Content |
EWI PDI-100 PARA ACOUSTIC DI Box
This is a medium grade professional application Para Acoustic Active DI, which will work well on instruments with passive pickups or active pickups.
The construction is reasonably rugged and the components are well suited for the application yielding results that are typically acceptable for all but the most discerning artists.
The on-board tone and volume controls give the operator a lot of choices in shaping their sound prior to sending the signal to the mix console. This allows an artist to use this device in-place of or in addition to a traditional stage amp for their instrument. This is an excellent choice for IEM bands, or bands that like to keep their stage volume low.
This item is typically used to split the instrument signal going to a stage amp so a feed can be sent also to the mix board, or be used as a stand-alone instrument pre-amp. It is equipped with a ¼” jack for input, a 1/4" jack for output to a stage amp, one XLR jack for the send to the board and a TRS jack for inserting an FX device.Since this is an active D.I. box, it needs to be powered which can be done either with Phantom Power from the mix board, or with the supplied internal 9v battery. The battery is fairly easy to change by removing one screw in the bottom of the case.
| ISA OneClassic Single-channel Microphone Pre-amplifier with Independent D.I.
Key Features
ISA Series Transformer-based Pre-amplifier
Encased in a rugged and portable chassis, ISA One offers the classic Focusrite microphone pre-amplifier at its lowest cost to date.
Flexible Independent D.I. Channel
ISA One is ideal for both engineers and demanding performers alike, featuring independent gain control, an output for routing to an amp, an independent XLR output on the rear and routing to the optional ADC.
Switchable Impedance
Choose one of four carefully selected input impedances, including the original ISA 110 setting, to suit any microphone.
Optional Stereo 192kHz ADC
This optional card embodies cutting-edge conversion technology, incorporating Focusrite analogue circuitry to deliver the best A-D performance in its class (Dynamic range of 119dB).
Rugged Custom Flight Case
Built to protect your ISA One from the rigors of the road. Rugged plywood construction with a solid polypropylene exterior and reinforced corners.
Headphone Output with Volume Control
ISA One can feed either a sum of the two inputs to the headphones output, or an external stereo cue mix (such as a stereo mix feed from an interface) via two TRS Jack inputs on the rear of the unit.
Dedicated Insert Point
Allows you to place extra processing between the pre-amplifi er or D.I. and the optional converter, such as an EQ or compressor.
Specifications
Analogue Channel Inputs
- XLR Mic input
- One XLR and one TRS line input
- XLR Instrument input TRS Jack
- External ADC input TRS Jack
- TRS jack return
|
Analogue Channel Outputs
- TRS jack send
- XLR balanced line output
- XLR DI output
- TS jack DI through
|
Analogue Channel Additional I/O
- TRS Jack cue mix left input
- TRS Jack cue mix right input
- 1/4” TRS Jack headphones output
|
Mic Input Response
Gain range |
0dB to 60dB in 10dB steps + 20 dB of variable gain |
Input Impedance |
Switched Impedance setting Equivalent Input Impedance at 1kHz |
Low = 600 Ohms
ISA110 = 1400 Ohms
Med = 2400 Ohms
High = 6800 Ohms |
EIN (Equivalent Input Noise) |
-126dB measured at 60dB of gain with 150 Ohm terminating impedance and 22Hz/22kHz band-pass filter |
Noise |
Noise at output with unity gain (0 dB) and 22 Hz-22 kHz band pass filter |
-97 dBu |
Signal-to-Noise Ratio |
106 dB relative to max headroom (9dBu) |
Total Harmonic Distortion + Noise |
Measured at medium gain (30dB) with a 1kHz -20dBu input signal and with a 22Hz/22kHz band-pass filter |
|
Frequency Response |
At minimum gain (0 dB) |
-0.5dB down at 10Hz and -3dB down at 125kHz |
|
At maximum gain (60dB) |
-3dB down at 16Hz and -3dB down 118kHz |
CMRR (Common Mode Rejection Ratio) |
98dB (Channel 1, 1kHz, maximum gain with +24 dBu input) |
Crosstalk Channel to Channel |
With 10dB@1kHz input to chA, chB output =104dBrA. With 10dB@10kHz input to chA, chB output = 84dBrA |
Line Input Response
Gain range |
-20dB to +10dB in 10dB steps + 20 dB of variable gain |
Input Impedance |
10 kΩ from 10 Hz to 200 kHz |
Noise |
Noise at main output with gain at unity (0 dB) measured with 50 Ω source impedance and a 22Hz - 22 kHz band pass filter |
-96 dBu |
Signal-to-Noise Ratio |
Measured with a 22 Hz-22 kHz band pass filter |
120 dB relative to max headroom (24 dBu)
118dB relative to 0dBFS (+22dBu) |
Total Harmonic Distortion + Noise |
Measured with a 0 dBu input signal, and a 22 Hz-22 kHz band pass filter |
0.0001% |
Frequency Response |
At unity gain (0 dB) |
-0.3dB down at 10Hz and -3dB down at 200kHz |
Instrument Input Response
Gain range |
10dB to 40dB continuously variable |
Input Impedance |
High = greater than 1M
Low =greater than 300k |
Noise |
Measured with 22 Hz-22 kHz band pass filter |
Minimum gain (+10 dB): -92 dBu
Maximum gain (+40dB): -62dBu |
THD |
At minimum gain (+10) |
Frequency Response |
At minimum gain (+10 dB) |
-10dB input: 10Hz-100kHz +/- 0.6dB |
|
At maximum gain (+40 dB) |
-40dB input: -2.5dB down at 10Hz and 0dB at 100kHz |
Meters
Moving Coil (MC) Meter |
factory calibrated to 0VU = +4dBu with 1kHz sinewave. With the VU Cal button pressed the meter can be adjusted on the rear panel to allow 0VU to equal +10dBu to +26dBu with the centre detent being equal to +22dBu. |
Peak LED Meters |
Calibrated in the detent position for 0dBFS = +22dBu, calibration is adjustable on the rear panel to allow 0dBFS to equal +10dBu to +26dBu |
Routing for MC and Peak1 meter is after the HPF, pre insert send or switched post insert return. Peak2 is always pre ADC channel 2, which can be fed by external input or Instrument input. |
LED Levels |
As follows, when peak calibration is set to center detent on the rear panel. (This is when using the internal ADC). |
0 = +22dBu
-2 = +20dBu
-6 = +16dBu
-12 = +10dBu
-18 = +4dBu
-42 = -20dBu |
Frequency Response |
At minimum gain (+10 dB) |
-10dB input: 10Hz-100kHz +/- 0.6dB |
|
At maximum gain (+40 dB) |
-40dB input: -2.5dB down at 10Hz and 0dB at 100kHz |
High-Pass Filter
Roll-Off |
18 dB per octave (3 pole filter) |
Frequency |
Fixed 75Hz measured at the 3dB down point |
Weight and Dimensions
W x D x H |
220mm (W) x 104mm (H) x 254 - 290mm (D - top to bottom) |
8.66" (W) x 4.1" (H) x 10" - 11.4" (D - top to bottom) |
Weight |
3.9 kg |
8.6 lbs |
|
PreSonusʼ popular Class A XMAX preamps are widely lauded for their clarity and transparency. Our tube preamps are beloved for their warm, smooth sound. With the Blue Tube DP V2 dual-path mic/instrument preamp, you get both types of high-quality sound in one unit.
Now weʼve improved on the classic unit with the BlueTube DP V2. The solid-state path now feeds PreSonusʼ top-of-the-line Class A XMAX™ mic preamplifier with 80 dB of variable gain—an upgrade from the original BlueTube DPʼs solid-state stage.
You still get all the secondary features you expect in a professional-grade preamp: 48V phantom power, an 80 Hz high-pass filter, -20 dB pad to control hot input signals, and a polarity-reverse switch. Each channel has an illuminated VU meter so you can visually monitor your input levels.
A Tube Drive control provides a wide range of sounds: when itʼs clicked off, youʼre using the solid-state preamp for quiet, transparent amplification; when itʼs engaged, your signals flow through the tube preamp, and you can achieve anything from gentle warmth to edgy distortion.
2 input channels, each with:
High-headroom Class A XMAX™ mic preamplifier with 80 dB gain range
12AX7 vacuum tube gain stage
Tube Drive tube-saturation control
48V phantom power
80 Hz high-pass filter
-20 dB pad to reduce hot input levels
Polarity-reverse switch
Illuminated analog VU input-level meter
Input/Output
2 balanced combo mic/unbalanced instrument inputs
2 balanced XLR main (L/R) line outputs
2 unbalanced ¼” main (L/R) line outputs
Physical
Compact 1/2U chassis
External 12 VDC, 1A power supply
|
The PRE-73 Mk2 is the first one-channel low-cost preamp on the market that is using a fully discrete signal path with three separate transformers for the balanced mic input, the line input and the output.
The circuit is very similar to the classical preamp section of the Neve 1073 pre/eq module with a corresponding sound character that is warm, punchy, sweet and musical.
This classical sound has been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres.
The PRE-73 Mk2 has a maximum gain of 80 dB on the mic input and the gain range on the Line input is -20 to + 10 dB. There is also a high-impedance instrument input.
The PRE-73 Mk2 is perfect for almost any signal source, no matter if it's a microphone with a high or low sensitivity (like a passive ribbon mic), a syntheziser or sound module or an electric guitar or bass.
The input impedance of the microphone input can be switched between 300 and 1200 ohms, which makes it possible to affect the tone of most microphones. There is also phase switch and an simple 4-step LED signal level meter.
The output level control makes it possible to make fine gain adjustments and also to overload the main gain stage for more character and then lower the signal to a suitable level before the output stage.
The Mk2 update consists of:
- An unbalanced insert jack (nominal level about 18 dBu) added on the back panel for inserting units like the coming GAP EQ-73, a three band eq.
- LED meter levels adjusted.
- 600 Ohm termination resistor and jumper added to power supply board (accessible from the inside of the unit).
- Revised Gain switch, turning the know clockwise now increase the gain.
- Reduced noise at high gains by a change to the power supply grounding scheme. | • Solid housing
• RIAA Equalization
• High quality components
The PRE-101 is a phono pre-amp with RIAA equalization. The tiny signal of magnetic pick-ups is amplified to fit the line-level inputs of mixers or USB sound-cards.
Specifications Frequency Response: 20Hz-20KHz RIAA
Inputs: RCA
Outputs: RCA
Input sensitivity: 3mV for 1000 mV output
Input Impedance: 47 kOhm
Nominal Output Voltage: 0 dBV
Max Output voltage: +16 dBu
Output impedance: 100-600 Ohms
Power supply: 18V AC (adapter included)
Dimensions: 40 x 113 x 80 mm (HxWxD)
Weight: 0,35 Kg |
The PRE-73 DLX is a one-channel vintage style microphone-, line- and instrument preamplifier. The signal path uses only discrete components like resistors, capacitors and transistors. The line and microphone input and the line output are transformer balanced, using three different transformers, each one optimized for its purpose.
This is the way audio components were built before integrated circuits became available. The subjective sound quality delivered by vintage equipment is often prefered over the one delivered by modern units, a situation that is even more obvious now when music is recorded with clean-sounding digital audio equipment.
The circuit used in the PRE-73 DLX is similar to the preamp section in the classical 1073 module with a corresponding sound character that is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres. The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.
FEATURES
- Vintage Style electronics. No intergrated circuits in the signal path.
- Maximum gain on the mic input is 80 dB, enough to handle passive ribbon mics with quiet sound sources.
- Gain range on the Line input: -20 to + 10 dB.
- Switchable impedance on the mic input, 1200 or 300 Ohms, will change the tone of most mics.
- Switchable phantom power and absolute phase.
- A high-impedance instrument input for any sound module, electric guitar or bass.
- A simple but effective 4-step LED output level meter.
- The output level controls makes it possible to make fine gain adjustments and also to overload the main gain stage(s) for more character and then lower the signal to a suitable level before the output stage.
- Combo XLR/TRS input jacks and separate output XLR and TRS jacks for flexible connections.
- Insert jack for inserting EQ´s and other units.
- External high power power supply to avoid interaction with the audio circuits and transformers.
- A solid build quality that will last many years of normal use.
The PRE-73 DLX has a number of improvement and new features compared to the PRE-73 MKII:
- Tantalum capacitors in the signal path.
- Selectable 1073-style high pass filter, 50Hz, 80Hz, 160Hz and 300Hz.
- Output Attenuator -7, -14, -21 and -28 dB (located after the output transformer) allows overdriving the output stage and the output transformer for added character by lowering the output signal to a suitable level.
- The circuit board is prepared for Carnhill Mic and Line transformer and high pass inductor.
- The Insert jack can be switched in/out from the front panel. An internal jumper can select that the Insert jack always has an output signal.
- Switchable 600 ohm Output Termination and Ground Lift on the back panel.
- Selectable Active or Passive DI input and selectable input impedance in active mode, Hi Z or 100 kohm, by internal jumpers.
- The DI can signal can be selected to pass or bypass the mic input transformer by internal jumpers.
- Relays are used to control internal switching for DI input, Phantom power, Mic Low Z, Insert and Phase for shorter circuit board signal paths. The relays are controlled by front panel switches.
- Revised gain switch for added headroom.
- Circuit board star grounding scheme.
- Revised power supply with separate regulators for the audio circuits and relay and LED circuits.
|
Reviews
There are no reviews yet.