POLK AUDIO PSW 111 Powered Subwoofer 150W

1 x 8 ¨ Dynamic Balance Composite
Cone
Auto On/Off
Port Type Downword Firing
Cont. Power 150watt
Dynamic Power 300 Watts
Dimensions (cm) 30 x 28 x 33

Amplifier Output: 1000 watts (RMS) 2000 watts (Peak)
Frequency Response: 16Hz to 40/160Hz variable
Crossover (Low Pass): 40Hz - 160Hz Variable slope characteristic from
12 - 36dB/Octave
Sub-Sonic Filter (High Pass): 16Hz - 31Hz
EQ: 4 x Presets 1 x User Setting
Equalisation: Graphic 9 band Equaliser ±6dB in 0.5dB steps
Volume Level: -80 - 0dB (1dB increments from 0 to -30dB & 2dB
increments from -31 to -80dB)
Auto Sensing Input Requirements: Line Level>5mV (RMS) Variable delay time
5, 10, 15, 20, 25 & 30 minutes
Variable Phase Control: 0. 45. 90, 135, 180, 225, 270 & 315º
Internal Memory: 3 Independent memory locations
Cabinet Specification:
Sealed Cabinet with 25mm thick M.D.F
construction with critical internal bracing
Amplifier Classification:
Class-D amplifier with DSP control
Driver Complement:
1 x 15" C-CAM long throw sub-woofer driver featuring triple suspension and a 4" long throw voice coil

External Dimensions -
Excluding Plinth: Width: 485mm (19 inches)
Height: 455mm (18 inches)
Depth: 475mm (18 3/4 inches)
Weight: 50 Kg (110lbs)
Mains input Voltage: 100 - 240 Vac 50/60Hz (Factory Set)
Trigger Input:
3.5mm Jack input, +12Vdc = On State

User's Manual

AVAILABLE IN THESE COLOR FINISHES

Dimensions | Metric :16-3/4” W x 16-3/4” D x 16-15/16” H | 42.5 x 42.5 x 43.0 cm
Driver Complement :One high-definition 14" long throw woofer, pressure coupled to two 14” low bass radiators
Frequency Response :11 Hz – 200 Hz
Internal Amplifier Power :1800 watts
Auto On / Off :Signal Sensing (US) | Signal Sensing and Switched (International)
Power Requirements :110 volts Alternating Current (US) | 220 volts Alternating Current (International)
High Level Inputs :Two pairs of 5 way binding posts
High Level Outputs :Two pairs of 5 way binding posts
Subwoofer Inputs :One LFE input (for SW preout only)
Low Level Inputs :Two low level inputs: left and right low level in
Low Level Outputs :Two low level outputs: left and right low level out
High Level High Pass Crossover :Non Variable 6 dB/octave @ 80 Hz: Available only with high level inputs and outputs only
Low Level High Pass Crossover :12 dB/octave continuously variable from 40 Hz to 150 Hz: Available only with low level inputs and outputs
Low Pass Crossover% :24 dB/octave continuously variable from 40 Hz – 150 Hz: Available only with high level inputs and outputs or low level inputs and outputs
Available Finishes :Piano-Gloss Black
Accessories :Rubber feet; Isolation spikes
Fuse :8 amp 250 volt Slo Blo (US) | 4 amp 250 volt Slo Blo (International)
Weight | Metric :97 lbs | 44.0 kg
Warranty :5 Years; 3 Years for Amplifiers

    Pressure vessel enclosure

500W ICEpower® amplifier
Switch mode power supply
Description     Active closed-box subwoofer system
Drive unit     2x f200mm (8 in) mica / aluminium diaphragm long-throw
Frequency range     -6dB at 18Hz and 40/140Hz adjustable (EQ at i)
Frequency response     ±3dB 21Hz – 31/110Hz adjustable (EQ at i)
Power output:     500W
Rated power consumption:     110W (105W - 100V version)
Input impedance:     100kΩ
Signal / noise:     >90dB
Functions:     Volume level
Low-pass filter frequency
Bass roll-off alignment
Auto sense on/standby
Phase switch
Inputs:     Line In (RCA Phono)
Speaker Level In (FCC68 4/4)

System Format: Sealed Cabinet. 25mm M.D.F construction with internal bracing. Sealed amplifier compartment
Low Frequency Limit: 18 Hz
Upper Frequency Limit: 40 - 120 Hz Variable
Low Pass Filter Alignment: Active 4th order 24dB/octave (6/12/18/24 dB user adjustable)
Amplifier Power Output 650 watts Continuous. 1200 watts (peak)
Amplifier Classification D2AudioTM* DSP controlled, Class-D amplifier system. High current switch mode power supply (smpsu)
Equalisation 4 Settings (Off/Music/Movie/Impact)
Phase Control 0-90-180-270 degrees
Auto Sensing Input Level Requirements Line Level > 2mV. Standby after 10 minutes if no signal sensed
Digital Volume Level -60 to +10dB in 1dB increments
Drive Unit Complement 1 x 15” C-CAM® sub-woofer driver featuring triple suspension
3” long throw voice coil
12V Trigger Input 3.5mm mono jack socket
Connections Stereo RCA in/out
LFE in/out
12V Trigger in (3.5mm mono jack)
LEO* - 3.5mm Microphone input jack (microphone supplied)
Input Impedance 20 kohms
Dimensions (H x W x D) 430 x 400 x 400 mm (16 15/16 x 15 3/4 x 15 3/4 Inches)
Grille Depth 28 mm (1 1/8 Inches)
Weight (unpacked) 35.3 kg (77.6 lbs)
Mains Input Voltage 100 - 120 Vac / 220 - 240 Vac 50/60 Hz (Factory preset)
Electrical Certifications CE/CB/ETL/Fcc/ErP (Energy saving compliant)
Power Consumption Maximum 1000W. Standby Fuse Type 20mm UL/VDE (Value is region specific)
IR Remote Control Code NEC SH6122

AVAILABLE IN SIX COLOR FINISHES

The ASW610 subwoofer presents a very happy medium between the more diminutive ASW608 and the all-out power of the ASW610XP. Its long-throw 250mm driver allows the ASW610 to move the large volumes of air needed for high-quality low-frequency output, and its audiophile-standard 200W Class D amplifier keeps the compact unit running cool, even when the music or movie action is whipping up a storm.

In all of the 600 Series subwoofers, the bass driver diaphragms are constructed from a rugged, finely-tuned mix of paper pulp, Kevlar® fibres and resin, which provides the stiffness needed to withstand the tremendous physical forces exerted by the voice coil and pressures inside the cabinet.

Ultra-solid construction delivers slamming bass, drum kicks, and special movie effects. Deformation is minimised; bass precision, power and enjoyment are maximised.