PALMER AUDIO DACCAPO Reamping Box Re-Amplification

Discontinued

75.73 incl. GR VAT

Out of stock

CompareAdd to wishlist Submit Better Price
  • Play back a recorded guitar signal
  • Send your signal to an amplifier where it’s picked up by microphones and recorded again
  • The recording engineer can experiment with the sound of an instrument
  • Takes care of all impedance matching issues
  • Also eliminates ground loop humming
  • Play back a recorded guitar signal
  • Send your signal to an amplifier where it’s picked up by microphones and recorded again
  • The recording engineer can experiment with the sound of an instrument
  • Takes care of all impedance matching issues
  • Also eliminates ground loop humming

 

Read more

A Reamping-Box is mainly used in studios. It allows you to play back a recorded guitar signal and send it to a guitar amp, where it can again be taken and recorded by the microphone. This allows the sound engineer to take time to experiment with the sound of the instrument using different amplifiers.

The DACCAPO box ensures optimal impedance matching and eliminates ground loop hum through the use of a transformer. The signal level to the amplifier can be adjusted with a volume control.

Product type

Product type
DI Boxes
Channels
1
Inputs
1
Input connectors
XLR
Max. input level
+22 dBu
Input impedance
600 Ohm(s)
Outputs
1
Output connectors
6.3 mm jack
Max. output level
+ 22 dBu
Output impedance
100 k Ohm(s)
Frequency response
20 – 20000 Hz
Transformer balanced
Yes
Ratio
Variabel
Controls
Gain
Cabinet material
sheet steel
Cabinet surface
Powder coated
Width
125 mm
Depth
80 mm
Height
45 mm
Weight
0,494 kg

 

Weight 0.29 kg

Reviews

There are no reviews yet.

Be the first to review “PALMER AUDIO DACCAPO Reamping Box Re-Amplification”

Your email address will not be published. Required fields are marked *

Quick Comparison

PALMER AUDIO DACCAPO Reamping Box Re-Amplification removeOMNITRONIC LH-055 PASSIVE DI BOX removeDOD AC 275 Active Direct Box with Switchable Ground Lift and Attenuator-2nd Hand- removePALMER AUDIO PAN01 Passive DI-box removeOMNITRONIC LH-060 2-channel DI box/splitter, passive removeSTEWART ADB1 ACTIVE D.I BOX remove
NamePALMER AUDIO DACCAPO Reamping Box Re-Amplification removeOMNITRONIC LH-055 PASSIVE DI BOX removeDOD AC 275 Active Direct Box with Switchable Ground Lift and Attenuator-2nd Hand- removePALMER AUDIO PAN01 Passive DI-box removeOMNITRONIC LH-060 2-channel DI box/splitter, passive removeSTEWART ADB1 ACTIVE D.I BOX remove
Image
SKUPDACCAPOLH055275PAN01LH060ADB1E
Rating
Price 75.73 incl. GR VAT 43.00 incl. GR VAT 73.93 incl. GR VAT 52.07 incl. GR VAT 73.35 incl. GR VAT 164.56 incl. GR VAT
Stock

Out of stock

In stock

In stock

Only 5 left in stock (can be backordered)

Available on backorder

Available on backorder

AvailabilityOut of stockIn stockIn stockOnly 5 left in stock (can be backordered)Available on backorderAvailable on backorder
Add to cart

Read more

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
  • Play back a recorded guitar signal
  • Send your signal to an amplifier where it's picked up by microphones and recorded again
  • The recording engineer can experiment with the sound of an instrument
  • Takes care of all impedance matching issues
  • Also eliminates ground loop humming
ContentA Reamping-Box is mainly used in studios. It allows you to play back a recorded guitar signal and send it to a guitar amp, where it can again be taken and recorded by the microphone. This allows the sound engineer to take time to experiment with the sound of the instrument using different amplifiers. The DACCAPO box ensures optimal impedance matching and eliminates ground loop hum through the use of a transformer. The signal level to the amplifier can be adjusted with a volume control. Product type
Product type
DI Boxes
Channels
1
Inputs
1
Input connectors
XLR
Max. input level
+22 dBu
Input impedance
600 Ohm(s)
Outputs
1
Output connectors
6.3 mm jack
Max. output level
+ 22 dBu
Output impedance
100 k Ohm(s)
Frequency response
20 - 20000 Hz
Transformer balanced
Yes
Ratio
Variabel
Controls
Gain
Cabinet material
sheet steel
Cabinet surface
Powder coated
Width
125 mm
Depth
80 mm
Height
45 mm
Weight
0,494 kg
 

 1-channel DI box, passive Converts unbalanced 6.3 mm jack line input (e.g. from instruments) into balanced XLR output for connecting a mixer Switchable input attenuation: 0 dB, -20 dB, -40 dB Ground-lift switch eliminates ground loop problems 1 signal input (6.3 mm jack) 1 parallel output (6.3 mm jack), feed-through of the input signal 1 low-impedance output (XLR) Gray housing

DOD AC 275 Active Direct Box with Switchable Ground Lift and Attenuator-2nd Hand-

The AC 275 is an active, phantom powered direct box. Unlike a passive DI where the frequency response of the signal can be altered depending on the connected impedance, an active DI buffers the input signal with an amplifier. This assures that the sound source will reach the mixer balanced and noise-free.

Housed in a cast alloy chassis, the AC 275 supplies two, high impedance, unbalanced 1/4" jacks and one low impedance balanced XLR jack. It operates with battery or phantom power.


Key Features
?

Active direct box

?

Allows a hi impedance unbalanced source to directly feed a low impedance balanced input

?

Flat frequency response

?

Connects guitar pickups, microphones or electric instruments to a recording or P.A. console without audio quality loss

?

Internal pad for speaker level input

?

Operates with battery or phantom power

?

Ground lift switch eliminates typical ground loop problems

?

Rugged, road-proof cast alloy chassis

Passive DI box. Jack input with paralell "THRU" output, transformer balanced XLR output. Attenuable input sensitivity, can handle both line level and speaker level signals.

Product type DI Boxes
Type passive
Channels 1
Inputs 1
Input connectors 6.3 mm Jack
Max. input level + 54 dBu
Input impedance (@ 60 Hz) 60k Ohm(s)
Input pad 0 / -30 dB
Outputs 1
THRU outputs/channel 1
Output connectors 6.3 mm Jack , XLR
Max. output level + 4 dBu
Output impedance 600 Ohm(s)
Frequency response 20 - 20000 Hz
Transformer balanced yes
Ratio 10 : 1
Controls attenuator , ground lift
Cabinet material sheet steel
Cabinet surface powder coated
Width 110 mm
Depth 73 mm
Height 42 mm
Weight 0,34 kg

 

2-channel DI box/splitter, passive Converts 2 separate unbalanced line inputs (e.g. instruments) into 2 balanced XLR outputs for connecting a mixer Switchable to split mode (input 1 routes the signal to both outputs) Switchable input attenuation: 0 dB, -20 dB, -40 dB Ground-lift switch eliminates ground loop problems 2 signal inputs via XLR/jack combo connectors 2 low-impedance XLR outputs Modern convex housing design Full rubber housing corners for safe operation Cables can be routed under the housing

The Stewart ADB-1 is a single channel active direct box that allows an unbalanced source to
directly feed a balanced input. Musical instruments, tape recorders, VCRs and sound projectors
can be run "direct" to the mixing console, avoiding unnecessary degradation of sound quality.
The ADB-1 operates on either phantom power or a 9-volt battery.

FEATURES:
Flat response
Low distortion
Low noise
Wide dynamic range
No transformer
RF protection on input and output
Switchable ground isolation
Flush mounted slide switches

Weight0.29 kg0.70 kg2.50 kg0.34 kg0.70 kg0.50 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 0.29 kg
Weight 0.70 kg
Weight 2.50 kg
Weight 0.34 kg
Weight 0.70 kg
Weight 0.50 kg