| Content |
Phonic's GEQ1502F is the authentic soundman's choice of EQ - a dual channel 15-band equalizer, offers either 6 or 12 dB of cut or boost in 2/3 octave steps, with standard ISO center frequencies between 25 Hz and 16 KHz. The unit offers both 1/4" and XLR inputs and outputs, and has 4-segment metering on output channels. The GEQ1502F is a single rack space unit and is ideal for both touring and fixed PA installations.
- Low cut filter to remove unwanted low frequency sounds
- Extremely accurate 4-segment LED level meter and input gain control
- Balanced XLR and 1/4" TRS inputs and outputs
- Mono subwoofer output with adjustable crossover frequency
- Shielded toroidal power transformer for ultra low-noise
- Sturdy all-metal chassis
| 1231 Dual 31-Band Graphic Equalizer
The dbx? 12 Series were designed to meet the needs of the most demanding sound reinforcement environments, while offering the simplicity of straightforward controls. The 1231 provides standard features like dual-channels, 31 1/3 octave bands, ISO frequency centers, +/- 12 dB input gain range, and switchable 40Hz/18 dB per octave low-cut filters, but also includes other insightful features. These include 45 mm faders; selectable +/-6dB or +/-15dB boost/cut range for precise gain adjustments; XLR, barrier strip, and 1/4'' TRS connectors for installation ease; balanced inputs and outputs for quiet operation; and chassis/signal ground lift capabilities for quick hum isolation. The visionary design of the dbx 12 Series makes your job easier.
The dbx 12 Series Equalizers were precision engineered to provide years of maintenance-free operation in any application. The magnetically isolated transformer, electronically balanced/unbalanced inputs and servo balanced/unbalanced outputs, RF-filtered inputs and outputs, and power-off hard-wire relay bypass with 2 second power up delay were steps our engineers took to ensure compatibility for all installations. Only the best components were utilized, yielding a 10Hz to 50kHz frequency response, greater than 90dB SNR (ref +4dBu), less than 0.005% THD +Noise (1kHz at +4dBu), and interchannel crosstalk of less than -80dB from 20Hz to 20kHz. All this attention to detail is contained in a 3U steel/aluminum chassis.
SPECIFICATIONS:
| INPUT |
| Connectors: |
1/4" TRS, female XLR (pin 2 hot), and barrier terminal strip |
| Type: |
Electronically balanced/unbalanced, RF filtered |
| Impedance: |
Balanced 40 kOhm, unbalanced 20 kOhm |
| Max Input Level: |
>+21dBu balanced or unbalanced |
| CMRR: |
>40dB, typically >55dB at 1kHz |
| OUTPUTS |
| Connectors: |
1/4" TRS, male XLR (pin 2 hot), and barrier terminal strip |
| Type: |
Impedance-balanaced/unbalanced, RF filtered |
| Impedance: |
Balanced 200 ohm, unbalanced 100 ohm |
| Max Output Level: |
>+21dBu balanced/unbalanced into 2 kOhm or greater
>+18dBm balanced/unbalanced (into 600 ohm) |
| SYSTEM PERFORMANCE |
| Bandwidth: |
20Hz to 20kHz, +0.5/-1dB |
| Frequency Response: |
50kHz, +0.5/-3dB |
|
+/-15dB range |
+/-6dB range |
| Dynamic Range: |
109dB |
115dB |
| Signal-to-Noise: |
90dB |
97dB |
| THD + Noise: |
|
| PRICE WITHOUT V.A.T.
BSS Opal FCS-966 Constant Q Graphic Eq
Graphic equalisers are found in just about every sound application, from room contouring to feedback control and general audio sweetening.
Traditionally, much general eq'ing takes place on the faders alone, but this restricts the use of the faders at each end of the scale for further precision eq work. So we provided the Opal FCS-966 with separate LF and HF contour filters which can change an overall sound balance without disturbing a detailed room or loudspeaker response.
These filters are very musical gentle boost and cut shelving filters which can be used to add (or remove) room effects that change with temperature, audience numbers or humidity.
All these effects can be easily made without disturbing the critical fader settings already made.
Constant Q Filters
The modern generation of graphic eq's
uses the Constant Q topology, pioneered by BSS Audio, which means that the filter width is constant whatever the fader gain setting.
Compared to the earlier 'gyrator' style of filters, Constant Q filters provide a smoother and more predictable interaction between adjacent faders and the resulting eq curve more closely resembles the actual fader positions.
More Gain Control Per Filter
Each eq fader has +/-15dB of adjustable gain, more than many competitive graphic eq's. The faders are long-throw 45mm types for precision control.
High Pass Filter
Also provided on the FCS-966 is a sweepable high-pass filter which can be used very effectively to restrict the low-energy output for better amplifier and loudspeaker performance. Stage monitors also benefit from the application of a high-pass filter to remove bass signals e.g. from vocal-only wedges.
Metering
BSS Audio believes in providing engineers with information, and the FCS-966's 8-segment led meter shows output level and warns of signal clipping within the eq. When the unit is switched to bypass, the meter will read the input level, allowing accurate matching of the 'dry' and equalised signals using the gain control.
Centre Bypass
When any eq fader is in its centre detent position, the filter is automatically bypassed, for optimum performance.
Input/Outputs
All the inputs and outputs of the FCS-966 are electronically balanced, with optional transformer balancing. To make installation of the FCS-966 easier, we've provided three differerent interface connectors: XLR-type, 1/4" TRS jack and Phoenix/Combicon screw terminals.
Relay Bypass
The EQ IN buttons switch the EQ path
into circuit. When switched out, or power fails, a high-quality relay switches the input signal directly to the output connectors.
Control Descriptions
Faders
30 EQ filter faders on ISO centres, each with nominal +/-15dB of gain. Positive centre-detent on 45mm long-throw precision faders.
HP Filter
Sweepable high pass filter, frequency adjustable from OUT (flat) up to 250Hz.
LF Contour
Smooth shelving filter, +/-6dB of gain at 50Hz
HF Contour
Smooth shelving filter, +/-6dB of gain at 14kHz.
GAIN
Used for overall unity gain adjustment. Adjustable from - infinity to +10dB.
CLIP
Triple-point clip detector that indicates red when the internal signal is clipping at any one of three critical points.
LED Meter
Shows output signal level (input signal when eq is bypassed) from -24dBu to +18dBu in 8 steps. |
INPUT
Connectors: 1/4" TRS, female XLR (pin 2 hot)
Type: Electronically balanced/unbalanced, RF filtered
Impedance: Balanced 40k ohm, unbalanced 20k ohm
Max Input Level: >+21dBu balanced or unbalanced
CMRR: >40dB, typically >55dB at 1kHz
OUTPUTS
Connectors: 1/4" TRS, male XLR (pin 2 hot)
Type: Impedance-balanaced/unbalanced, RF filtered
Impedance: Balanced 100 ohm, unbalanced 50 ohm
Max Output Level: >+21dBu balanced/unbalanced into 2k ohm or greater
>+18dBm balanced/unbalanced (into 600 ohm)
SYSTEM PERFORMANCE
Bandwidth: 20Hz to 20kHz, +0.5/-1dB
Frequency Response: 50kHz, +0.5/-3dB
Dynamic Range: Typically >112dB
Signal-to-Noise: Typically >95dB
THD+Noise: |
The class-A circuit used in the EQ-73 is similar to the eq section in the classical 1073 module, without the high pass filter. Additional frequencies have been added and the mid frequency band uses two inductors, the higher value of the second one is used for the two lowest frequencies, 160 Hz and 240 Hz, to achieve a suitable response.
The sound character is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres. The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.
The EQ-73 has stepped frequency controls that offers a wide selection of frequencies from 20 Hz to 24 kHz.
The Low and High frequency bands are shelving and the mid frequency band is of the bell type.
The control range is +/-15 dB for the two lower bands and +/- 18dB for the high frequency band.
There are separate bypass switches for all three bands.
The EQ-73 is made to be used together with one of our PRE-73 models that has an Insert jack. It can also be used with many other units that has a low level insert jack.
Combining a PRE-73 and an EQ-73, and using a UNITE rack kit to mount them together, one will get a 19-inch 1073-style unit at a low cost and with a great sound!
FEATURES
- Vintage Style electronics. No intergrated circuits in the signal path
- 3-band with a dual inductor based mid frequency band
- Stepped frequency selection
- A wide selection of frequencies from 20 Hz to 24 kHz
- Control range up to +/- 18 dB
- Separate Bypass switches for each band
- Tantalum capacitors in the signal path
- Made to be used together with one of our PRE-73 models with an Insert jack or any other unit with a low level Insert jack
- TRS jack for in-and output connection, the nominal working level is around 18 dBu
- Selectable ground lift switch
- External power supply to avoid interaction with the audio circuits
- Great sound that suits most sound sources and genres
- A solid build quality that will last many years of normal use
|
1215 Dual 15-Band Graphic Equalizer
The dbx 12 Series were designed to meet the needs of the most
demanding sound reinforcement environments, while offering the
simplicity of straightforward controls. The 1215 provides standard
features like dual channels, 15 2/3 octave bands, ISO frequency
centers, +/-12 dB input gain range, and switchable 40Hz/18 dB per
octave low-cut filters, but also includes other thoughtful features.
These include 45 mm faders; selectable +/-6dB or +/-15dB boost/cut
range for precise gain adjustments; XLR, barrier strip, and 1/4'' TRS
connectors for installation ease; balanced inputs and outputs for quiet
operation; and chassis/signal ground lift capabilities for quick hum isolation.
The visionary design of the dbx 12 Series makes your job easier.
The dbx 12 Series Equalizers were precision engineered to provide years
of maintenance-free operation in any application. The magnetically isolated
transformer, electronically balanced/unbalanced inputs and servo balanced/
unbalanced outputs, RF-filtered inputs and outputs, and power-off hard-wire
relay bypass with 2 second power up delay were steps our engineers took
to ensure compatibility for all installations. Only the best components were
utilized, yielding a 10Hz to 50kHz frequency response, greater than 90dB SNR
(ref +4dBu), less than 0.005% THD +Noise (1kHz at +4dBu), and interchannel
crosstalk of less than -80dB from 20Hz to 20kHz. All this attention to detail
is contained in a 2U steel/aluminum chassis.
- Switchable boost/cut ranges of ±6 or ±15 dB
- Electronically balanced/unbalanced inputs
- Servo balanced/unbalanced inputs
- RF filtered inputs and outputs
- XLR, Barrier Strip, and 1/4" TRS connectors
- -12dB/+12dB input gain range
- 18dB/octave 40Hz Bessel low-cut filter
- Chassis/signal ground lift capability
- Internal power supply transformer
- Power-off hardwire relay bypass with 2-second power-up delay
|
Reviews
There are no reviews yet.