Handheld Audio Analyzer with USB Interface Built-in calibrated measurement microphone 1/3 octave real-time analyzer 31-band EQ setting value display (boost/cut) RT60 measurement Phase checker Noise generator with pink noise, 1kHz and polarity test signal, balanced output Memory and average calculation function SPL meter calibration through sound level calibrator Sound Pressure Level Meter from 30 dB~130 […]
Noise generator with pink noise, 1kHz and polarity test signal, balanced output
Memory and average calculation function
SPL meter calibration through sound level calibrator
Sound Pressure Level Meter from 30 dB~130 dB
Line signal measurement display in dBu, dBV, or Volts (AC)
SPL meter and level meter have three level range selections
Maximum level, Peak hold displays
XLR input and output sockets
USB interface for desktop software control
Audio test signal CD and supporting software
Three power modes: (1) Power Save (2) On (3) Off
Operates seven hours with four AA batteries
AC power adapter included
User's ManualA stage is only as good as its cables — and the AHMCT 8 sets the record straight.
The AHMCT 8 tests the most critical cables on the stage itself and flags up whether they are functioning or not, both visibly via LEDs and audibly via a buzzer. This makes it the perfect tool for engineers — both in the workshop and on stage.
The Pro AHMCT is operated simply, intuitively and safely via a single rotary switch on the device. The sturdy metal housing withstands even tough on-stage demands.
The standard kit comes with two test probes for carrying out fast and simple continuity tests on various cables or installations.
Solid metal housing
Powered by a 9-V block battery
Tests Speakon, XLR, jack/TRS, cinch and midi/DIN cables
Additional continuity tester with measuring probes
Optical display and buzzer
Product type Test Equipment
Connectors 6.3 mm Jack , Banana plug , DIN 5-pin , RCA , Speakon, 4-pin , XLR
Controls down , Power On/Off , up , volume
Indicators battery status , LED chain
Operating voltage 9 V block
Acoustic continuity test yes
Test cable yes
Cabinet material sheet steel
Cabinet surface powder coated
Width 105 mm
Depth 145 mm
Weight 0,64 kg
Details
The all metal DB DISPLAY MKII decibel display from American Audio is great for monitoring your sound volume. It also creates a great lightshow in your amp rack. Make sure your speakers stay in great shape by keeping those dBs under control through this monitoring system.
The LED display progresses from green through amber, to red. There are two different operating modes: Dot or Bar. A 5V power supply is included so you can get the unit plug in an running right away. The DB DISPLAY MKII is perfect a stage, church, club or bar install or for a mobile entertainer.
Specifications
• Designed to set in an amp rack to view your decibel level
• Creates a great light show in your amp rack
• Display progresses from green through amber to red
• Sensitivity adjustment on both left and right channels
• 2 separate modes: dot and bar
• Includes 5V power supply
• Line Inputs: Left & Right RCA / Left & Right XLR
• Line Outputs: Left & Right RCA / Left & Right XLR
• Voltage Operation: DC 5V, 500mA Power Supply included
• Dimensions: (LxWxH): 19” x 1.75” x 1.75” / 44.5mm x 483mm x 44.5mm
• Weight: 2.5 lbs. / 1.25kg.
GP-300 Infrared Thermometer is specially designed to take the body temperature of a person regardless of room temperature.
Features:
Precise non-contact measurements
User selectable ºC or ºF
Selectable Body and Surface temp
Set Alarm value for fever warning
Access to multiple memory values up to 32 records
Trigger lock
Automatic Data Hold & Auto power off
Automatic selection range and Display Resolution 0.1ºC (0.1ºF)
Backlight LCD display
Size 149 x 95 x 44 mm
Weight 172g
CE certified
Specifications
Body Temp range
32.0 to 42.5ºC / 89.6ºF to 108.5ºF
Surface Temp range
0 to 60ºC (32ºF to 140ºF)
Basic Accuracy
In mode of BODY +0.4ºC / +0.7ºF
In mode of Surface +0.8ºC / +1.5ºF
Measuring distance
3~5CM
Response Time
1 sec
Over range indication
LCD will show "HI"/"LO"
Polarity
Automatic (no indication for positive polarity); Minus (-) sign for negative polarity
Emissivity
0.95 fixed value
Spectral response
6~14um
Power off
Automatic shut off after 10 seconds, approx.
Operating Temp.
0ºC to 50ºC (32ºF to 122ºF)
Storage Temp.
-20ºC to 60ºC(-4ºF to 140ºF)
Relative humidity
10%~90% RH operating, <80% RH storage
Power supply
2 x AAA batteries
Cable Tester ACT-100
The Alphaton active remote cable tester can be used for testing either normal short cables or long ones, especially mufticores, wkh connectors not being accessible at one time. The tester is especially suded for fixed installations where cables can not be tested with a standard type cable tester or Ohm meter. Either symmetric and unsymmetric cables can be tested. “Cold" solderings and junction resistances are displayed by color or luminosity changes in three color LED Display. The imprinted fault table incorporates alt important fault conditions, indeed not all possible ones due to their reiatively large number. In case the display is in a state which cannot be found on the imprinted table, it can be looked up in the user's manual. In any case, however, the cabie is in aquite unusable state and should be repaired or replaced.The Alphaton cable tester has a SEND and a REMOTE section. The REMOTE sectionconsistsof two recessed mounted XLR type male or female connector and a stereo phone jack at the right hand side of the tester. Additionally, a separate REMOTE plug is delivered togetherwith the active remote cable tester for testing long cables in fixed installations.
The dbx CT3 is an advanced cable testing unit allowing you to evaluate a large variety of cables with ease. The CT3 offers many common connectors such as RJ45, RJ11, MIDI, Speaker Twist, XLR, RCA Phono, BNC, DIN, TRS, TS, DMX, & Banana. It can be split into 2 parts, a SENDER and RECEIVER so preinstalled and long cables can be tested.
Features
Tests up to 8-pin cables
2 piece chassis for testing installed cables
Test Tone Generator
Allows connection between different format connectors with ease
ʽBananaʼ connector continuity tester with beeper and LED indicator
Super-rugged construction for durability and longer life
(2) DMX (5-pin) connectors for testing of 5 pin->to pin connections
(2) BNC connectors for testing of 2 pin->to pin connections
(2) RCA Phono connectors for testing of 2 pin->to pin connections
(2) XLR connectors (1 x Male, 1 x Female) for testing of 3 pin->to pin connections
(2) MIDI (5-pin DIN) connectors for testing of 5 pin->to pin connections
(2) Speaker Twist connectors for testing of 4 pin->to pin connections
(2) Banana connectors for testing of 1 pin->to pin connections
(2) 1/4” (6.3mm) TRS/TS connectors for testing of 3 pin->to pin connections
(2) RJ45 connectors for testing of 8P8C modular connections
(2) 1/8” (3.5mm) TRS/TS connectors for testing of 3 pin->to pin connections
Specifications
Power Requirements
(2) 9V batteries, one per side (Batteries not included)
Dimensions
3.5” (8.9cm) (W) x 5.5” (14cm) (L) x 1.5” (3.7cm) (H)
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Reviews
There are no reviews yet.