| Content | Palmer Monicon, and the volume is right!
With Palmer Monicon, your monitor volume is always under control. The passive mini-mixer with the oversized control is inserted between the stereo output of the notebook, PC or interface and an active monitor system and thus permits convenient and precise volume control of the monitors from the workstation. The passive circuitry with only a few components has absolutely no affect on the sound. Mute and mono buttons make it possible to mute the outputs and merge the stereo output signal into a mono master signal.
The inputs and outputs of the controller are equipped with XLR connectors and the 3.5mm stereo TRS sockets usually found on computers. Combo input sockets also permit connection with 6.3 mm TRS plugs. Thus the Palmer Monicon is compatible with both professional and consumer equipment. Genuine wood sides make the practical studio tool in its massive powder-coated sheet steel housing an elegant looking "little helper" that is a typical Palmer product.
- Type: passive
- Number of channels: 2
- Number of inputs: 2
- Input connections: XLR Combo / 3.5mm stereo jack
- Input type: balanced/unbalanced
- Maximum input level: +20 dBu
- Input impedance: 10 kohms balanced/ 5 kohms unbalanced
- Number of outputs: 2
- Output connections: XLR/m, 3.5 mm stereo jack
- Output type: balanced/unbalanced
- Max output level: +20 dBu
- Output impedance: 600 ohms
- Frequency response: 10Hz - 40 kHz +/- 1 dB
- THD: 0,001 %
- Max. attenuation: 85 dB (attenuator), 112 dB (attenuator + mute)
- Controls: Attenuation, Mute, Mono
- Housing material: sheet steel/wood
- Housing surface: powder-coated
- Width: 164 mm
- Height: 62 mm
- Depth: 85 mm
|
MoCo is a fully passive monitor controller that helps you to provide perfect control over the playback volume of your studio monitors.
\"Fully passive\" means that there are no active components involved, that could in any way alter the audio signal - keeping the maximum sound quality level for your studio monitors. MoCo provides two separate stereo inputs (one with balanced 1/4\" TRS connectors, one with both unbalanced RCA and unbalanced 1/8\" TRS connectors) and two separate stereo outputs (one with balanced XLR connectors, one with balanced / unbalanced 1/4\" TRS plus unbalanced 1/8\" TRS connectors). MoCo does not change your signals from unbalanced to balanced: what goes in, goes out!
Via one switch you can select the input signal and with separate buttons, each output can be enabled. Also there is a switch that changes the monitor signal to mono and you can mute the playback audio signal quickly at the touch of a button. A quick swap of the left and right audio signal channels is also possible. And of course, the stylish big knob in the center of MoCo controls the actual playback volume.
Features
- 2x mono balanced 1/4\" TRS input (input A)
- 2x mono unbalanced RCA input (input B)
- 1x stereo unbalanced 1/8\" mini jack input (input B)
- 2x mono balanced XLR output (output A)
- 2x mono balanced / unbalanced 1/4\" TRS output (output B)
- 1x stereo unbalanced 1/8\" mini jack output (output B)
- selected high quality potentiometer for passive volume control
- A/B input selection switch
- L/R switch to swap left & right audio channels
- independent A and B buttons to enable and disable the outputs
- mono downmix button (mixes left to right channel and right to left channel)
- mute button to mute output signal instantly
|
The M-Patch 2 is a compact desktop/rack-mountable sized passive volume attenuator and patch control device. Building on the success of the original M-Patch, the new M-Patch 2 is a feature packed passive problem solver for nearly all production environments. A great way to passively attenuate stereo signals from soundcards, CD players, pre-amps, and mixers, the M-Patch 2 front panel rotary controls allow precise level adjustments for two input sources. Featuring balanced combo XLR/TRS input jacks and XLR outputs, RCA & 3.5mm jack inputs, mono/stereo summing switch, Mute switch, A/B output pairs, and a built in stereo headphone amplifier, the M-Patch 2 has all bases covered.
- High quality? passive volume attenuator
- Great monitor switching device
- 2 x Input channels, 2 x Output channels
- Combo, RCA, & 3.5mm input connectors
- XLR outputs (balanced or unbalanced depends on the inputs selected)
- Mono/Stereo summing switch
- System mute function
- Built in headphone amplifier
- Quality components and rugged construction
- Desktop or Rack-mountable installation
- External 16Vac power supply (Supplied. Only required for operation of headphone amplifier) |
MyMONITOR - Personal Headphone Monitor Mixer Overview
Problem: A performer needs to hear him/herself through headphones exclusively or mixed
with the output of a mixer, CD player, tape deck, or other stereo line level source. Only the
mic signal, however, should be going to the main mixer.
Solution: Connect MyMONITOR between the mic and line source, and the mixer. The Mic
and line Monitor levels can then be adjusted for mix and volume through the headphones.
Only the mic signal will go to the board. And since MyMONITOR can be AC or battery powered,
the unit can be used on a large stage or wherever there is no AC outlet nearby. Dynamic or
condenser mics can be used since phantom power would come through the Mic Thru jack from
the mixer or other source.
MyMONITOR - Personal Headphone Monitor Mixer Specifications:
Signal To Noise Ratio 90dB
Gain 15dB (1/4 in), 50dB (XLR)
Maximum Input Level -20dB mic, 40dB Monitor
Output Impedance 10 ohms
Power Requirements 12V DC (Adapter included) or one 9V battery
Phantom Power ON/OFF switch
Power LED indicator
Dimensions 4.5x2.75x1.5 inches (112mm x 72mm x 40mm)
Weight 1.3lb (590g)
|
The Behringer Monitor2USB is a monitor controller and USB audio interface designed for home and project studios. It pairs a large VCA control knob for your overall output level with the ability to select among three sets of active studio monitors, as well as two sets of headphones. With its USB jack, you can connect your computer straight to the device so that you may play music from your digital library, or you can mix straight from your DAW. Through its XLR inputs, you can route analog sound, balanced or unbalanced.
The VCA amplifier provides several benefits. For example, it allows DC current to flow through the volume control, rather than the audio signal, and thus, bypasses any DC-related signal degradation. This also helps in making sure your stereo image doesn’t drift as you crank the volume knob; anyone who’s experienced in monitor controllers knows this can be a problem—a problem mitigated in the Monitor2USB. The volume knob itself is quite large, and this too serves a function: Such a large size allows for more precision as you turn the control, so you can achieve minutely specific level adjustments, which might be necessary as you switch from monitoring post-production projects to music mixes.
You can use its three sets of outputs in a variety of ways—for instance, you can hook up two monitors and a subwoofer, or three sets of monitors, one of which can serve as your dedicated mono check. On the headphone outputs, a crossfeed control mimics the stereo experience of sitting in front of your speakers by feeding a miniscule amount of signal from the right to the left and vice versa. Amongst other benefits, this feature helps mitigate ear fatigue over long sessions. Mono and Dim buttons are on hand to help you in the mixing process. Included with the Monitor2USB are a power cable and a full, complimentary copy of Tracktion—a DAW to help you in your recording, editing, and mixing journeys.
Key Features at a Glance
- Large volume knob with VCA control for precise level adjustments
- Built-in stereo USB audio interface
- 2 high-quality stereo inputs
- 3 independent monitor outputs to connect two stereo monitors and one mono monitor
- 2 headphone amplifiers with separate volume controls
- Crossfeed control emulates the stereo speaker panorama when listening through your headphones
- Convenient Mono and Dim functions
- Included eco-friendly power supply
- Designed and engineered in Germany
| Analog Inputs |
2 x XLR (input set 1)
2 x XLR (input set 2) |
| Input Impedance |
20 kOhms balanced, 10 kOhms unbalanced |
| Input Sensitivity |
Input Set 1: +4 dBu
Input Set 2: +4 dBu / -10 dBV |
| Analog Outputs |
Monitor Out A: 2 x XLR, balanced
Monitor Out B: 2 x XLR, balanced
Monitor Out C: 1 x XLR, balanced
Phones: 2 x 1/4" TRS, phone type |
| USB |
USB 1.1, type-B |
| D/A Conversion |
44.1 / 48 kHz |
| Frequency Response (-3 dB) |
< 10 Hz to 120 kHz |
| SNR |
85 dB at 0 dB, A-weighted |
| CMRR |
> 50 dB at 1 kHz, 0 dBu input level, unity gain |
| THD+N |
0.03% at 1 kHz, 0 dBu input level, unity gain |
| Crosstalk |
> 75 dB at 1 kHz |
| Attenuation |
Dim: -15 dB |
| Power Supply |
100 to 240 VAC, 50 / 60 Hz |
| Dimensions (H x W x D) |
3.3 x 8.5 x 7.8" / 84.0 x 216.0 x 199.0 mm |
| Weight |
3.3 lb / 1.5 kg |
|
Product details
MonkeyTree is the natural home for our species. The
Monkeys feel well while standing relaxed and decoupled
from the ground.
Our Monkeys love Heavy Metal - thats why we made the
Monkey Tree out of massive Material to guarantee a solid
stand.
One set contents 1 Pair of MonkeyTree
Weight: 12,1kgs / 26.7lb
Max. Load: 70kgs / 154lb
Dimensions (Plate): L240 x W165 x H793 mm
L9.44 x W6.5 x H31.22 in
The MonkeyTree is available with two different pipe-lengths. Please select between 750mm (29.53in) and 1000mm (39.37in)!
The MonkeyTree fits to Turbo 4, Turbo 5, Turbo 6 and Turbo 8.
|
Reviews
There are no reviews yet.