| Content |
- Stereo (dual channel), parallel-input, or bridged mono operating modes with selector switch
- Noise-free on-off
- 2 dual speed fans for cooling
- Binding post (banana plug) outputs
- Built-in DC offset
- Independent DC and thermal overload protection on each channel
- DC servo operation
- Ground lift switch
- Road-worthy, rugged double rack space (2U) housing
- Power ON, Clip, Signal, and Protect LED indicators for each channel
- Parallel balanced XLR and 1/4 TRS inputs
- Built-in digital current limiter
- Detent volume controls
- Short circuit and speaker protection
- 1500 Watts
- ~115(60Hz)/~230V(50Hz) AC select switch and IEC power cord connector
|
This professional stereo power amplifier, working in class-H mode, provides 2x800W, at an efficiency of around 85%.
A passive transformer based power supply and hand selected components makes this power rating possible with exceptional audio quality and absolute reliability, even in the 2 Ohm mode. The output stage is fully protected against over-temperature, short circuit, RFI and equipped with soft start circuit and temperature-controlled fan cooling. The integral soft clip limiter protects against damage to the connected loudspeakers. The activity of a protective circuit, signal and limiter is shown for each channel by LEDʼs.
| AMPLIFIER SPECIFICATIONS |
|---|
| Power output stereo 2Ω: | 2 x 800 Watt rms | | | Power output stereo 4Ω: | 2 x 650 Watt rms | | | Power output stereo 8Ω: | 2 x 350 Watt rms | | | Power output bridged 4Ω: | 1600 Watt rms | | | Power output bridged 8Ω: | 1300 Watt rms | | | Frequency Response: | 20 Hz ÷ 20 kHz | | | Signal/noise rate: | > 103 dB | | | Crosstalk: | > 70 dB | | | Distortion (THD+N): | | | | Intermodulation: | | | | Damping factor: | 200:1 (8 Ω) | | | Slew rate: | 50 V/μS | |
| INPUT SECTION |
|---|
| Input connector: | 2 x XLR balanced, 6,3mm jack unbalanced | | | Input sensitivity: | 0 / 0.775 dBm/V RMS | | | Input impedance: | 20.000 kΩ | | | Controls: | Volume control for each channel | |
| OUTPUT SECTION |
|---|
| Output connector: | 2 x Neutrik Speakon 4 ways | |
| SYSTEM PARAMETERS |
|---|
| Cooling: | Two-speed fan | | | Protections: | Temperature, DC, RFI short circuit, Soft-Start, Thermal on transformer | |
| POWER REQUIREMENT |
|---|
| Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 V ~ Hz | | | Max.current: | 7.5 A | | | Power Consumption: | 2700 W | |
| PHYSICAL SPECIFICATIONS |
|---|
| Height: | 88 / 3.46 mm/inch | | | Width: | 483 / 19.01 mm/inch | | | Depth: | 455 / 17.91 mm/inch | | | Net Weight: | 19.5 / 42.98 Kg/Lbs | |
| SHIPPING INFORMATION |
|---|
| Package height: | 150 / 5.9 mm/inch | | | Package width: | 555 / 21.85 mm/inch | | | Package depth: | 525 / 20.66 mm/inch | | | Shipping Weight: | 20 / 44.09 Kg/Lbs |
|
BASIC Series - Intelligent Power
BASIC - that's meeting the tightest budgets and professional requirements
in reliability, flexibility and sound. Alone or in combination with the other
products of the Bittner portfolio.
The consequent realisation of the Bittner quality standards indicates once
more our understanding of the contracting business. It underlines our philosophy
that cost consciousness has nothing to do with giving up standards. Compromise
is a word unknown to Bittner Audio!
The incorporation of detent potentiometers, clip limiter, protection circuits for
any imaginable situation, as well as a first-class production process using only
highest-quality components made the BASIC series the choice of most contractors.
Certainly more than basic!
High Tech SMT design
Excellent sound and superior impulse response
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
XLR Inputs
Speakon and Binding Posts
Clip Limiter
Toroidal transformers
LED Indicators for SIGNAL, CLIP, PROTECT, POWER
Temperature controlled, variable speed, low noise fans
Detent potentiometers
Stereo / Bridged / Parallel Mode
Ground Lift
Robust Steel Chassis
3 Year Warranty
TECHNICAL DATA:
Basic 1200: 2x 600 W @ 4 Ohm
Class: AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.03%
Signal-to-Noise Ratio: < -102 dB
Channel Seperation: > 85 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Damping Factor: > 400 @ 4 Ohm
Cooling: 2x Fan (temp. reg. variable speed)
Weight: 15 kg.
Dimensions : 2 RU / 483 x 88 x 454 mm (19" x 3.5" x 17.9“) |
Crown DSi 2000 2x800W-4Ω Power Amplifier
The Crown? DSi 2000 power amplifier shall be a solid-state two-channel model with a switch-mode universal power supply. A rear-panel HD-15 connector shall provide input/output connectivity between the DSi amplifier and the DSi-8M System Monitor.
The outputs shall be usable as stereo or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to access menu items and front panel lockout.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input.
?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below clip.
?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers or bridge-mono loudspeaker.
HiQnet USB Connector: Type B, connects to a HiQnet network.
HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor.
The amplifier shall have the following specifications:
Output Power: 2 ohm Stereo (per channel): 1,000W with 1% THD, 4 ohm
Stereo (per channel): 800W with 0.5% THD, 8 ohm Stereo (per channel) 475W
with 0.5% THD, 4 ohm Bridge-Mono: 2,000W with 1% THD, 8 ohm Bridge-
Mono: 1,600W with 0.5% THD.
Voltage Gain at 1kHz, 8 ohm rated output: 26 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity at 8 ohm rated output: 3.09V.
Sensitivity at 4 ohm rated output: 2.84V.
Sensitivity at 2 ohm rated output: 2.24V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB
(A weighted).
Damping Factor: Better than 500 from 20 Hz to 500 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms,unbalanced.
Maximum Input Signal: +22 dBu typical.
| Solid DYNACORD amplifier technology at highly competitive prices.
These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.
Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 1250 W, 4 Ω - 900 W, 8 Ω - 550 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 2450 W, 4 Ω - 1400 W, 8 Ω - 700 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 2800 W, 8 Ω - 1800 W Input Sensitivity, rated power @ 8 Ω, 1 kHz +5.1 dBu (1.39 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class H Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 16.3 kg (35.9 lbs) |
XR Series - Intelligent Power
New Horizons.
A lightweight with enormous power output. Combined with digital signal processing.
That's what we call flexibility! Locally controlled or completely networked.
No matter what the requirements are.
The integrated powerful digital signal processor (DSP) and controller allows
for a troublefree and easy adjustment to any acoustical environment.
Wear-free digital potentiometers, sequential remote power on,
alive contacts for easy supervision, computer controlled monitoring -
its enless list of useful feature make it the right choice for any installation.
XR - the new definition of Intelligent Power
High Tech SMT Design
Digital Signal Processor
Excellent sound and superior impulse response
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX / Speakon
High-End Switched Power Supply with Power Factor Correction (not XR4000)
LED Indicators for SIGNAL, CLIP, PROTECT, POWER
Temperature controlled, variable speed low noise fans
Digital wear-free Volume Controls (can be operated manually)
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Paging Input
Monitor Output
SXL Dataport
Perfect Weight-to-Power ratio
3 Years Warranty
Technical Data:
Class: H
Frequency Response:20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.02%
Signal-to-Noise Ratio: < -106 dB
Channel Seperation: > 85 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Damping Factor: 750 to 1200 @ 4 Ohm
Cooling: 4 Fans (temp. reg. variable speed)
Weight: 8 to 10 kg (18 to 22 lbs)
Dimensions: 2 RU / 483 x 88 x 454 mm(19" x 3.5" x 17.9“)
|
Reviews
There are no reviews yet.