PEAVEY PVI8500 Powered Audio Mixer 400 Watt

459.00 incl. GR VAT

In stock

EAN: N/A
Installments calculation
CompareAdd to wishlist Submit Better Price
Availability: Upon Request Upon Request SKU: 534.PVY.001.8500 Category:
FLS Feedback Locating System Master Mute for channels 1-7 Footswitchable effects defeat Combination XLR and 1/4 input jacks RCA, 1/8″ Media input Selectable 9-Band Graphic EQ with FLS Selectable Main or Monitor dual power section RCA Record outputs LED Meter bridge Digital effects parameter control Power amp sub-sonic filtering On-board 24- bit digital effects with […]

 

Read more

  • FLS Feedback Locating System
  • Master Mute for channels 1-7
  • Footswitchable effects defeat
  • Combination XLR and 1/4 input jacks
  • RCA, 1/8″ Media input
  • Selectable 9-Band Graphic EQ with FLS
  • Selectable Main or Monitor dual power section
  • RCA Record outputs
  • LED Meter bridge
  • Digital effects parameter control
  • Power amp sub-sonic filtering
  • On-board 24- bit digital effects with mute button
  • Clip light and signal present indicator
  • Kosmos-C
  • Main line level 1/4″ output
  • Mid-Morph EQ
  • DDT Speaker protection circuit
  • 48 Volt Phantom Power
  • Bluetooth? streaming audio
  • Weight Unpacked: 10.44 kg
  • Weight Packed: 11.8 kg
  • Width Packed: 35.56 cm
  • Height Packed: 55.88 cm
  • Depth Packed: 34.925 cm
Weight 10.44 kg

Reviews

There are no reviews yet.

Be the first to review “PEAVEY PVI8500 Powered Audio Mixer 400 Watt”

Your email address will not be published. Required fields are marked *

Quick Comparison

PEAVEY PVI8500 Powered Audio Mixer 400 Watt removeECLER AC-6 Professional Mixer 8 Channels removeDYNACORD POWERMATE 600-3 COMPACT POWER MIXER.2X340W-4ohms 3 years warranty removeBEHRINGER PMP4000 Europower Powered Mixer 2 x 300W 8 ohm 16 channel removeAllen & Heath Xone:92 4ch Professional DJ Mixer removePEAVEY PVi-8B Plus 9 CHANNEL POWERED MIXER 500 Watt remove
NamePEAVEY PVI8500 Powered Audio Mixer 400 Watt removeECLER AC-6 Professional Mixer 8 Channels removeDYNACORD POWERMATE 600-3 COMPACT POWER MIXER.2X340W-4ohms 3 years warranty removeBEHRINGER PMP4000 Europower Powered Mixer 2 x 300W 8 ohm 16 channel removeAllen & Heath Xone:92 4ch Professional DJ Mixer removePEAVEY PVi-8B Plus 9 CHANNEL POWERED MIXER 500 Watt remove
Imagebehringer pmp4000 powered mixer κονσολα αυτοενισυόμενη artsound
SKU534.PVY.001.8500AC-6E004223E005338144.049534.PVY.001.8B.PLUS
Rating
Price 459.00 incl. GR VAT1,776.92 incl. GR VAT 2,000.00 incl. GR VAT 555.00 incl. GR VAT 1,731.00 incl. GR VAT 449.00 incl. GR VAT
Stock

In stock

Available on backorder

Available on backorder

In stock (can be backordered)

Available on backorder

In stock

AvailabilityIn stockAvailable on backorderAvailable on backorderIn stock (can be backordered)Available on backorderIn stock
Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
Content
  • FLS Feedback Locating System
  • Master Mute for channels 1-7
  • Footswitchable effects defeat
  • Combination XLR and 1/4 input jacks
  • RCA, 1/8" Media input
  • Selectable 9-Band Graphic EQ with FLS
  • Selectable Main or Monitor dual power section
  • RCA Record outputs
  • LED Meter bridge
  • Digital effects parameter control
  • Power amp sub-sonic filtering
  • On-board 24- bit digital effects with mute button
  • Clip light and signal present indicator
  • Kosmos-C
  • Main line level 1/4" output
  • Mid-Morph EQ
  • DDT Speaker protection circuit
  • 48 Volt Phantom Power
  • Bluetooth? streaming audio
  • Weight Unpacked: 10.44 kg
  • Weight Packed: 11.8 kg
  • Width Packed: 35.56 cm
  • Height Packed: 55.88 cm
  • Depth Packed: 34.925 cm
Although the origins of the company date from 1965, ECLER presented its first mixer back in the 70s: the A4, a simple 4 channel mixer oriented to Super 8 film sound edition. The company grew in the 70s with the boom of disco and tourism. The AC-4 was a high fidelity mixer designed to meet the most demanding sound requirements in discos, theatres, cinemas, recording studios, conference rooms... The electronic circuits and the extreme selection of all components and transistors used, made the AC-4 a professional high quality mixer. The new AC-6 is a tribute to those old school, simple, robust, reliable and great sounding mixers. The AC6 enables a new generation of DJs to enjoy the unique sound of those legendary mixers.DYNACORD POWERMATE 600-3 COMPACT POWER MIXER.2X340W-4ohms Original 3 years warranty of Greek distributor This extremely compact powered mixer is the youngest member of the PowerMate3 family. With a total output of 2,000 watts, it is far and away the most powerful compact mixer on the world market, yet it weighs only 9kg! With its very lavish feature set and exemplary versatility it is the ideal choice for all professional applications in which few channels yet very high audio quality are required. Performance without compromises: intuitively operated mixing section; 2 editable digital effects devices with 100 presets each and 20 user memories each; professional 4xIN / 4xOUT digital interface (USB) for the connection of a PC or Mac; stereo equalizer in the master section; large, contrast-rich OLED display; and a class-D high-performance power amplifier delivering 2 x 1,000 watts RMS into 4 ohms. Exclusively high-quality brand components have been used; all faders and potentiometers are supplied by ALPS. In the mixer section, a total of 8 channel strips are available: 4 MIC / LINE channels, 2 MIC / Stereo USB channels ('Super Channels') and 2 stereo LINE channels. The MIC / LINE channels offer extremely low-noise and low-hum electronically balanced XLR microphone inputs with an extremely low distortion factor (typ. < 0.002%) for the connection of low-impedance microphones. For condenser microphones, phantom power (+48 volts) is centrally switchable. The LINE inputs are also electronically balanced and implemented as jack sockets. In addition to a Gain control, a highly efficient 3-band equalizer, an FX send, an AUX send and a MONitor send as well as either Panorama or Balance controls are available. The four MIC / LINE channels boast, in addition, a switchable 80Hz Lo-Cut filter, whilst the Super Channels 5-6 and 7-8 are supplied by the USB inserts 1-2 and 3-4, in each case in stereo. The STEREO-LINE channels (9-10 and 11-12) offer electronically balanced jack inputs for the connection of electronic instruments such as keyboards, drum-computers, guitars and basses with active electronics, as well as all other high-level stereo signal sources such as additional mixers, effects devices etc. CD or MP3 players can be connected to the additional cinch (RCA) inputs CD 1-2 and CD 3-4, which are switched in parallel. The tone controls and sends are identical to those of the MIC / LINE channels. In all input channels, a Signal / Peak LED is provided to assist level control. The SIG LED illuminates at around 30 dB and the PK LED at 6dB beneath the distortion threshold. A MUTE button and a PFL button (in channels 5-12 in stereo) are further features found in all input channels. The DIGITAL AUDIO INTERFACE supplies two stereo channels, present as USB 1-2 and USB 3-4 in Super Channels 5-6 and 7-8 respectively. This interface is implemented professionally in 24-bit resolution and supports sampling rates up to 96 kHz, thereby satisfying studio requirements. The USB sends are supplied with the Master L and R, AUX and MON signals. The DIGITAL AUDIO INTERFACE can be used for input and output simultaneously. Via the USB 2.0 port of your PC / Mac, four channels can be transmitted simultaneously in each direction. When a USB 1.1 interface is used, two channels can be transmitted simultaneously in each direction. The PowerMate is designed for the level of standard PCs / Macs; the gain level can easily be adjusted, if need be, from the computer connected. Included in the delivery is a DVD containing the professional recording software Cubase LE and PC / Mac USB drivers. PC MIDI Interface The PowerMate also makes available a fully-featured PC MIDI interface. The MIDI input also supports the remote switching of both internal effects units using a master keyboard or MIDI footswitch. In the PowerMate's Master Section are to be found the Master A L+R sends (on separate faders), an additional Master B send (switchable pre/post and mono/stereo), the stereo effects returns, and the send signals of the AUXiliary and MONitor busses. If the AUX buss is not used to supply FX 2, it can be switched pre or post and thereby used as an additional monitor send or to supply an external effects device. The 9-band stereo equalizer in the master section allows you to adjust the frequency response to the acoustics of the room. The REC SEND and USB OUT controls determine the level of the master L+R signal at the Rec Send sockets and in the output channels of the digital USB interface. The control below it allows you to adjust the volume in the headphones. Two ten-LED meters provide an overview of the power amplifier level. When the PFL switch is activated, the left-hand LED chain shows the internal level of the master buss in dBu. The STANDBY switch mutes all outputs. For the playback of things like interval music, the DEVICE SETUP menu allows you to route stereo channel 11-12 for standby operation directly to the power amplifiers. The PowerMate is equipped with two very high-quality, 24-bit stereo effects processors, FX 1 and FX 2; these function independently and can therefore be mixed. The two effects units are fully identical in design. Each effects section offers 100 presets including high-quality reverb, delay and modulation effects selected by means of the display. When a delay effect is active, the delay time can be synchronized to the beat of the music using the TAP key. The further possibility exists of modifying individual parameters of the presets and storing the results in the 20 user memories provided. Both effects units are supplied by the FX Send buss. Using the DEVICE SETUP menu, you can, if you wish, configure the AUX send buss to function as an FX 2 send, so that only the FX 1 effects unit is supplied by the FX 1 buss. In this way, the two effects devices can be controlled independently of one another. The effects can be mixed separately in the master and monitor busses. The large, high-contrast OLED display is easily read from a wide range of viewing angles—even in very bright surroundings. The operation of the effects units and processing menus is intuitive and made easier still through the use of soft keys and a rotary encoder. Processing Menus: Particularly valuable in making it possible to adjust the PowerMate perfectly to the selected loudspeaker cabinets, thereby optimizing the audio performance and maximizing the operating safety and reliability of the system, are the LPN Processing and Speaker Protection menus. LPN processing Typical small to medium-sized loudspeaker cabinets, for physical reasons that have nothing to do with their make or quality, exhibit distortion in the transient response of the woofer. Since neither graphic nor parametric equalizers can do anything to alleviate this problem, the PowerMate offers a configurable LPN (low-pass notch) filter. Depending upon the size of the loudspeaker cabinet being used and also to adjust to problematic acoustics (such as those of bassy, boom-ridden rooms), the LPN filter can be set to either High or Medium. The result is considerably greater punch (e.g. from the bass drum), an extension downwards of the frequency response, and improved transparency in the bass and midrange. Speaker Protection This menu allows you to match perfectly the continuous power output of the PowerMateʼs power amplifiers to the connected loudspeakers in the interests of greater operational safety and reliability. Through dynamic limiting of the maximum power at the output, loudspeaker damage due to thermal overload can be avoided, without the wide dynamic range of the power amplifiers being sacrificed. For this purpose, the maximum permissible nominal power handling of the connected loudspeaker cabinet can be selected from the menu. Unlike the case with conventional voltage limiters, dynamic peaks of short duration are permitted, as loudspeaker cabinets can as a rule tolerate peak levels many times higher than their nominal sustainable loads (RMS). The speaker protection supervises permanently the amount of energy being fed to the loudspeakers, only limiting it in the event of a threatened overload, and even then, doing so softly and inaudibly. For peak levels of short duration, the full output of the power amplifier remains available at all times, even when relatively small cabinets are being used. As a result, not only is the maximum dynamic range of the system maintained but also, and at all times, the highest degree of operational safety and reliability. Professional Digital High-Performance Power Amplifier The PowerMate is equipped with a professional, extremely powerful, stereo power amplifier that uses modern and highly efficient class-D technology for audio performance of the highest quality. What this means is that at a nominal output of 2 x 1,000 watts RMS into 4 ohms (or 2 x 1,350 watts RMS into 2.7 ohms) only a comparatively small amount of heat is generated within the device, which therefore consumes considerably less electricity than a conventional power amplifier. The minimal load impedance at the output is 2.7 ohms, making operation with up to three 8-ohm loudspeaker cabinets per channel, connected in parallel, possible with no problems. The overall power supply is handled by an extremely stable, microprocessor-controlled, switching power supply, bringing massive gains in terms of weight-saving over a conventional toroidal transformer. Another advantage is the automatic mains voltage switching, which ensues that the PowerMate can be used without any problem anywhere in the world. Voltage surge protection is also integrated. A ʽsoft startʼ function prevents the mains fuse tripping when the device is switched on. The PowerMate is equipped, naturally, with all the protective circuitry familiar from DYNACORD power amplifiers and satisfies even the extreme demands of hard tour use. The power amplifiers are protected against thermal overload, short-circuit, back EMF and no-load operation as well as high-frequencies or DC at the output. Both outputs, here, are supervised independently so that, should a fault occur, only the channel affected is shut down. When the device is powered up, there is a delay before the power outputs are connected, to obviate the risk of noise. The thermal stability of the PowerMate is assured by two very quiet fans the speed of which is continuously variable. The front-to-rear airflow allows the device to be used in large or small racks. Furthermore, the PowerMate is equipped with an intelligent thermo-limiter, so if ever the threat of overheating does arise, the clip limiter intervenes in a highly musical way, acting only upon the peaks. In this way, a total shutdown of the power amplifiers is effectively prevented, as is any obtrusive fall in the overall volume level. The PROTECT and LIMIT LEDs on the front panel indicate the current operating state of the power amplifiers. To ensure safe transportation, the PowerMate 6003 is supplied with a solid plastic lid that is held in place simply and securely, without the need for any locking mechanism, by magnets. Available as an optional accessory, the carrying bag BAG-600PM not only accommodates the PowerMate with its lid but also offers an additional compartment for cables etc. For rack installation, the RMK-PM600-3 rack-mount kit is available as an option. Order No. F01U213899 (DC-PM600-3-UNIV) Channels (Mono + Stereo) 4 + 4 Auxiliarys (MON, FX, AUX) 1 Pre, 1 Post, 1 Pre/Post switchable Maximum Midband Output Power, 1 kHz, THD = 1%, Dual Channel into 4 Ohms 2 x 1000 W Power Requirements (SMPS with auto range mains input) 100 V to 240 V AC, 50 Hz to 60 Hz Power Consumption, at 1/8 maximum output power, 4 Ohms 450 W Dimensions with lid (W x H x D), mm 438.8 x 161.7 x 362.5 Net Weight, without lid 9.0 kg complete specifications see download section, Datasheet EDS User's ManualEUROPOWER PMP4000 1600-Watt 16-Channel Powered Mixer with Multi-FX Processor and FBQ Feedback Detection System

General

At first glance, this might look like just another one of the many simple 16-channel mixing consoles out there, but with such plentiful functionality, Behringer has succeeded in creating a console is anything but average. The internal amplification module delivers enough power to drive two full-range speakers at 8 ohms. With an impedance of 4 ohms, you can get a lot more volume with only one unit, as you can connect two 8-ohm PA speakers to one output, and two 8-ohm floor monitors to the other.

Behringer Europower PMP4000: Feedback Detection System

Furthermore, the mixer has a number of convenient functions such as a feedback detection system, an equalizer for adjusting the timbre, and an FX processor for adding your personal touch to specific channels.This really is a complete system that offers just about everything you need to provide good amplification for a band. None of that dilly dallying with effects tracks, especially if you don't have room for that in small locations.
  • Ultra-compact 2 x 800-Watt stereo powered mixer (1600-Watt bridged mode)
  • Revolutionary Class-D amplifier technology: enormous power, incredible sonic performance and super-light weight
  • Ultra-compact design at nearly half the weight of conventional powered mixers
  • 16-channel mixer section features 8 mono and 4 stereo channels plus separate CD/Tape input/output
  • Studio-grade 24-bit stereo FX processor with 100 awesome presets including reverb, chorus, flanger, delay, pitch shifter and various multi-effects
  • Revolutionary FBQ Feedback Detection system instantly reveals critical frequencies for easy feedback removal
  • 8 high-quality XENYX Mic Preamps with switchable +48 V phantom power for condenser microphones
  • Effective, extremely musical 3-band EQ, switchable Low cut filter, and Clip LEDs on all mono channels
  • Stereo 7-band graphic EQ allows precise frequency correction of monitor or main outputs
  • Voice Canceller function removes singerʼs voice from recordings for karaoke applications
  • Selectable stereo (main L/R), double mono (main/monitor) or bridged mono amplifier operation mode
  • Breathtaking XPQ 3D stereo surround effect for more vitality and enhanced stereo image
  • Adjustable stereo CD/Tape input for connecting external signal sources
  • Multi-functional stereo Preamp outputs for added flexibility
  • Internal switch-mode power supply, noise-free audio, superior transient response and very low power consumption
  • High-quality components and exceptionally rugged construction ensure long life
  • Conceived and designed by BEHRINGER Germany
  The new BEHRINGER PMP Powered Mixers (2 x 800-Watt stereo, 1600-Watt bridged mode) produce even more power than their predecessors while maintaining a famously low weight and high efficiency. These mixers employ Class-D technology including a new switch-mode power supply, significantly reducing weight and heat. The 20-channel PMP6000 features 12 built-in XENYX preamps, the 16-channel PMP4000 features 8 built-in XENYX mic preamps, and the 10-Channel PMP1680S features 8 high-quality built-in mic preamps. All three models feature 24-bit FX processors and FBQ Feedback Detection. What is Class-D Technology? Instead of operating relatively continuously like Class AB circuits, Class-D amps switch on and off thousands of times per second, delivering power only when needed. In other words, the amplifier is either fully on or fully off , which significantly reduces power losses from the output devices given off as heat. Less heat means our amps donʼt need massive heat sinks, and that means we can make them lighter. Our no-compromise design means the new PMP mixers will deliver full power with incredible fidelity all night long, without the need for lengthy rest cycles. When used in conjunction with switching-mode power supplies, which donʼt require huge and heavy transformers, our Class-D amplifiers provide tremendous dynamic punch and superior fidelity. The resulting speaker systems are much lighter, making them easy to transport and set up. Massive Mono or Stunning Stereo Our latest PMP give you the choice of 2 x 800-Watt stereo, 2 x 800-Watt dual mono mode (giving you a mono version of the main signal through one powered output plus a mono version of all monitor send signals through the second powered input) or 1,600-Watt bridged mono sound. Whether the center of attention happens to be a folk trio, a speech, or a synth-rock band with mind-boggling stereo patches, PMP mixers can accommodate. This sonic versatility also makes it an excellent choice for churches, where vocals and stereo recordings often share face time. Small, Simple, Superb Medium-sized events call for a lightweight (PMP6000: 13.1 kg/ 28.9 lbs; PMP4000: 0.4 kg/22.9 lbs; PMP1680S: 9.9 kg/28.8 lbs), easy-to-use powered mixer. BEHRINGER powered mixers are the most efficient, affordable mixers for the job, and are even suitable for use as pure analog mixers or as pure power amplfiers. With new technological advantages and incredible built-in features, itʼs easier than ever to lend exceptional sound quality to all kinds of public performances.

Product features

  • 19 inches no
  • Number of auxiliaries 1 - 2
  • Number of microphone inputs 5 - 8
  • Number of mono channels 8
  • Number of stereo channels 4
  • Number of submasters 2
  • Compressor on the inputs no
  • Equalizer 3-band, Master EQ
  • Built-in protection peak limiter, clip indicator
  • Built-in effects yes
  • Panning per channel yes
  • Peak power in watts 1,500 - 1,999 watts
  • Connector position front
  • RMS power (4 ohms) 2x 600 W
  • RMS power (8 ohms) 2x 300 W
  • Type of mixer inputs microphone input (XLR), balanced line input (TRS jack), unbalanced line input (RCA), Hi-Z input (TS jack)
  • Type of mixer outputs stereo headphone output (TRS jack or mini jack), lockable speaker output
  • Mixer power power cable
  • Volume control faders

Weight and dimensions including packaging

  • Weight (incl. packaging) 12.9 kg
  • Dimensions (incl. packaging) 56.0 x 53.0 x 21.0 cm

Product specifications

  • compact powered mixer
  • integrated amplifier
  • power at 8 ohms: 2x 300 W RMS, 1x 1,200 W RMS bridged, 2x 400 W max, 1x 1,600 W max bridged
  • power at 4 ohms: 2x 600 W RMS, 2x 600 W max
  • class D amplification technology
  • 8 mono and 4 stereo channels and split CD/tape input/output
  • 24-bit stereo effects processor with 100 presets
  • FBQ feedback detection system
  • 3-band EQ, switchable pad and clip LEDs on every mono channel
  • stereo 7-band graphic EQ for precise corrections of monitor and main outputs
  • voice canceller function for karaoke applications, for example
  • selectable stereo (main L/R), double mono (main/monitor) or bridged mono amplification modes
  • speaker processing function adjusts frequency response to match each speaker
  • standby switch for muting all input channels by signal via the CD/Tape input
  • adjustable stereo aux input for connecting to external signal sources
  • internal power switch-mode supply for noise-free audio
  • dimensions: 122 x 476 x 460 mm
  • weight: 10.4 kg
 
* 6 Dual stereo inputs, 2 with mic inputs * RIAA preamps for up to 4 turntables * Input selectors with 2 colour indicators * Smooth action level controls * 2 Stereo aux sends with pre/post switching * 4 band EQ - high definition of frequency bands, with ʽinfinite killʼ on HF and LF; wide Q for cut, narrow Q for boost * MIDI output from VCF 1+2, crossfader, LFO 2 (MIDI clock), dedicated data control and start/stop button * Large ʽlight-pipeʼ illuminated cue switches * 9 led 3 colour channel ʽbulls eyeʼ LED meters * Crossfader and Filter assign switches * Either smooth travel 60mm VCA faders or rotary VCA faders (Linear or Rotary versions) * Active Penny & Giles VCA crossfader allowing contour to be set from smooth to scratch mix * Cue/Mix monitor balance control * 2 Independent mix outputs * 2 Rotary master level controls * Dual stereo analogue VCF effects * 3 Filter modes combine for more effects * Independent frequency sweep controls * Resonance control for subtle or wild effects * Filter LFO Depth and tempo controls * Illuminated Filter switches punch effect in or out * Powerful headphones monitor with auto cue * Headphones split cue and Aux 1 & 2 monitoring * Stereo music only booth monitor output * Booth mono and mute switching * 9 led 3 colour main ʽbulls eyeʼ LED meters * Balanced +4dBu XLR stereo Mix 1 output * Impedance balanced Line stereo Mix 2 output * Pre-fade recording output Technical Data Outputs: 2 Independent mix outputs Mix 1:Balanced 0dBu XLR stereo Mix 1 Mix 2:Impedance balanced Line stereo Mix 2 output Booth monitor: Stereo music only MIDI output from VCF 1+2 2 Headphone (6,3 mm/ 3,5 mm)The PVi 8B+ powered mixer is easy to use and transport, and is designed with the latest Peavey technology. Constructed with a rugged metal structure, wood cabinet, vinyl surface and protective corners, the PVi 8B Plus is the ideal powered mixer. From packaging to quality control, Peavey produce a products of maximum quality and efficiency with the same specifications you see on other, more expensive powered mixers. “pvi8bplusproduct“
  • 350 watts into 4-ohm (2 x 8 ohm) speakers
  • 8 Balanced microphone and line inputs
  • Tape/CD inputs
  • Reverb level control on each channel
  • Line Out for connection to external amplifiers
  • Monitor output for connection to external amplifiers
  • Return input for connection of external effects processors
  • Record Out for taping
  • RF interference protection on all inputs
  • Switchable 48 volt phantom power for support of electret microphones
  • Footswitch jack for enable/disable effects
  • Effects bus output for connection to external effects processing
Weight10.44 kg4.00 kg9.00 kg13.30 kg4.00 kg17.70 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 10.44 kg
Weight 4.00 kg
Weight 9.00 kg
Weight 13.30 kg
Weight 4.00 kg
Weight 17.70 kg