| Content |
User\'s manual
Palmer MI PWT 05 MK 2
Universal 9V Pedalboard Power Supply 5 Outputs
- Universal 9 volt DC power supply
- 5 outlets with ultra stable 250 mA each
- Isolated
- Overload protection
- Roadworthy enclosure
- Mounting and strain relief options
- Power, merge and daisy chain cables included
With a stable 250 mA on each of the five center negative barrel style outlets the compact Palmer PWT 05 MK2 is most suited to virtually any pedalboard size. To deliver clean DC power to your pedals and eliminate ground loops between them and the associated hum the outlets are isolated.
The PWT 05 MK2 is protected against overloading and comes with 25 and 50 cm long connection cables, as well as two Y-cables. The first one, with a black connector, connects two 9 V outputs to increase the current intensity to a massive 500 mA, the other one, with a white connector, connects two 9 V outputs to double the voltage to 18 V.. Also included is a 1-into-5 daisy chain that lets you power five pedals from one output if their total current draw does not exceed 250 mA. The rugged enclosure of the Palmer PWT 05 MK2 provides mounting and cable relief options while the IEC mains inlet and voltage selector enable worldwide use.
Product type
Power Supplies
Mains connector
IEC socket
Input voltage
230 V
Outputs
5
Output connectors
2.1 x 5.5 mm
Output voltage
9 V
Max. output current
each output 250 mA
Isolated outputs
yes
Polarity
center negative
Cord length
25 - 50 cm
Indicators
Overload , Power
Controls
mains switch (on/off) , voltage selector switch
Width
105 mm
Depth
140 mm
Height
45 mm
Weight
1,5 kg
|
FOR X-S, Xio, all ReMOTEs, Bass St. KB/Rack, D-. A-, K-St
|
The PWT12 is universal pedal board power supply with 12 outputs electrically isolated in pairs. Outputs 1 - 8 provide 9 V DC each with a maximum current draw of 250 mA per pair. Outputs 7 and 8 additionally feature a polarity switch to change the center pin from negative to positive (and the barrel to negative).
Outputs 9/10 provide 18 V DC each with a maximum current draw of 125 mA. Additionally, the upper output is switchable to 12 V DC. Providing 9 V DC/250 mA, outputs 11/12 are also switchable to 12 V AC. The green indicator LEDs turn red when alternative ouput voltages are selected.
All output pairs are individually protected against shorts and overload. When a fuse trips the LED indicator of the corresponding pair goes out. After the fault condition has been removed the fuse is automatically reset, and within a few seconds the output resumes operation indicated by the illuminated LED.
The toroidal transformer and the steel housing of the PWT12 provide smooth FX operation free of interference and hum pickup. Mains power input is switchable between 115 V and 230 V.
The PWT12 features two brackets for easy pedal board mounting while a cover plate protects the DC plugs. The DC cables can be fixed to the plate with cable ties for strain relief. The PWT12 comes with a set of 12 long DC cables.
Technical Specifications- Universal power supply for effect pedals
- 12 outputs on barrel-style DC connectors with 2.1 mm center pin
- regulated DC output, all outputs electrically isolated in pairs
- Outputs 1/2, 3/4, 5/6: 9 VDC each, 250 mA per pair, center pin negative, green LED indicators
- Outputs 7/8: 9 VDC, 250 mA/pair, switchable polarity, two-color LED, green = center pin negative, red = center pin positive
- Outputs 9/10: 2x 18VDC (LED = green), switchable to 1x 12VDC / 1x 18VDC (LED = red), maximum current 125mA/pair, center pin negative
- Short circuit protection per pair with automatic reset
- 115 V / 230 V switchable
- Mains fuse: 5 x 20 mm fine wire, 115 V = T 500 mA; 230 V = T 250 mA
- Toroidal transformer, 20 VA continuous
| 12 Volts DC +(-) 1000 mA TC Approved Power Universal mains voltage with releavnt international plug adapters supplied | User\'s manual
Palmer MI PWT 12 MK 2
Universal 12-Outlet Pedalboard Power Supply
- Fully regulated universal pedalboard power supply
- 12 standard centre negative outlets with 2,000 mA output total
- 8 x 9 V outlets (300 mA each)
- 4 variable voltage outlets 6 to 18 V (500 mA each)
- Short circuit and overload protection for each outlet
- DC cables and mains adapter included
The PWT 12 is a heavy duty (2000 mA) universal pedal board power supply with 12 isolated 9 V DC, centre-negative female pin-connector outputs. Four of the outputs feature adjustable voltage from 6 to 18 volts. The variable outputs enable the simulation of voltage drop or \'battery sag\' in old batteries. The power supply is regulated for constant voltage supply and protected against short circuit and overloading. The PWT 12 is equipped with a power LED and a two-colour LED output status indicator. It is supplied with an AC adapter and a set of DC cables. The PWT 12 is the ideal solution for power-hungry foot pedals or 9-volt effects units that can be operated at higher voltages for increased dynamics and stability.
Product type
Power Supplies
Input voltage
100 - 250 V
Outputs
12
Output connectors
2.1 x 5.5 mm
Output voltage
12 V , 18 V , 9 V
Max. output current
2000 mA
Isolated outputs
yes
Polarity
center negative
Cord length
25 - 50 cm
Indicators
fault , Power
Controls
Output voltage selector
Width
193 mm
Depth
70 mm
Height
30 mm
Weight
0,4 kg
|
Universal Effects Pedal Floor Board with Integrated Power Supply
Ultra-compact and lightweight pedal board for transporting up to 12 effects pedals
Generous 1.7 A power adapter included for powering more than 12 devices*—includes all cabling
Ultra-rigid plastic design withstands even heavy impact
High-quality components and exceptionally rugged construction ensure long life
Conceived and designed by BEHRINGER Germany
Love your pedal chain? Rather than tossing your effects and their individual power adapters into a duffel bag after a gig, keep them safe—and ready to rock at a moment's notice—with the PB1000.
It's all about connections
This pedal board makes hooking up 12 2.5" x 4.5" pedals as easy as hooking up just one (of course, if you're using pedals that aren't 2.5" x 4.5“, the snug foam padding can be cut to accommodate pedals of varying shapes). The PB1000 includes ¼" patch cables, so you can leave your pedals connected to one another, ready to pass signal even when you're transporting them. It also comes with 1 x 12 daisy chain cabling so that when you plug in the 1.7 A power adapter, all your pedals receive power.
The Ins and Outs
Connect your guitar, bass or keyboard to the single ¼" input in the upper right corner of the board. A pair of ¼" FROM EFFECTS jacks in the upper left corner allow you to connect stereo effects, and two ¼" OUTPUT TO AMP jacks send a left and right stereo signal to up to two amps. When it is time to load out, just unplug the power supply, disconnect your guitar and amp, put the lid back on the PB1000 and slide the locking latches back into place. The heavy-impact plastic casing will protect your pedals from the rigors of the road.
Value
You have invested considerable time and money into your effects chain. Keep it safe and sounding great with the PB1000. Check it out at your nearest BEHRINGER dealer.
User's Manual
|
Reviews
There are no reviews yet.