| Content | Phonic's MAX 860 Power Amplifier provides 600 Watts of power at 8 ohms (bridge mono) or 300 Watts at 4 ohms (stereo) - ideal for clubs, churches, auditoriums and more. Input to the MAX amps is achieved via XLR or phone jack, and output is achieved through either Speakon?-type connectors or binding posts. MAX 860 features ground switches, user defeatable clip limiters, selectable high pass filters, and the option to choose between stereo, parallel and bridge operating modes, making the MAX series amplifiers ideal for real world application.
* Output power: 300W @ 4 Ohms stereo, 200W @ 8 Ohms stereo
* High-current toroidal transformers for greater power and low noise
* Independent user-defeatable peak limiters reduce distortion
* Selectable High-Pass filter at 30Hz or 50Hz
* XLR and 1/4' TRS input jacks
* Binding post and Speakon?-type outputs
* Front mounted gain controls for easy access
* Signal and Peak LED indicators to monitor performance
* Short circuit, thermal, subsonic, RF protection, output DC offset
* Power on/off muting |
Reference Quality Power Amplifier [R-300 Plus] - Controls :
Front : Power on/off switch, attenuator, LED indicator
Rear : Mode seletor switch, Stereo/bridged mono switch - Connectors :
Input : 1 XLR, 1/4" balanced per channel
Output : 5-way binding post and SpeakonTM per channel - Indicators :
Power : Green, Protection : Red, Clip : Red, Signal : Green - Power Source : 100-120VAC or 220-240VAC; 50/60Hz
(supplied AC mains transformer depends on country requirements) - Power Consumption : 250W(2.4A)
- Weight : 8.4kg/18.5lb
- Dimensions (WxHxD) : 482x88x317mm/19x3.5x12.5in
|
XB Series - Intelligent Power
Power Without Compromises.
The XB is designed for paging, music and alarm signals. Versatile, dynamic
and extremely rugged according to IEC286-3. For the highest requirements
in safety and quality.
Sequential power on, alive contacts and incorporated ground fault detection-
the XB is the solution under all conditions. Without the need for additional
equipment. For uninterrupted and troublefree operation.
High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter,
3 ms Muting Delay
PHOENIX / Speakon
LED Indicators for POWER, SIGNAL, CLIP, PROTECT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty
TECHNICAL DATA:
XB 800: 2x 400 W @ 4 Ohm
Class: AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.025%
Signal-to-Noise Ratio: < 103 dB
Channel Seperation: > 85 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Damping Factor: 500 @ 4 Ohm
Cooling: 2x fan (temp. reg. variable speed)
Weight: 13 kg/(29 lbs)
Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)
|
- Rack mount stereo powered monitor speaker system
- New AES/EBU digital input
- lndependent MUTE function
- Sophisticated control panel section
- Ideal where space is at a premium
RM-2 is the ideal solution for monitoring needs in various space-challenged environments such as machine rooms, VTR monitoring, surveillance, mobile and stationary control rooms, theme park applications where audio monitoring is needed and the room for installation is not enough. Adding these new feature sets, RM-2 is now more versatile to various applications. - Stereo analog balanced +4DBu inputs with combo connectors (XLR & 1/4" plug).
- AES/EBU digital input with XLR connector working with fs 44.1kHz to 96kHz.
- Sophisticated control panel section including 26-dot stereo LED meter, biaxial stereo gain control, phone jack, Channel select switch as well as Input select switch.
- Independent MUTE function by holding down CH SEL key for a while.
- Auto Mute when powering on*.
- D-class power amplifier (10W x 2) for clear sound reproduction and light weight construction.
- Multi-voltage power supply.
Speaker Section
- Unit: 110 x 40mm cone type, magnetically shielded, x 2
- Impedance: 8 ohms
- Output SPL: 84 dB/W (1m)
- Frequency response: 200Hz to 20kHz
Amplifier Section
- Rated output power: 10W or more (8 ohms, 1kHz)
- Residual noise: -60 dBV or less (DIN AUDIO)
- Distortion: 0.5% or less (10W / 4 ohms, 1kHz)
Digital input
- Connector: XLR-3-31 type
- Digital input Format: IEC60958 (AES/EBU)
- Digital inputSampling frequency: 44.1kHz to 96 kHz
Analog input
- Connector: XLR / 1/4" combi-jack
- Analog input Nominal input level +4dBu (XLR), -10 DdBV (1/4“)
- Analog input Input impedance 10k ohms or more
Phones
- Connector: 1/4" stereo jack
- Applicable load imp. 8 ohms or more
- Rated output power 20mW + 20mW (32 ohms, 1kHz)
General
- External dimensions: 430(W) x 44(H) x 282(D) mm
- Weight: Approx. 3.5kg
- Power requirement: 100 - 240V~, 50/60Hz
- Power consumption: 10W
|
- Output Power:
500W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD
330W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD
- Bridge Mode, Mono 820W RMS @ 8 Ohms, 1K Hz, 1% THD
- Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)
- Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
- Slew Rate: 15V Per usec
- Damping Factor: @ 8 Ohm: 300
- Impedance: 20 Ohms balanced / 10 Ohms unbalanced
- Cooling System: 2 individual fans
- Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift; Limiter
- build in clip limiter
- Input: XLR 3pin + Jack 6,3mm
- output: Speakon + Binding post
- Dimensions (LxWxH): 360 x 482 x 88mm 2-rack mount spaces
- Weight: 15 KG.
| The LD Systems DP600 Power Amplifier offers an amplifiying level of 2 x 300 W 2 Ohm
The new DEEP2 amp series features four class-H power amplifiers with toroidal core offering amplifying levels from 2 x 400 W till 2 x 810 W at 4 Ohm. During the development of this series we attached a great importance to the reliability and the durability of the amps in continuous operation, this is why we used exclusively high end and selected components for the construction of these products.
The DEEP2 series features a Clip Limiter as well as every common protection circuits. These amps are 2 Ohm and 4 Ohm (bridge) stable in continuous operation. On the rear panel you will find all the common In- and Outputs.
The DEEP2 series will convince every user thanks to a dynamic and very clear sound which is perfectly adapted for Subbass applications as well as for multifunctional speakers. All models are lightweight and feature a robust steel plate housing and a very user friendly and compact design.
The DEEP2 series will prove to be a profitable and reliable choice for bands, renting companies and professional users thanks to its excellent price/performance ratio.
Product type
Power Amplifiers
Rated ouput power (1kHz @ 2 Ohms)
2 x 300 W
Rated ouput power (1kHz @ 4 Ohms)
2 x 400 W
Rated ouput power (1kHz @ 8 Ohms)
2 x 300 W
Rated ouput power (1kHz @ 4 Ohms, bridged)
600 W
Rated ouput power (1kHz @ 8 Ohms, bridged)
800 W
Frequency response
20 - 20000 Hz
Signal-to-noise ratio
105 dB
Protection circuits
clip limiter , DC protection , short circuit , thermal overload
Controls
2 x volume , bridge/stereo mode selector , ground lift , mains switch (on/off)
Indicators
level , Limit , Power , Protect (protection circuit engaged) , Signal
Speaker output connections
Speakon compatible , Terminal posts
Cooling
highly efficient, automatic
Operating voltage
transformer
Operating voltage
230 V AC / 50-60 Hz
Features
Volex mains socket
|
Reviews
There are no reviews yet.