| Content |
DB1P is a single-channel passive DI BOX equipped with the same type of MU-METAL core transformer used in the DB1A, which provides minimum distortion, linear phase and hum-free transmission also on very long cables. Thanks to the input stage design, DB1P can accept also signals coming directly from the power output of instrument amplifiers, PAD up to 60 dB. A specially designed input filter is also available for cutting any hiss or buzz noise coming from acoustic or electric guitar and basses.
Technical Specifications
|
Type :
|
1 channel passive DI
| |
Width :
|
215 mm(8.465inch )
| |
Height :
|
50 mm(1.969inch )
| |
Depth :
|
125 mm(4.921inch )
| |
Weight :
|
1 kg(2.205lb )
| |
Rack Units :
|
1/2 rack unit.
Removing the two molded sides and attaching two units, with the supplied brackets, you can mount two by two DI boxes into a standard 19¿ rack.
| |
Inputs :
|
Two Parallel 1/4' jack connectors and one parallel RCA connector (unbalanced).
| |
Input Impedance :
|
120 kOhm (pad at 0 dB)
47 kOhm (pad at -20/-60 dB)
44 kOhm (pad at -40 dB)
| |
Input Levels :
|
+15 dBu (pad at 0 dB)
+35 dBu (pad at -20 dB)
+55 dBu (pad at -40 dB)
+75 dBu (pad at -60 dB)
| |
Outputs :
|
XLR male: Pin 2 Hot / Pin 3 Cold / Pin1 Ground
| |
Output Levels :
|
into 1 KOhm or greater
-5 dBu (for 0.1% THD at 50 Hz)
+5 dBu (for 0.1% THD at 1k Hz)
| |
Channels :
|
1 nr.
| |
Frequency response :
|
10 Hz to 100 kHz, +0 dB/-1 dB
| |
Distortion (THD) :
|
| |
S/N Ratio :
|
| |
Controls :
|
Pad -20, Pad -40, Gnd Lift, Filter (12' emulator)
| |
Notes :
|
Insertion loss 20 dB
CMR > 100 dB
Phase distortion 0° at 20 Hz, 0° at 20 kHz.
|
Rear View
|
DOD AC 275 Active Direct Box with Switchable Ground Lift and Attenuator-2nd Hand- The AC 275 is an active, phantom powered direct box. Unlike a passive DI where the frequency response of the signal can be altered depending on the connected impedance, an active DI buffers the input signal with an amplifier. This assures that the sound source will reach the mixer balanced and noise-free. Housed in a cast alloy chassis, the AC 275 supplies two, high impedance, unbalanced 1/4" jacks and one low impedance balanced XLR jack. It operates with battery or phantom power.
Key Features
| ?![]() | Active direct box | ?![]() | Allows a hi impedance unbalanced source to directly feed a low impedance balanced input | ?![]() | Flat frequency response | ?![]() | Connects guitar pickups, microphones or electric instruments to a recording or P.A. console without audio quality loss | ?![]() | Internal pad for speaker level input | ?![]() | Operates with battery or phantom power | ?![]() | Ground lift switch eliminates typical ground loop problems | ?![]() | Rugged, road-proof cast alloy chassis |
| Behringer DI-600P High-Performance Passive Direct Injection Box
Introducing the Ultra-Compact DI-Boxes from BEHRINGER
There are times when you will want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. A direct connection between audio equipment can be a challenge though: technical problems crop up that?ll corrupt the signal.
The DI600P lets you connect instruments or amplifier outputs of up to 3,000 Watts. It converts any unbalanced signal to a balanced signal and eliminates unwanted noise. With its high-performance transformer, it also allows you to use very long cables without the loss of high frequencies.
This is the sort of medicine that?ll cure headaches in your studio or on stage.
It often happens that you want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. The direct connection between audio equipment can quickly turn out to be a real challenge: technical problems crop up that can affect the signal.
Hook Your Guitar or Amp Up to the PA
Be ready for your next gig with the Behringer Ultra-DI DI600P direct box. Designed to send instrument or amplifier signals to the main mixing board, the DI600P is a high-performance passive DI is a useful tool in any gig rig or studio. Dual 1/4" TS jacks are wired in parallel let you plug your instrument into one and use the other as an output to your amp. The balanced XLR mic-level output feeds your mixer a clean and super-flat signal that is true to the source. Sweetwater knows that grounding issues and hum can be a problem at live gigs. The DI600P sports a ground lift switch to kill unwanted ground loops and hum. It also has a filter switch for optimal guitar tone and an instrument/amp switch with a 30dB input level drop. The Behringer Ultra-DI DI600P direct box is an extremely useful tool for any stage rig!
Behringer Ultra-DI DI600P Direct Box Features:
- Compact, high-performance passive direct box
- Jack input 1/4" TS in and parallel out
- Gold-plated XLR output / impedance balanced
- Super-flat frequency output for uncolored sound
- Switchable filter that optimizes the DI for guitars
- Instrument/Amp switch lowers the input level 30dB for feeding amplifiers into the DI
- Instruments or amplifier outputs with up to 3,000 watts can be connected directly
- Offers impedance and signal matching of instruments to mixers
- Perfect for stage and studio use
- Ground lift switch eliminates typical ground loop problems
- Rugged metal case can take the rigors of the road
Get your signal to the board with Behringer\'s Ultra-DI DI600P direct box!
Tech Specs
- Type: Passive DI Box
- Channels: 1
- Ground Lift: Yes
- Inputs: 1 x 1/4"
- Outputs: 1 x 1/4“, 1 x XLR
- Height: 1.4"
- Width: 3.75"
- Depth: 5"
- Weight: 0.66 lbs.
- Manufacturer Part Number: DI600P
| Product Features:
Professional and multi-purpose direct injection box for stage and studio applications
Provides impedance and signal matching for the direct connection of instruments to mixers and amplifiers
Ultra-flat frequency response due to renowned BEHRINGER OT-1 transformer
Internal battery automatically shuts off when phantom power is applied
Allows direct connection to speaker outputs with up to 3,000 Watts
Switchable input attenuation allows input levels of up to +50 dB
Ground Lift switch eliminates typical ground loop problems
¼" TRS and gold-plated XLR connectors
Ultra-rugged, road-suitable aluminum case
Stackable oversized rubber corners
High-quality components and exceptionally rugged construction ensure long life and durability
Conceived and designed by BEHRINGER Germany
With the DI100, you can rest assured that your sound source will reach the console balanced and noise-free. BEHRINGER's take on the all-important active DI box gives you functionality, durability and incredible sound at a remarkable price.
Be Direct
Plug into the DI100's balanced 1/4" TRS or XLR input, then send a signal to your console via the balanced XLR output. You can even plug your guitar or bass amp's speaker output into the DI100, which can handle ratings of up to 3,000 Watts and still deliver a perfect signal. It also features a 1/4" LINK jack to send your signal to an on-stage amplifier. The DI100 also has a switchable attenuation pad, allowing input levels of up to +50 dB. There is also a ground lift switch to eliminate noise associated with ground loops. The DI100 also features BEHRINGER's renowned OT-1 output transformer.
Superior Sound, Incredible Value
DI boxes are an essential part of any stage or studio, and the DI100 delivers the exceptional sound you expect, wrapped up in a rugged, road-proof aluminum case with stackable rubber corners. |
Active DI-Box SM-60
The electronic Direct-Injection Box SM-60 allows direct connection of electronic
music instruments such as keyboards, synthesizers, electric and electronic pianos,
etc. with mixing consoles in PA-systems and in recording studios.
The SM-6 is designed for applications, where a passive DI-Box does not perfom
satisfactorily, i.e., where the output level of a passive DI-Box is too low for the microphone
input section of the mixing desk.
Because the input impedance of the SM-6 is above 5 MOhm, instrument outputs are
not loaded or in any other way adversely affected. The voltage ratio from input to output
is 1: 1 and is always sufficient for connection with any microphone input. Input connectors
are 1/4" phone jacks, output connector is a Switchcraft D3M; output is 600 Ohms,
transformer balanced. The output level may in certain cases overload microphone inputs -
the line input section of the mixing console must then be used for connecting the SM-6.
The unit operates with a 9 V battery or phantom powering from 24 to 48 volts.
Technical Data
input impedance > 5 MOhm
max. input impedance + 6 dBu, 1,55V
ouptut impedance 600 Ohm
frequency response 20 ... 20000 Hz, ± 0,2 dB
gain 1 : 1
THD < 1 % at 30 Hz
< 0,7 % bei 40 Hz
powering 9-V battery (IEC 6LF22) or
phantom power 24 ... 48 V.
inputs two 1/4" phone jacks , unbalanced
(one being used as output to instruments amp)
outputs XLR, balanced
pin 1 = ground, pin 2 = hot, pin 3 = cold
case aluminium die-cast
weight 240 g
dimensions 113 x 71 x 37 mm |
Passive DI box. Jack input with paralell "THRU" output, transformer balanced XLR output. Attenuable input sensitivity, can handle both line level and speaker level signals.
Product type
DI Boxes
Type
passive
Channels
1
Inputs
1
Input connectors
6.3 mm Jack
Max. input level
+ 54 dBu
Input impedance
(@ 60 Hz) 60k Ohm(s)
Input pad
0 / -30 dB
Outputs
1
THRU outputs/channel
1
Output connectors
6.3 mm Jack , XLR
Max. output level
+ 4 dBu
Output impedance
600 Ohm(s)
Frequency response
20 - 20000 Hz
Transformer balanced
yes
Ratio
10 : 1
Controls
attenuator , ground lift
Cabinet material
sheet steel
Cabinet surface
powder coated
Width
110 mm
Depth
73 mm
Height
42 mm
Weight
0,34 kg
|
Reviews
There are no reviews yet.