PHONIC MAX-500 Power Amplifier 2Χ120W

Phonic\'s MAX 500 Power Amplifier provides 120 Watts of power at 4 ohms (stereo) in a single rack space - ideal for medium-size venues and for monitoring purposes. MAX 500 features ground switches, and the option to choose between stereo or parallel operating modes. Input to the MAX 500 amp is achieved via XLR or phone jack, and output is achieved through binding posts, making the MAX series amplifiers ideal for real world application.

• Output power: 120W @ 4 Ohms stereo, 90W @ 8 Ohms stereo
• Studio quality performance with very low noise and wide dynamic range
• Class H high efficiency circuitry design
• Ultra-low total harmonic distortion
• High damping factor provides exceptional loudspeaker motion control
• Detented level controls for precise repeatability
• Signal and CLIP indicators to monitor performance
• Protect indicator
• Short circuit, thermal, subsonic, RF protection, output DC offset, over-heat protection and power on/off muting
• Convection cooling system dissipates heat through the heat sink and chassis for noise-free operation
• One rack unit

• Rack mount stereo powered monitor speaker system
• New AES/EBU digital input
• lndependent MUTE function
• Sophisticated control panel section
• Ideal where space is at a premium

• Stereo analog balanced +4DBu inputs with combo connectors (XLR & 1/4" plug).
• AES/EBU digital input with XLR connector working with fs 44.1kHz to 96kHz.
• Sophisticated control panel section including 26-dot stereo LED meter, biaxial stereo gain control, phone jack, Channel select switch as well as Input select switch.
• Independent MUTE function by holding down CH SEL key for a while.
• Auto Mute when powering on*.
• D-class power amplifier (10W x 2) for clear sound reproduction and light weight construction.
• Multi-voltage power supply.

Speaker Section

• Unit: 110 x 40mm cone type, magnetically shielded, x 2
• Impedance: 8 ohms
• Output SPL: 84 dB/W (1m)
• Frequency response: 200Hz to 20kHz

Amplifier Section

• Rated output power: 10W or more (8 ohms, 1kHz)
• Residual noise: -60 dBV or less (DIN AUDIO)
• Distortion: 0.5% or less (10W / 4 ohms, 1kHz)

Digital input

• Connector: XLR-3-31 type
• Digital input Format: IEC60958 (AES/EBU)
• Digital inputSampling frequency: 44.1kHz to 96 kHz
  

Analog input

• Connector: XLR / 1/4" combi-jack
• Analog input Nominal input level +4dBu (XLR), -10 DdBV (1/4“)
• Analog input Input impedance 10k ohms or more

Phones

• Connector: 1/4" stereo jack
• Applicable load imp. 8 ohms or more
• Rated output power 20mW + 20mW (32 ohms, 1kHz)

General

• External dimensions: 430(W) x 44(H) x 282(D) mm
• Weight: Approx. 3.5kg
• Power requirement: 100 - 240V~, 50/60Hz
• Power consumption: 10W

VLP Series Power Amplifier

Output Power:
- 150W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD
- 100W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD
(Bridge Mode, Mono)
- 300W RMS @ 8 Ohms, 1K Hz, 1% THD

Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)

Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz

Slew Rate: 15V Per usec

Damping Factor @ 8 Ohm: 260

Impedance: 20 Ohms balanced / 10 Ohms unbalanced

Cooling System: 2 indivdual fans

Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift

Dimensions (LxWxH): 13.25" x 19" x 1.75" / 336 x 482 x 44mm (1-rack mount space)

Weight: 24 lbs. / 11Kgs.

Special Features: High/Low Pass Filter; Input Sensitivity Selector; Ground Lift

InterM V-1000 Power amplifier 2Χ340W/4ohm, 2Χ180W/8ohm, 2Χ600W/2ohm bridge 1200W/4ohm 10-83kHz

high pass filter 30Ηz & 50Ηz

Solid DYNACORD technology for fixed installations at very competitive prices.
DSA power amplifiers offer a very high, stable output with high efficiency at a high performance level and are therefore the ideal choice for typical fixed installation applications. The connectivity consequently provides Phoenix type in/outs, the input level controls are located on the rear panel, also a switchable high-pass filter (50 Hz, 18 dB/oct) and a Ground Lift switch.
The POWER REMOTE connector makes the task of remote controlling the power amplifier as well as switching it on and off simple. For further remote-supervision and –control possibilities and integration into IRIS-Net networks, an optional remote control module (RCM-810) is available.

The new DEEP2 amp series features four class-H power amplifiers with toroidal core offering amplifying levels from 2 x 400 W till 2 x 810 W at 4 Ohm. During the development of this series we attached a great importance to the reliability and the durability of the amps in continuous operation, this is why we used exclusively high end and selected components for the construction of these products. The DEEP2 series features a Clip Limiter as well as every common protection circuits. These amps are 2 Ohm and 4 Ohm (bridge) stable in continuous operation. On the rear panel you will find all the common In- and Outputs. The DEEP2 series will convince every user thanks to a dynamic and very clear sound which is perfectly adapted for Subbass applications as well as for multifunctional speakers. All models are lightweight and feature a robust steel plate housing and a very user friendly and compact design. The DEEP2 series will prove to be a profitable and reliable choice for bands, renting companies and professional users thanks to its excellent price/performance ratio.