| Content |
- Quasi-three way, full-range/bi-ampable Sound Reinforcement system
- 69Hz to 17kHz
- Two 15 BWX Black Widow 4" diameter VC woofers
- Exclusive Quadratic Throat Waveguide? technology
- 2,000 watts program, 4,000 watts peak
- Two 15" BWX Black Widow 4" diameter VC woofers
- Full-range inputs include two 1/4" phone jacks, one four-pin, twist lock connector & one Neutrik NL4 Speakon switching jack (bi-amp only)
- Asymmetrical horn aims the sound down 10° (at the audience, not over their heads)
- Full length black powder coated metal grille
- RX?22CT compression driver
- M8 threaded mounting suspension points (3 top, 3 bottom and 2 each side & 1 each top rear and bottom rear)
- Sound Guard III tweeter protection
- Four large rubber feet on bottom for floor use
- Trapezoidal plywood enclosure finished in black textured paint
- Weight Unpacked: 43.3 kg
- Weight Packed: 45.3 kg
- Width Packed: 54.991 cm
- Height Packed: 124.9934 cm
- Depth Packed: 51.0032 cm
| The P3115-T is a weatherproof full range, wide-dispersion, coaxial two way loudspeaker system offering substantial power and efficiency for a variety of professional indoor or outdoor applications.
The high-frequency section is a constant directivity CMD horn loaded to a 1” RCF Precision Neodymium compression driver with a 1.5” diaphragm assembly for smooth, wide dispersion. The low-frequency transducer is a 15” woofer with a 2.5” voice coil. The P3115-T features a selectable line transformer for 70 - 100 Volt applications. P 3115-T meets the requirements of IP 55 code (International Protection Rating).
- Cabinet is a single piece rotational moulded in medium density polyethylene, fully UV protected and waterproof IP 55
- Front grille in custom perforated aluminium with open-cell fibres and water repellent woven fabric backing
- Stainless steel bracket
- 15" high-output LF transducer with 2" voice coil
- RCF Precision Neo 1" Compression Driver with 1.5" voice coil
- 90° x 60° constant directivity horn
- 10° X 20° enclosure sides for array configurations
- Active Mosfet Compression Driver Protection
- 12 brass suspension points (M10)
- Line transformer
Acoustical Specifications
- Frequency Response -10 dB: 75 Hz ÷ 20 kHz
- Max SPL @ 1m: 129 dB
- Horizontal coverage angle: 90°
- Vertical coverage angle: 60°
- Directivity index; Q: 13.3
- System Sensitivity: 98 dB
- Nominal Impedance: 16 Ω
- Power Handling: 300 W
- Peak Power Handling: 1200 W
- Protections: dinamyc
- Crossover frequencies: 1300 Hz
Transducers
- Compression Driver: 1" HF driver, 1.5" voice coil
- Nominal Impedance: 8 Ω
- Input Power Rating: 25 W AES
- Sensitivity: 108 dB
- Woofer: 15" woofer, 2.5" voice coil
- Nominal Impedance: 16 Ω
- Input Power Rating: 250 W AES
- Sensitivity: 98 dB
Input Section
- Input connector: 4-adriges Neopren Kabel, 5m
- Constant voltage transformer: 70/100 V
- Power Selection: 70V/60W, 30W , 100V/120W, 60W
Cabinet
- Cabinet Material: Polyethylene rotomoulded
- Hardware: 12 x M10 inserts+ U-brackets and pair of spacers
- Grille: Custom perforated aluminium grillewith open-cell fiber and water repellent woven fabric backing
- Colour: grey
Physical Specifications
- Height: 463 / 18.22 mm/inch
- Width: 463 / 18.22 mm/inch
- Depth: 433 / 17.04 mm/inch
- Net Weight: 19.4 / 42.76 kg/lbs
|
Club Series V
Gigging bands, mobile DJs and houses of worship have helped make the first four generations of Yamaha Club Series Speakers incredibly popular. The refinements of generation V continue this success story: larger enclosures for improved low-frequency performance, improved drivers for higher power handling, redesigned crossovers, stronger grilles, and dual Speakon® and ¼" connectors. Once again, with professional features, excellent sonic performance and great value, Club Series loudspeakers deliver premium quality night after night.
Yamaha has a long history of both making and reproducing music. The Club series V loudspeakers represent the latest in our continuing effort to provide the professional features and sound quality you've come to expect and deserve.
Built in the United States, these loudspeakers are designed to provide years of service. high power handling and excellent response have made Club Series loudspeakers the perfect choice for more than 16 years. Whether playing in a band, DJing, orupgrading the sound system at your church or school, with an expanded lineup of over twenty models to choose from, you're sure to find the right loudspeaker. Have a look at what goes into their construction -- Cabinets are constructed of high quality particleboard, chosen for its high strength and elasticity, consistent void free makeup and light weight. Another great benefit of this material is its environmental friendliness. Made from southern yellow pine, this material is both abundant and quickly renewable. Accurate CNC routing machines are used to cut every part, assuring consistency with tolerances of one ten thousandth of an inch. Skilled technicians assemble each cabinet by hand, rejecting any defects. Whether covered in durable carpet or the elastomeric spray coating, heavy steel handles and sturdy pole sockets make moving and positioning easy.
The drivers, or speakers in these cabinets, are custom made my Eminence Speaker Corporation® to Yamaha's exacting tolerances. Woofers share design features like high strength curvilinear cones and Dupont KaptonTM voice coil formers. Oxygen-free copper voice coils and oversize strontium ferrite magnets are also used to provide high power handling and long life. The 15" and 18" drivers use cast aluminum frames to support the massive magnet structure, eliminate flex and help dissipate heat. The compression driver that generates the high frequency sound uses a pure titanium diaphragm. This 2" dome is one of the largest in its class, allowing for very high output and low distortion, without the aid of cooling fluids. It's mated to a 90° x 40° custom designed CD (constant directivity) horn with excellent dispersion and response.
Crossover networks that divide the signal going to the woofer and compression driver are constructed with oversized coils, high voltage capacitors, and power resistors designed to provide the best possible sound quality and minimize loss. Overload protection is also included to protect the components.
Connections on these loudspeakers are dual Neutrik Speakon® ¼ jacks for the highest possible strength and current capacity. Two of each connector makes it easy to "daisy chain," or add speakers.
Club V loudspeakers with the C prefix are coated with a heavy-duty elastomeric spray coating. Designed as an installation alternative to the carpeted S versions, they can easily fit any decor. The finish is very tough, and readily paintable to match surroundings. The steel grilles are foam-lined with acoustically transparent material to provide a more subdued appearance.
C215V
Two 15" cast frame woofers
2000-watt peak power handling
90 x 45 degree CD horn
Perfect where high sound pressure levels are required
Features:
- Tough, paintable exterior coating
- Dual cast-frame 15" drivers
- Frequency response: (-10dB) 42Hz - 16kHz
- 1,000W program handling, 2,000W peak
- Sensitivity: 99dB
- 20“W x 46“H x 24“D
- 101 lbs.
| | | Woofer | Tweeter
(diaphragm) | Freq
Resp
(-10dB) | Power
Handling
(noise 1 /
program/peak) | Sen-
sitivity | Max.
SPL 3 | Dims.
(WxHxD) 2 | Wt. 2
(lbs) |
| 15" (2) | 2" titanium | 42Hz-
16kHz | 500/1000/2000 | 99dB | 132dB | 20x46x24 | 101.0 |
|
|
The Zx5 is a 15-inch, 2-way cabinet with the most elegant high-impact composite enclosure, featuring the newest generation of EV components: the all-new DXV3150, 500W, 15-inch woofer and the all-new 2-inch neodymium ND2 compression driver. The Zx5 is rated for 600 watts long-term power handling and is able of producing high SPLs whilst providing a very smooth frequency response. With two available coverage patterns (60-degrees x 60-degrees or 90-degrees x 50-degrees), two adjustable monitor angles (45- or 55-degrees) and ten built-in rigging and suspension points allowing for a variety of mounting accessories, the Zx5 fits a variety of applications: installations of individual speakers or clusters in entertainment, cultural or religious venues, as well as on stages with bands, musicians and P.A. rental companies. Specifications Frequency Response (-3dB) 52 - 16000 Hz Recommended High-Pass Frequency 36 Hz Sensitivity 1W/1m 98 dB Max. SPL / 1m (calc); full space 132 dB Coverage (nominal -6dB) H° 60 ° Coverage (nominal -6dB) V° 60 ° System Power Handling (continuous/program/peak) 600/1200/2400 Watts Crossover Frequency 1500 Hz Nominal Impedance (Passive) 8 Ohms Minimum Impedance 6.5 Ohms Input Connections Four-pin Speakon (2) Chassis Size 15 inches Weight Net 22.5 kg ( 49.6 lbs ) Dimensions (HxWxD) 692 x 446 x 411 mm (27.24" x 17.56" x 16.18“) |
EV\'s Rx Series loudspeakers have become the go-to systems for contractors, regional sound companies, and anyone who wants to step up to high-end pro audio without blowing the budget. With integrate L-track rigging points on top and bottom, the Rx cabinets are easy to fly. The unique, asymmetrical, fully rotable horn provides a 15-degree down angle to ensure HF coverage where needed, while avoiding acoustic spill. EV\'s powerhouse DH7 large-format driver (3" voicecoil, 1.4" exit) provides the HF engine, while a selection of EV\'s DL and EVZ woofers anchor the LF and sub frequencies. EV\'s combination of high-level components and unique design make the QRx Series one of the best and most versatile values in the industry.
15-inch two-way, full-range loudspeaker system with 450 watts continuous, 1,800 watts peak power handling. Can be easily biamped with 400 watts LF and 75 watts HFcontinuous DH73-inch voice coil compression driver on an asymmetrical 75-? x 50-? fully rotatable constant-directivity horn. In factory-delivered position the horn provides a 15-?up/35-? down vertical coverage pattern. The fully rotatable horn means that regardless of cabinet position, pattern control is fully user-determined Five-sided cabinet design allows this main PA system cabinet to easily conform to duties as a floor monitor, as a front-of-house system or to be tucked tightly against a ceiling for low-profile applications. Available in black or white. 18-ply, void-free plywood enclosure comes equipped with metal stand mount, L-track rigging on the top and bottom and a single-stud pull-up point on the rear of the enclosure for use flexibility Ring-Mode Decoupling for beautifully detailed vocals and smooth midrange performance |
Description:
The SX18 is a switchable 3 way active, 2 way passive, arrayable loudspeaker. Designed to be used as the main enclosure for small to mid-sized venues or as a supplemental cabinet for large scale sound reinforcement, this enclosure provides high sound pressure levels in a small, lightweight package. Adamson?s Proprietary Kevlar drivers and internal crossovers are employed throughout the SX18 enclosure and its integral fly hardware makes installation of the product fast and effective. Moving the SX18 is easy and efficient with the supplied dolly board. A flexible, high powered enclosure, the SX18 is suited for a wide variety of applications.
Applications:
Live Concert Reproduction
Side Fill Monitoring
Near Field Applications
Theatres
Houses of worship
Dance Clubs
Features:
Kevlar 18" bass and 10" midrange Drivers
1.5" High Frequency Compression Driver
2-Way Bi-Amp/3-Way Tri-amp Operation (selectable)
Adamson Acoustic Waveguide
Integrated Fly Points
Supplied Dolly Board
Durable, Dual Component Finish
Honeycomb Punched, Steel Grille
Roadworthy Construction
Weight: 67 kg
|
Reviews
There are no reviews yet.