Content |
- Latency-free analogue signal path
- Customisable
- Level indicator L/R with +4, +10 and +18 dBu calibration options
- Correlation meter for verifying mono-compatibility
- Two headphone outputs with volume controllers and main cue selector switches
- Three analogue inputs, one S/PDIF input
- Three loudspeaker outputs with volume controllers for level calibration
- Mono summed output for subwoofer or mono monitor
- Main and cue direct outputs
Switching between different signal sources and monitors is one of the most common tasks in any studio. Ergonomic console design and two clearly structured control levels makes the Palmer MONICON XL the perfect, intuitive nerve centre for all your requirements. Selecting audio sources and loudspeakers is convenient and at the touch of a button.
The Palmer studio monitor controller features three analog stereo inputs, one S/PDIF input and outputs for three monitor pairs, each with its own volume controller for level calibration. A further mono summed full-range output is also available for connecting either a mono monitor or a subwoofer. An exclusive highlight of the MONICON XL is its correlation meter, which displays the phase difference between a stereo signal\'s left and right channels. This facilitates the quick and simple discovery of mono-compatibility errors in mixes. The controller is also customisable to your personal work style.
Its fully analogue audio circuit means that the MONICON XL demonstrates absolutely no latency or signal distortion. Additional features that are a must for any studio make the device far more than simply a monitor controller. Two headphone outputs with volume controllers and main cue selector switches, a cue master controller and an on/off talkback microphone with volume control are all also included. As are a mute button and a dim button, with volume control, that instantly reduces the monitor level by a pre-set amount.
Product type
Other Studio and Recording Equipment
Channels
3 x switchable balanced outputs, 1 x CUE output, 1 x main output
Inputs
3 + SPDIF
Input connectors
3.5 mm TRS , 6.3 mm jack , RCA , SPDIF
Input type
balanced/unbalanced (depending on TS/TRS connection)
Max. input level
20 dBu
Input impedance
(balanced) 10.000 Ohm(s) , (unbalanced) 5.000 Ohm(s)
Outputs
7 x stereo
Output connectors
TRS balanced (1 - 3) , TRS unbalanced (CUE, MAIN, headphones 1 & 2)
Output impedance
600 Ohm(s)
Frequency response
12 - 90000 Hz
Total Harmonic Distortion (THD)
0.002 % (BW 20 - 20,000 Hz)
Signal-to-noise ratio (SNR)
102 dB (a-weighted) @ + 4 dBu
Dynamic range (DR AES17)
115 dB
CMRR
> 55 dB
Max. attenuation
(Attenuator + Mute) 111 dB , (Attenuator) 86 dB
Controls
attenuation , Audio DIM , input selector , mono , mute , output selector , PFL source , Talkback
Housing material
sheet steel , wood
Cabinet surface
Powder coated
Width
254 mm
Height
84 mm
Depth
215 mm
Weight
1,512 kg | Palmer Monicon, and the volume is right!
With Palmer Monicon, your monitor volume is always under control. The passive mini-mixer with the oversized control is inserted between the stereo output of the notebook, PC or interface and an active monitor system and thus permits convenient and precise volume control of the monitors from the workstation. The passive circuitry with only a few components has absolutely no affect on the sound. Mute and mono buttons make it possible to mute the outputs and merge the stereo output signal into a mono master signal.
The inputs and outputs of the controller are equipped with XLR connectors and the 3.5mm stereo TRS sockets usually found on computers. Combo input sockets also permit connection with 6.3 mm TRS plugs. Thus the Palmer Monicon is compatible with both professional and consumer equipment. Genuine wood sides make the practical studio tool in its massive powder-coated sheet steel housing an elegant looking "little helper" that is a typical Palmer product.
- Type: passive
- Number of channels: 2
- Number of inputs: 2
- Input connections: XLR Combo / 3.5mm stereo jack
- Input type: balanced/unbalanced
- Maximum input level: +20 dBu
- Input impedance: 10 kohms balanced/ 5 kohms unbalanced
- Number of outputs: 2
- Output connections: XLR/m, 3.5 mm stereo jack
- Output type: balanced/unbalanced
- Max output level: +20 dBu
- Output impedance: 600 ohms
- Frequency response: 10Hz - 40 kHz +/- 1 dB
- THD: 0,001 %
- Max. attenuation: 85 dB (attenuator), 112 dB (attenuator + mute)
- Controls: Attenuation, Mute, Mono
- Housing material: sheet steel/wood
- Housing surface: powder-coated
- Width: 164 mm
- Height: 62 mm
- Depth: 85 mm
|
Studio Monitor Enhancement Pack
- Nano Patch Plus
- 2x Isolation Pads: 170mm x 300mm x 40mm
- 4 XLR to TRS cables 3m included | Features
- Absorber panels made of high-density-foam
- Optimizes the acoustic performance of your speakers
- 3 different inclination angles
- Suitable for near-field monitors
Specifications
- Color: anthracite
- Size: M
- Dimensions: 250 x 320 mm
- Weight: 250 g
Scope of delivery
Applications
- Damping of vibrations and resonances of studio and hi-fi loudspeakers
- Correction of the inclination of studio and hi-fi loudspeakers
- Height adjustment of studio and hi-fi loudspeakers
|
Perfectly matchd speaker stand for
Studio Monitor 350 and Studio
Monitor 450
|
The M-Patch 2 is a compact desktop/rack-mountable sized passive volume attenuator and patch control device. Building on the success of the original M-Patch, the new M-Patch 2 is a feature packed passive problem solver for nearly all production environments. A great way to passively attenuate stereo signals from soundcards, CD players, pre-amps, and mixers, the M-Patch 2 front panel rotary controls allow precise level adjustments for two input sources. Featuring balanced combo XLR/TRS input jacks and XLR outputs, RCA & 3.5mm jack inputs, mono/stereo summing switch, Mute switch, A/B output pairs, and a built in stereo headphone amplifier, the M-Patch 2 has all bases covered.
- High quality? passive volume attenuator
- Great monitor switching device
- 2 x Input channels, 2 x Output channels
- Combo, RCA, & 3.5mm input connectors
- XLR outputs (balanced or unbalanced depends on the inputs selected)
- Mono/Stereo summing switch
- System mute function
- Built in headphone amplifier
- Quality components and rugged construction
- Desktop or Rack-mountable installation
- External 16Vac power supply (Supplied. Only required for operation of headphone amplifier) |
Reviews
There are no reviews yet.