PRESONUS TUBE PRE V2 microphone PREAMP

At PreSonus, weʼve been designing preamps for a long time, and we always focus on audio quality first. So when we decided to upgrade our popular TubePre V2, we focused on improving an already high-quality sound—without jacking up the price. Like the originalTubePre, the new version is a fully professional tube preamp, with a dual-servo (no capacitors) gain stage that lets you boost the program signal to smoking hot levels without significantly increasing the background noise. Discrete components and high-voltage operation offer dynamic range and detail not found in other single-channel tube preamps in its class.

Housed in a rugged case, the TubePre V2 rear panel sports separate unbalanced, ¼” instrument and balanced, XLR mic inputs and unbalanced ¼” and balanced XLR line outputs. Weʼve included all of the extras you need for professional operation including a high-pass filter, phantom power for condenser mics, polarity reverse switch, and a backlit VU meter.

The PRE-73 MKIII is a one-channel vintage style microphone-, line- and instrument preamplifier. The signal path uses only discrete components like resistors, capacitors and transistors. The in- and output is transformer balanced, using two different transformers, each one optimized for its purpose. This is the way audio components were built before integrated circuits became available.

The circuit used in the PRE-73 MKIII is similar to the preamp section in the classical 1073 module with a corresponding sound character that is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres.
The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.

Features  :

• Vintage Style electronics. No intergrated circuits in the signal path.

• Maximum gain in MIC mode is 80 dB, enough to handle passive ribbon mics with quiet sound sources.

• GAIN switch range 20 - 80 dB. GAIN/LINE mode switch, gain is reduced by 30 dB in LINE mode.

• Selectable two position high frequency AIR boost eq, 3 or 6 dB @ 30 kHz.

• Selectable 6 dB/octave two frequency high pass filter at around 40 (HP1) and 170 Hz (HP2).

• Tantalum capacitors in the signal path.

• Switchable impedance in MIC mode, 1200 or 300 Ohms, will change the tone of most mics. The input impedance in LINE mode is 10 kohm.

• Switchable phantom power and absolute phase.

• A high-impedance instrument input for any sound module, electric guitar or bass.

• A simple but effective 4-step LED output level meter.

• The output level control makes it possible to make fine gain adjustments and also to overload the main gain stage(s) for more character and then lower the signal to a suitable level before the output stage.

• Combo XLR/TRS input jack and separate output XLR and TRS jacks for flexible connections.

• Insert jack for inserting EQ´s and other units.

• Selectable 600 ohm output termination.

• The pcb is prepared for the Carnhill input transformer.

• External power supply to avoid interaction with the audio circuits and transformers.

• A solid build quality that will last many years of normal use.

The MKIII has the following new features compared to the MKII:

• Tantalum capacitors in the signal path.

• Selectable two position high frequency AIR boost eq, 3 or 6 dB @ 30 kHz.

• Selectable two frequency high pass filter, 6 dB/octave at 40 or 170Hz.

• The pcb is prepared for the Carnhill input transformer.

• Revised and less complicated GAIN switch with a separate switch for MIC/LINE selection.

• All GAIN settings can also be used in LINE mode .

The PreSonus HP60 is the most flexible and advanced headphone amplifier system available for professional and project recording studios as well as live sound in-ear monitoring systems. Loaded with six independent,
loud and clear headphone amplifiers, the HP60 features dual stereo inputs as well as external input, for each
channel allowing you to mix between three stereo audio streams (mix A, mix B, and external input). Stereo output is also available on each channel to send line level headphone channel mixes to additional headphone amplifiers or monitor systems. Each channel features headphone level, mix control between A and B inputs, external input volume, mute and mono. The HP60 also features talkback via external XLR microphone input. Common set up of the HP60 in a recording session is to send the main control room mix to input A. Send the click track to input B. Send the each band member direct recording input to each channelʼs external input (more me). This will allow each band member to create a mix between the main mix, the click track and themselves. The HP60 is the ultimate headphone amplification system delivering loud and clear headphone mixes for real-world recording situations.

Features:
-Six independent ultra low noise, high output headphone amplifiers (150 mW per channel)
-Two sets of stereo inputs (A and B) with balanced TRS connectors
-Stereo external input point on each channel for "more me” with trim control
-Mix control between inputs A and B
-Talkback with external XLR microphone with control
-Direct stereo line output on each channel

• Maximum of 66 dB of gain, in eleven discrete steps
• Dynamic range exceeding 120 dB
• 10 Hz to 50 kHz audio bandwidth
• High immunity to RF interference
• High current line output driver
• Transformer-balanced input and output
• Extended range peak limiter via dual opto-isolators makes preamplifier virtually "unclippable“
• Selectable 48-volt / 12-volt phantom power or 12-volt "T" power
• High-pass filter @ 80 or 160 Hz, 6 dB per octave
• Headphone monitoring of microphone audio, monitor audio, or a mix of both
• Monitor input accepts mono, balanced or unbalanced line-level inputs on 1/4-inch tip-ring-sleeve connector
• Separate level control of Monitor gain and overall headphone gain
• Split ear function via DIP switches
• Internal battery power (two-AA)
• Excellent battery life with alkaline and NiMH rechargeable batteries
• External 5-17 VDC powering (plug included)
• High-strength aluminum chassis with durable belt clip

Features
Superlative sound
Studio quality mic preamp
Total control - Input Gain, EQ contour, Output Gain,
Overload indicator
Multiple output connectors
XLR/jack combo input 
Switchable 48 V DC Phantom Power for condenser Mics
Compact, computer friendly package
Needs no external power supply
 
ARX is proud to introduce the e-pre - the ultimate microphone pre-amp for
hard disk recording, designed by audio professionals, not computer engineers.
The all-new e-pre is so much a part of your system that it fits right into a spare
5?" slot in your computer case! It's the perfect tool for all your day-to-day
recording requirements. No equipment racks to plug in, no masses of cabling to
connect - the e-pre is ready and waiting when you need it.
The e-pre is a studio quality microphone pre-amp using the same internal components
as high end mixing consoles, built into a compact, computer friendly package.
It has controls for:
Input Gain - fully variable from 10dB through to 60dB to suit all types of microphones,
plus switchable 48 V Phantom Power to enable condenser microphones to deliver
their best.
A Contour control for EQ sweetening, providing fast, easy access to a whole range
of useful EQ curves
Output level control - fully variable to match the e-pre's output to the input of the sound
card. From -10dB consumer cards through to +4dB for professional sound cards, the
e-pre can handle it.
Multiple output connectors match up with any kind of sound card, including mini jacks,
standard jack, RCA (phono) plugs, and even a connector to link to the internal CD ROM
audio input of your sound card (if fitted).
We've even fitted a 12 VDC input connector on the rear to enable the e-pre to run from an
external power supply if required (eg for use with notebook computers or stand-alone use).

Any way you look at it, the e-pre by ARX is the total professional microphone pre-amp for
all your hard disk recording needs

e-pre Benefits
Professional Balanced XLR mic input
True 48v phantom power
Runs into the Line input of ANY sound card - uses the card you've already paid for
High headroom = clean recordings
Smart EQ
Compatible with non-computer audio equipment
Professional performance and specs in a user friendly package
 

T E C H N I C A L  S P E C I F I C A T I O N S
Input Impedance
Mic 2 K Ohms Balanced; XLR type Pin 1 Audio Ground, Pin 2 +, Pin 3-
Line 25 K Ohms Balanced, ?" TRS jack Tip +, Ring , Sleeve Audio Ground
Phantom Power Voltage Switchable +48 V DC on XLR Pins 2 and 3
Max Input Level Mic +15 dB, Line +20 dB
Input Gain 10 dB Minimum, variable to 60 dB Maximum
Output Level -10 dB variable through 0 dB to +4 dB
Overload Indicator Measured at all Gain points throughout the circuitry
Output Noise -90 dB Unweighted, -97 dB 'A' weighted
(Measured with Gain nominal 20 dB, Output level -10 dB)
Frequency Response 20 - 20 KHz ± 0.25 dB
Distortion
100 Hz 0.0085%
1 KHz 0.008%
10 KHz 0.0083%
(Measured with Mic Gain 20 dB, Output 0 dB)
Power Requirements 12 V DC from either computer supply or external supply
(external power supply not included in e-pre package)
Size 148mmW x 42mmH x 150mm D (5?“W x 1?H x 6“D)
Weight Under 1 Kilo (2.2 lbs)