Stereo (dual channel), parallel-input, or bridged mono operating modes with selector switch Noise-free on-off 2 dual speed fans for cooling Binding post (banana plug) outputs Built-in DC offset Independent DC and thermal overload protection on each channel DC servo operation Ground lift switch Road-worthy, rugged double rack space (2U) housing Power ON, Clip, Signal, and […]
Stereo (dual channel), parallel-input, or bridged mono operating modes with selector switch
Noise-free on-off
2 dual speed fans for cooling
Binding post (banana plug) outputs
Built-in DC offset
Independent DC and thermal overload protection on each channel
DC servo operation
Ground lift switch
Road-worthy, rugged double rack space (2U) housing
Power ON, Clip, Signal, and Protect LED indicators for each channel
Parallel balanced XLR and 1/4 TRS inputs
Built-in digital current limiter
Detent volume controls
Short circuit and speaker protection
1500 Watts
~115(60Hz)/~230V(50Hz) AC select switch and IEC power cord connector
VLP Series Power Amplifier
Output Power:
750W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD
500W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD
(Bridge Mode, Mono)
1500W RMS @ 8 Ohms, 1K Hz, 1% THD
Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)
Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
Slew Rate: 15V Per usec
Damping Factor @ 8 Ohm: 300
Impedance: 20 Ohms balanced / 10 Ohms unbalanced
Cooling System: 2 indivdual fans
Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift / Limiter
Dimensions (LxWxH): 14" x 19" x 3.5" / 360 x 482 x 88mm 2-rack mount spaces
Weight: 42 lbs. / 19 Kgs.
Special Features: High/Low Pass Filter; Input Sensitivity Selector; Ground Lift; Limiter
Crown XTi2002 Specifications:
* Output Power 2 ohms Stereo (per ch): 1000W
* Output Power 4 ohms Stereo (per ch): 800W
* Output Power 8 ohms Stereo (per ch): 475W
* Output Power 8 ohms Bridged-Mono: 1600W
* Output Power 4 ohms Bridged-Mono: 2000W
* Sensitivity (for full rated power at 4 ohms): 1.4 Vrms
* Frequency Response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB
* Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms): 100 dB (A weighted)
* Total Harmonic Distortion (THD):
* Damping Factor 20 Hz to 1 kHz: > 500
* Crosstalk (below rated power): 20 kHz - 1 kHz: > 70 db
* Input Impedance (nominal): 20k ohms balanced, 10k ohms unbalanced
* Maximum Input Signal: +22 dBu typical
* Operating Temperature: 0°C to 40°C at 95% relative humidity (non-condensing)
* Level Control: Two front-panel rotary level controls, one for each channel
* Power Switch Control: On/Off switch applies AC power to the amplifier
* Sel/Prev/Next Buttons Controls: Three buttons near the LCD screen that are used to access menu items and front panel lockout
* LCD Screen: Backlit liquid crystal display that shows preset and processing status
* Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).
* –10 Indicator: Green LED flashes when output signal exceeds -10 dB below clip.
* –20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clip.
* Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
* Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion
* Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions
* Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power
* Input Connectors: XLR, one per channel
* Link/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel.
* Output Connectors: Two Neutrik Speakon NL4MP output connectors. Channel-1 Speakon is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors).
* HiQnet™ USB Connector: Type B, connects to HiQnet™ network.
* Chassis: Steel
* Front Panel: Cast-aluminum
* Cooling: Proportional speed fan with front-to-rear airflow.
* Dimensions: 19" (W) x 3.5" (H) x 12.25" (D)
* Net Weight: 18.5 lbs (8.4kg)
* Shipping Weight: 21.5 lbs (9.8kg)
Number of Channels: 2
Output Power: (per channel)
8 ohms 450W
4 ohms 850W
2 ohms 1550W
Output Power: (bridged)
8 ohms 1700W
4 ohms 3100W
THD%: (@1dB below max output)
@ 1kHz
Crownʼs new CTs series of power amplifiers are remarkable for their loud, punchy sound; sustained, tight bass; and superior protection against overheating and overload. This paper explains the design features behind those advantages. After reading this information, youʼll know why Crown CTs amps sound better than the competition. CTs amplifiers can provide large amounts of power into various loads, such as 2, 4, 8 ohms and 70V. With most power amps, the maximum output power tends to drop as the load impedance increases. But with the CTs series, the power stays the same at almost any impedance. 2-ohm Dual (per Ch.) 250W 4-ohm Dual (per Ch.) 600W 8-ohm Dual (per Ch.) 600W 16-ohm Dual (per Ch.) 300W 70V Dual (per Ch.) 600W 4-ohm Bridge 500W 8-ohm Bridge 1200W 16-ohm Bridge 1200W 140V Bridge 1200W Crown switching power supply for less weight Sustained Power on long-duration signals due to regulated, "stiff” power supplies with incredible energy storage (huge filter capacitors). Extra Hidden Power during high-level transients and during incomplete use of all the channels. Overheating and overload protection thanks to the sophisticated TLC circuitry which compresses the signal only when needed. Compression is controlled not by temperature, but by signal voltage. This keeps the loudness up during compression more than with competitive amps.
The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment.
In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep.
• Ultra-compact and lightweight 2-U high
• Laser cut aluminum front panels with integrated carrying handles
• Neutrik® XLR input connectors, input and signal link in 2 channel models
• Input Link switch: allow daisy-chaining of the input signal
• Neutrik® Speakon® output connectors
• Detented sealed potentiometers for easy recall of volume settings
• ICL™, PMS™, Hi-temp, Signal indicators per channel
• Power on and Stand-by leds
• Highly versatile with multiple configuration and additional module options
• Full PC control via EtheRAM (with EtheRAM Control module)
• Switchable ICL™ clip-limiters per channel
• Switchable (30-50 Hz) sub-sonic highpass filter per channel
• Three-position gain selector (26, 32 or 38 dB)
• Dual or bridge mode selector
• Twin temperature controlled, back to front cooling fans
• Oversized power components (high SOA reserve specification)
Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility.
Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics:
• 2-way stereo crossover (dual mono or single bridged sub output)
• 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz)
• Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB)
• Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB)
DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics:
• 4 Inputs/4 Outputs or 2 In/2 Out free route configurable.
• 24 bits/192 kHz 256x Oversampling Converters.
• Output Delay: 0 to 7.1 meters (20.69ms) per channel.
• XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel.
• EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB).
• Gain, Mute and Phase inversion per channel.
• RMS Power and Peak Voltage output limiter per channel.
• Real Time operation from USB or front panel configuration.
Standard Signal Inputs Module
EtheRAM Control Module
Ethernet Audio Transport (Coming soon)
Analog Processor Module
DSP44_S Module
EtheRAM Control Module
AES/EBU Digital Input (Coming soon)
OUTPUT POWER
S-1500
S-2000
S-3000
S-4000
S-6000
S-3004
S-4004
S-4044
S-6004
S-6044
1kHz, 1.0% THD
2 ohms
2x880W
2x1190W
2x1570W
2x1950W
2x2950W
4x700W
4x980W
-
4x1440W
-
4 ohms
2x575W
2x790W
2x1100W
2x1380W
2x2025W
4x500W
4x670W
4x975W
4x1000W
4x1480W
8 ohms
2x325W
2x460W
2x630W
2x810W
2x1250W
4x300W
4x430W
4x690W
4x620W
4x1015W
Bridge @ 4ohms
1760W
2380W
3140W
3900W
5900W
2x1400W
2x1960W
-
2x2880W
-
Bridge @ 8ohms
1150W
1580W
2200W
2760W
4050W
2x1000W
2x1340W
2x1950W
2x2000W
2x2960W
P. N. 12dB C.F.
2 ohms
2x975W
2x1360W
2x2060W
2x2460W
2x4225W
4x890W
4x1170W
-
4x2080W
-
4 ohms
2x610W
2x880W
2x1240W
2x1600W
2x2600W
4x580W
4x820W
4x1230W
4x1280W
4x2110W
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V
3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V
Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB
3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB
Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A
3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A
Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches
Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs
Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
![back_s_l](http://"images/ram/back_s_l.jpg“/ "back_s_l")
Reviews
There are no reviews yet.