PRESONUS TEMBLOR T-10 Active subwoofer 250W

To hear what's really going on at the bottom of your mixes, you need a subwoofer that speaks the truth. The TemblorTM T10 lets you take charge of the low-frequency foundation of your mix with a combination of quality components and design, plenty of inputs and outputs, and extensive user controls not normally available in this price range.
Main components

• 10-inch glass-composite low-frequency transducer
• Front-firing, bass-reflex acoustic port
  

• Input gain control (-30 dB to +6 dB, continuously variable)
• Continuously variable lowpass filter (50 Hz to 130 Hz)
• Built-in crossover
• Switchable highpass filter removes frequency content below 80 Hz from the full-range signal sent from the T10 outputs to the main monitors
• Momentary footswitch (included) bypasses the subwoofer, highpass filter, and Sub Out
• Polarity invert and ground-lift switch
  

• 250 watt, Class AB amplification
• Internal damping and heat sink
• Integrated, gravity-calibrated rubber feet for stable placement
  

• Left and right, balanced XLR and ¼" TRS and unbalanced RCA main inputs
• Left and right balanced XLR and ¼" TRS outputs 
• XLR subwoofer output for connecting a second T10

Product details

The Sub6 is a large volume cabinet design, equipped with an 11" woofer and a rear laminar port. This configuration guarantees bass linearity whatever the intended SPL. The control board is extremely versatile, with connectivity which allows a 2.1, 2.2 and multichannel use via the L/R inputs and outputs and the LFE. The numerous settings such as the high-pass crossover dedicated to monitors, the adjustable phase and level control provide optimum coupling with the Solo6 Be and the Twin6 Be monitors. And finally, a small, but important point: the footswitch input. It enables one to connect a pedal to deactivate the subwoofer and the high-pass crossovers on the outputs that supply the monitors. This simplifies and greatly improves control during the different stages in monitoring.

10" Subwoofer

Our range of Subwoofers follows our policy of using only high quality components. This has enabled us to bring the best possible products to the market place. We have paid the highest attention to properly extend the frequency range of our speakers and have put even more care into our subwoofer designs. Not only care, but also a lot of testing and abuse.

So you can rest assured that when you buy a TS (ThunderStorm) subwoofer from EVE Audio, you will be getting a first grade product that delivers adequate and precise control over the bass frequencies in your room, without any low-port noise distortion since all TS subwoofers have a passive radiator. Your system will sound as a whole, not just a sum of parts.

All subwoofers feature the powerful accurate and low distortion sound reproduction that is the hallmark of all EVE Audio studio monitors.

Every ThunderStorm subwoofer has detailed controls like switchable satellite filters (full range and 80Hz), phase switch controls (0°, 180°). and variable subwoofer filter frequencies (60....140Hz) to let you tailor and adjust your ThunderStorm to your specific room.

The TS110 model features a very efficient 250W PWM amplifier that drives a proprietary 10" woofer. This guarantees a frequency response of down to 28Hz, up to 300Hz, for a maximum output power of 108 dB (SPL @ 1m) with plenty of power for most needs.

The included remote control will let you adjust not only the subwoofer's volume but also the complete stereo system's volume while sitting comfortably in your sweet spot.

All in all, the ThunderStorm subwoofers will make any system sound better and more complete.

As with every other EVE Audio subwoofer, you get balanced XLR In- and Outputs (Stereo In and Out, LFE In, LFE/Sub Out) for greater convenience.

The particularity of our extremely powerful and accurate subwoofer resides in the passive radiator used that replaces the common bass reflex tube. With this design all audible noise due to air turbulences disappear completely.

Unwanted disturbing pipe resonances (at lambda/2 and multiples) are eliminated, which are unavoidable when applying the principle of a two-sided pipe opening (bass reflex port). The suspension of the passive radiator has a restoring force underneath its tuning frequency and reduces inaudible excursions in the subsonic range. This in turn results in reduced intermodulation distortion in the working range.

The passive radiator allows a particularly low tuning or lower cut-off frequency in a very compact cabinet.

Beef up your studio's low-end response

The LSR310S 200W Powered Subwoofer from JBL is a 200-watt Class-D subwoofer that has been optimized for use in JBL's 3 Series of speakers. The subwoofer is designed for use in music recording, mix, and post-production 5.1 applications. It features a 10-inch speaker and JBL's Slip Stream Port to provide a peak output of 113dB.

A selectable Extended Low Frequency (XLF) effect allows you to augment the low frequency response found in many dance clubs, allowing you use the LSR310S to provide a sonic picture of how your tracks will sound at the club. It also has a selectable input sensitivity and 3 crossover settings including 80Hz, XLF (120Hz), and external, allowing the use of an external crossover.

• 200W Class-D Amplifier
• 113dB Peak Output
• 10" Speaker
• Slip Stream Bass Port
• Balanced XLR Input
• Extended Low Frequency Effects
• 3 Selectable Crossover Settings

Genelec 7071A Active Subwoofer is powerful and precise bass monitoring tool for modern 6.1 or 5.1 channel Surround Sound or traditional stereo systems. With its 19 Hz lower cut-off frequency, high sound pressure output capability and versatile bass management systems, it can be adapted to all low frequency monitoring situations.

The amplifier unit integrated into the cabinet contains active crossover filters, driver overload protection circuits and power amplifiers.

The in-built bass management unit has six signal input and output channels, summed signal output connectors and LFE input equipped with a selectable 85/120 Hz lowpass filter and a 0 / +10dB LFE sensitivity switch.