signals becames easy with the assistance of the Digilyzer:
Features like the integrity check, the integrated speaker with audio lens function, the
logging functions, the ?over all? view of all important parameters and many more functions
to allow you to understand whats going on and finding faults easier than ever.
The Digilyzer is a handheld, battery powered device with optional mains power supply and
optional USB interface called MiniLINK.
MiniLINK, the USB interface for the Digilyzer allows documentation and data acquisition of
all DL1 functions in conjunction with the easy to use MiniLINK PC application. MiniLINK
supports online data logging up to several days. Read more about MiniLINK.
Product-details
? AES3, S/PDIF, TOS-Link
? ADAT Interface
? Sampling Frequency 32-96 kHz
? Digital Audio Analysis
? Carrier Status Analysis
? Carrier Signal Measurement
? Dual Domain Monitor Speaker
? Comprehensive Event Logger
| Digital Sound 8928 SPL Meter with Built-In Measurement Mic - calibrated from 300Hz to 8kHz (+/-2dB), 4 control zones in 10dB steps (40-130dB), large LCD display, peak-hold, fast/slow display modes, includes 9V battery.
A superbly designed easy to use sound level meter with features normally only found on more expensive instruments. It has an electret condenser microphone giving virtually instant readings updated every 0.5 seconds on an extra large LCD display.
- 4 measuring ranges, 40 to 70dB, 60 to 90dB, 80 to 110dB or 100 to 130dB
- 0.1dB resolution updated every 0.5 seconds
- Auto ranging or manual range selection
- ʽAʼ & ʽCʼ frequency weighting
- Fast or slow response filters
- 42mm LCD display with quasi-analogue bargraph and function Indicators
- Bargraph in 1dB steps updated every 40ms
- Max hold function to display the highest recorded value
- Min/max memory since power on or last reset
- Low battery indicator
- Auto power off
- Analogue output AC: 0.707 Vrms (at full scale)
- Supplied with battery
| This is an on-the-road tool you certainly can't miss in your gearbox! A nifty, handy cabletester, which allows you to check up to six (welding) connections and gives you a visual readout by 2 rows of 6 LED's. The checking itself is done manually per connected pin. A LED will light up to indicate what pin is connected correctly on which side. A short-circuit check with a red LED and audio-warningsignal is also included. On the left and right side you'll find inputs for 6,3 symm. jack, BNC, RCA, 5p. DIN, 5p. XLR, 3p. XLR and Neutrik® Speakon®.
We all know how frustrating and time consuming it can be when your audio cables fail. With the dbx CT2 cable testing unit you can now evaluate a large variety of your cables with ease. The CT2 offers many common connectors such as Speaker Twist, XLR, Phono, BNC, DIN, TRS, TS, DMX, & Banana. The CT2 allows for testing cables even with different connectors at each end. For example, it is simple to test a TRS to XLR cable. With well illuminated LED indicators and a simple rotary dial, users can quickly establish whether a cable is wired and functioning correctly, or if it is dead and in need of repair.
Features
- 6-position rotary selector with individual LEDʼs for up to five pins plus internal battery life check
- ʽBananaʼ connector continuity tester with beeper and LED indicator
- Super-rugged construction for durability and longer life
- (2) Speaker Twist connectors for testing of 4 pin->to pin connections
- (2) XLR connectors (1 x Male, 1 x Female) for testing of 3 pin->to pin connections
- (2) RCA Phono connectors for testing of 2 pin->to pin connections
- (2) BNC connectors for testing of 2 pin->to pin connections
- (2) MIDI (5-pin DIN) connectors for testing of 5 pin->to pin connections
- (2) DMX (5-pin) connectors for testing of 5 pin->to pin connections
- (2) 1/4” TRS connectors for testing of 3 pin->to pin connections
- (2) Banana connectors for testing of 1 pin->to pin connections
Specifications
| Power Requirements |
9V battery (Battery not included) |
| Dimensions |
3.5” (8.9cm) (W) x 5.5” (14cm) (L) x 1.5” (3.7cm) (H) |
|
ARTSOUND A8862 LASERGRIP THERMOMETER
Temperature range: -32 C - 550 C
Accuracy: 1,5%
Power supply: 9V
Weight: 258gr
|
Reviews
There are no reviews yet.