Content |
Phonic's GEQ1502F is the authentic soundman's choice of EQ - a dual channel 15-band equalizer, offers either 6 or 12 dB of cut or boost in 2/3 octave steps, with standard ISO center frequencies between 25 Hz and 16 KHz. The unit offers both 1/4" and XLR inputs and outputs, and has 4-segment metering on output channels. The GEQ1502F is a single rack space unit and is ideal for both touring and fixed PA installations.
- Low cut filter to remove unwanted low frequency sounds
- Extremely accurate 4-segment LED level meter and input gain control
- Balanced XLR and 1/4" TRS inputs and outputs
- Mono subwoofer output with adjustable crossover frequency
- Shielded toroidal power transformer for ultra low-noise
- Sturdy all-metal chassis
|
The Rane ME 15S microGraphic Equalizer is a two-channel, 2/3-octave design with 20 mm sliders in a single rack space unit. It features a Range switch for high slider resolution in the ±6 dB mode, equivalent resolution to 45 mm sliders found on the DEQ 60L. The ±12 dB mode provides a wide range of control over system audio.
The active filter sections feature Raneʼs innovative constant-Q (constant bandwidth) design. Constant-Q means the bandwidth of each individual filter is guaranteed to be narrow enough to prevent unwarranted interaction between filters, yet wide enough to produce exactly the type of correction curve demanded by even the most unusual acoustic surroundings. This differs dramatically from conventional designs of the past, encumbered with the unfortunate characteristic of changing bandwidth when changing boost/cut amounts.
Front panel controls and indicators include an overall rotary Level control for each channel as well as Overload indicators. Passive pushbutton Bypass switches feature LED indicators, avoiding ambiguity by being on when the unit is Bypassed. (A passive Bypass switch requires no power to operate. This allows completion of the audio path should power fail in the ME 15S.)
Inputs and Outputs are electronically balanced designs, capable of unbalanced operation when required. They accept and drive all possible signal levels into normal load impedances. Balanced applications choose between the XLR or 1/4" Tip-Ring-Sleeve connectors. Unbalanced sources also may tie to the ME 15S through mono 1/4" connectors (no ring connection).
Features - Constant-Q Bandwidth Design
- Overall Level Controls and Passive Bypass Switches
- 20 mm Filter Slide Controls with ±6 dB or ±12 dB Slider Range
- Infrasonic, Ultrasonic, & RFI Filters
- Balanced XLR and 1/4" TRS Inputs and Outputs
- Universal internal switching power supply (100-240 VAC)
|
Phonic's GEQ3102F is the authentic soundman's choice of EQ - a dual channel 31-band equalizer, offering 6 or 12 dB of cut or boost on standard ISO center frequencies between 20 Hz and 20 KHz. The GEQ3102F is 2-rack space units high and accepts both 1/4" TRS phone jacks and XLR connectors, making it ideal for any studio or live venue setup.
- Sweepable high and low cut filters on each channel to remove unwanted frequencies
- Ultra low-noise audio operational amplifiers offer outstanding sound performance
- Relay-controlled hard-bypass with an auto-bypass function during power failure
- Dedicated subwoofer output with user-adjustable low-pass filter
- Feedback detection circuitry for indicating critical frequencies
- Balanced inputs and outputs with 1/4" TRS and XLR connectors
| 1231 Dual 31-Band Graphic Equalizer
The dbx? 12 Series were designed to meet the needs of the most demanding sound reinforcement environments, while offering the simplicity of straightforward controls. The 1231 provides standard features like dual-channels, 31 1/3 octave bands, ISO frequency centers, +/- 12 dB input gain range, and switchable 40Hz/18 dB per octave low-cut filters, but also includes other insightful features. These include 45 mm faders; selectable +/-6dB or +/-15dB boost/cut range for precise gain adjustments; XLR, barrier strip, and 1/4'' TRS connectors for installation ease; balanced inputs and outputs for quiet operation; and chassis/signal ground lift capabilities for quick hum isolation. The visionary design of the dbx 12 Series makes your job easier.
The dbx 12 Series Equalizers were precision engineered to provide years of maintenance-free operation in any application. The magnetically isolated transformer, electronically balanced/unbalanced inputs and servo balanced/unbalanced outputs, RF-filtered inputs and outputs, and power-off hard-wire relay bypass with 2 second power up delay were steps our engineers took to ensure compatibility for all installations. Only the best components were utilized, yielding a 10Hz to 50kHz frequency response, greater than 90dB SNR (ref +4dBu), less than 0.005% THD +Noise (1kHz at +4dBu), and interchannel crosstalk of less than -80dB from 20Hz to 20kHz. All this attention to detail is contained in a 3U steel/aluminum chassis.
SPECIFICATIONS:
INPUT |
Connectors: |
1/4" TRS, female XLR (pin 2 hot), and barrier terminal strip |
Type: |
Electronically balanced/unbalanced, RF filtered |
Impedance: |
Balanced 40 kOhm, unbalanced 20 kOhm |
Max Input Level: |
>+21dBu balanced or unbalanced |
CMRR: |
>40dB, typically >55dB at 1kHz |
OUTPUTS |
Connectors: |
1/4" TRS, male XLR (pin 2 hot), and barrier terminal strip |
Type: |
Impedance-balanaced/unbalanced, RF filtered |
Impedance: |
Balanced 200 ohm, unbalanced 100 ohm |
Max Output Level: |
>+21dBu balanced/unbalanced into 2 kOhm or greater
>+18dBm balanced/unbalanced (into 600 ohm) |
SYSTEM PERFORMANCE |
Bandwidth: |
20Hz to 20kHz, +0.5/-1dB |
Frequency Response: |
50kHz, +0.5/-3dB |
|
+/-15dB range |
+/-6dB range |
Dynamic Range: |
109dB |
115dB |
Signal-to-Noise: |
90dB |
97dB |
THD + Noise: |
|
| Digital stereo active crossover with 4 inputs and 8 outputs, incl. software .
- Flexible routing configurations for all standard mono and stereo output operating modes
- 4 analog inputs and 8 analog outputs (XLR)
- Active frequency filter types (Bessel, Butterworth and Linkwitz-Riley) with slopes up to 24 dB/octave split up the audio signal into different frequency bands
- Incl. software editor (for PC and Mac) for remote control via computer through USB interface: store, transfer, and manage your presets
- Up to 30 user presets storable in the device via software
- 5 menu languages selectable (German, English, French, Spanish, Dutch)
- Alphanumeric LCD screen with 2 lines of 16 characters each
- Input sensitivity digitally adjustable
- Inputs and outputs with 4-digit LED level meter as well as clip and limit LED indicator
- Mute switch with LED indicator per output
- 7-band parametric EQ per output
- Up to 7 ms signal delay adjustable for the outputs
- Output limiter with adjustable limits and automatic attack and release settings as overload protection for your amplifying system
- Switchable phase
- Lock function for prevents undesired changes to settings
- Rack installation, 1 U
- Windows XP, Vista, 7, 10 and Mac OS X 10.5.8 and better
- Digital signal processor
- The device can be connected via USB to the PC in connection with DXO Software
The firmware can be updated via the PC connection
- (19") 48.3 cm rack installation 1 U
Power supply: |
100-240 V AC, 50/60 Hz
6 V DC 800 mA |
Power connection: |
Mains input via Coaxial power connector (M) power supply cord with AC adapter (provided) |
Frequency range: |
10 - 22000 Hz |
THD: |
<0,005 % at 1 kHz |
DSP: |
Digital signal processor |
Crossover frequency: |
20-20000 Hz |
Impedance: |
Input 10 kOhm
Output 50 Ohm |
Gain: |
Output: -50 dB to +12 dB |
Filter: |
Linkwitz-Riley; Butterworth; Bessel; 6db/oct; 12db/oct; 18db/oct; 24db/oct |
Delay: |
0 - 7 ms |
Dynamic range: |
Input: 114 dB
Output: 110 dB |
Sample rate: |
48 kHz |
Connections: |
Input: line via 4 x 3-pin XLR
Output: line via 8 x 3-pin XLR |
Max. level: |
Input: +22 dBu
Output: +9 dBu |
USB port: |
Typ B |
PC connect: |
DXO Software via USB, firmware can be updated |
Housing design: |
(19") 48.3 cm rack installation 1 U |
Dimensions: |
Width: 48,3 cm
Depth: 22,3 cm
Height: 4,45 cm |
Weight: |
1,90 kg |
|
- Professional 15-band stereo graphic equalizer for live and studio applications
- Revolutionary FBQ Feedback Detection system instantly reveals critical frequencies and can also be used as audio analyzer
- Ultra-low noise 4580 operational amplifiers for highest signal integrity
- Dedicated mono subwoofer output with adjustable crossover frequency
- Additional low-cut filter removes unwanted frequencies, e.g. floor rumble
- Highly accurate 4-segment LED output metering and input gain controls for easy level setting
- Servo-balanced inputs and outputs with 1/4" TRS and gold-plated XLR connectors
- “Planet Earth" switching power supply for maximum flexibility (100
- 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving
- 3-Year Warranty Program*
- Designed and engineered in Germany
|
Reviews
There are no reviews yet.