PROEL DB-1P DI Box Passive one input DI Box with PAD up to 60 dB

Discontinued

29.00 incl. GR VAT

Out of stock

CompareAdd to wishlist Submit Better Price
Availability: Discontinued Discontinued SKU: H30PR00202 Category:
DB1P is a single-channel passive DI BOX equipped with the same type of MU-METAL core transformer used in the DB1A, which provides minimum distortion, linear phase and hum-free transmission also on very long cables. Thanks to the input stage design, DB1P can accept also signals coming directly from the power output of instrument amplifiers, PAD […]

 

Read more

DB1P is a single-channel passive DI BOX equipped with the same type of MU-METAL core transformer used in the DB1A, which provides minimum distortion, linear phase and hum-free transmission also on very long cables. Thanks to the input stage design, DB1P can accept also signals coming directly from the power output of instrument amplifiers, PAD up to 60 dB. A specially designed input filter is also available for cutting any hiss or buzz noise coming from acoustic or electric guitar and basses.

 

 

Technical Specifications

 

Type :

1 channel passive DI

Width :

215 mm(8.465inch )

Height :

50 mm(1.969inch )

Depth :

125 mm(4.921inch )

Weight :

1 kg(2.205lb )

Rack Units :

1/2 rack unit.
Removing the two molded sides and attaching two units, with the supplied brackets, you can mount two by two DI boxes into a standard 19¿ rack.

Inputs :

Two Parallel 1/4′ jack connectors and one parallel RCA connector (unbalanced).

Input Impedance :

120 kOhm (pad at 0 dB)
47 kOhm (pad at -20/-60 dB)
44 kOhm (pad at -40 dB)

Input Levels :

+15 dBu (pad at 0 dB)
+35 dBu (pad at -20 dB)
+55 dBu (pad at -40 dB)
+75 dBu (pad at -60 dB)

Outputs :

XLR male: Pin 2 Hot / Pin 3 Cold / Pin1 Ground

Output Levels :

into 1 KOhm or greater
-5 dBu (for 0.1% THD at 50 Hz)
+5 dBu (for 0.1% THD at 1k Hz)

Channels :

1 nr.

Frequency response :

10 Hz to 100 kHz, +0 dB/-1 dB

Distortion (THD) :

S/N Ratio :

Controls :

Pad -20, Pad -40, Gnd Lift, Filter (12′ emulator)

Notes :

Insertion loss 20 dB
CMR > 100 dB
Phase distortion 0° at 20 Hz, 0° at 20 kHz.

 

Rear View

Weight 0.30 kg

Reviews

There are no reviews yet.

Be the first to review “PROEL DB-1P DI Box Passive one input DI Box with PAD up to 60 dB”

Your email address will not be published. Required fields are marked *

Quick Comparison

PROEL DB-1P DI Box Passive one input DI Box with PAD up to 60 dB removePALMER AUDIO PAN02 TOOLS Active DI-box removeALPHATON SM-60 ACTIVE D.I BOX removeBSS AR-133 ACTIVE DI BOX (Battery/ Phantom Powered) removeBEHRINGER DI100 Ultra DI Box Active Battery/Phantom removeOMNITRONIC LH-060 2-channel DI box/splitter, passive remove
NamePROEL DB-1P DI Box Passive one input DI Box with PAD up to 60 dB removePALMER AUDIO PAN02 TOOLS Active DI-box removeALPHATON SM-60 ACTIVE D.I BOX removeBSS AR-133 ACTIVE DI BOX (Battery/ Phantom Powered) removeBEHRINGER DI100 Ultra DI Box Active Battery/Phantom removeOMNITRONIC LH-060 2-channel DI box/splitter, passive remove
ImageBEHRINGER DI100 Ultra-Rugged DI Box for Stage and Studio Powered active battery phantom
SKUH30PR00202PAN02SM-60AR-133E005264LH060
Rating
Price 29.00 incl. GR VAT 68.20 incl. GR VAT 113.09 incl. GR VAT 159.00 incl. GR VAT 46.00 incl. GR VAT 73.35 incl. GR VAT
Stock

Out of stock

Only 2 left in stock (can be backordered)

In stock

Only 5 left in stock (can be backordered)

In stock (can be backordered)

Available on backorder

AvailabilityOut of stockOnly 2 left in stock (can be backordered)In stockOnly 5 left in stock (can be backordered)In stock (can be backordered)Available on backorder
Add to cart

Read more

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
  • Professional and multi-purpose direct injection box for stage and studio applications
  • Provides impedance and signal matching for the direct connection of instruments to mixers and amplifiers
  • Ultra-flat frequency response due to renowned BEHRINGER OT-1 transformer
  • Internal battery automatically shuts off when phantom power is applied
  • Allows direct connection to speaker outputs with up to 3,000 Watts
Content

DB1P is a single-channel passive DI BOX equipped with the same type of MU-METAL core transformer used in the DB1A, which provides minimum distortion, linear phase and hum-free transmission also on very long cables. Thanks to the input stage design, DB1P can accept also signals coming directly from the power output of instrument amplifiers, PAD up to 60 dB. A specially designed input filter is also available for cutting any hiss or buzz noise coming from acoustic or electric guitar and basses.     Technical Specifications  

Type : 1 channel passive DI
Width : 215 mm(8.465inch )
Height : 50 mm(1.969inch )
Depth : 125 mm(4.921inch )
Weight : 1 kg(2.205lb )
Rack Units : 1/2 rack unit.
Removing the two molded sides and attaching two units, with the supplied brackets, you can mount two by two DI boxes into a standard 19¿ rack.
Inputs : Two Parallel 1/4' jack connectors and one parallel RCA connector (unbalanced).
Input Impedance : 120 kOhm (pad at 0 dB)
47 kOhm (pad at -20/-60 dB)
44 kOhm (pad at -40 dB)
Input Levels : +15 dBu (pad at 0 dB)
+35 dBu (pad at -20 dB)
+55 dBu (pad at -40 dB)
+75 dBu (pad at -60 dB)
Outputs : XLR male: Pin 2 Hot / Pin 3 Cold / Pin1 Ground
Output Levels : into 1 KOhm or greater
-5 dBu (for 0.1% THD at 50 Hz)
+5 dBu (for 0.1% THD at 1k Hz)
Channels : 1 nr.
Frequency response : 10 Hz to 100 kHz, +0 dB/-1 dB
Distortion (THD) :
S/N Ratio :
Controls : Pad -20, Pad -40, Gnd Lift, Filter (12' emulator)
Notes : Insertion loss 20 dB
CMR > 100 dB
Phase distortion 0° at 20 Hz, 0° at 20 kHz.
  Rear View

Standard active DI box. Can be operated with 9 V batteries or 48 V phantom power. High-impedance input; higher output level than with a passive DI box. Active circuitry allows for high input impedance ( 1 meg. ohm) and higher input sensitivity (typical difference between in and out -4 dB). Maximum output impedance with phantom power operation +10 dB. Output: transformer balanced. The special "floating ground" circuitry enables ground lift even during phantom power operation. Metal case 110 x 73 x 42 mm.

Active DI-Box SM-60

The electronic Direct-Injection Box SM-60 allows direct connection of electronic
music instruments such as keyboards, synthesizers, electric and electronic pianos,
etc. with mixing consoles in PA-systems and in recording studios.
The SM-6 is designed for applications, where a passive DI-Box does not perfom
satisfactorily, i.e., where the output level of a passive DI-Box is too low for the microphone
input section of the mixing desk.
Because the input impedance of the SM-6 is above 5 MOhm, instrument outputs are
not loaded or in any other way adversely affected. The voltage ratio from input to output
is 1: 1 and is always sufficient for connection with any microphone input. Input connectors
are 1/4" phone jacks, output connector is a Switchcraft D3M; output is 600 Ohms,
transformer balanced. The output level may in certain cases overload microphone inputs -
the line input section of the mixing console must then be used for connecting the SM-6.
The unit operates with a 9 V battery or phantom powering from 24 to 48 volts.

Technical Data

input impedance > 5 MOhm
max. input impedance + 6 dBu, 1,55V
ouptut impedance 600 Ohm
frequency response 20 ... 20000 Hz, ± 0,2 dB
gain 1 : 1
THD < 1 % at 30 Hz
       < 0,7 % bei 40 Hz
powering  9-V battery (IEC 6LF22) or
                 phantom power 24 ... 48 V.
inputs  two 1/4" phone jacks , unbalanced
          (one being used as output to instruments amp)
outputs  XLR, balanced
             pin 1 = ground, pin 2 = hot, pin 3 = cold
case aluminium die-cast
weight 240 g
dimensions 113 x 71 x 37 mm

With added functionality and enhanced audio performance, the AR-133 has been designed to be more affordable for musicians, studios and PA companies. The unit includes phantom power and battery supplies as standard. Should the phantom power from the console fail or be accidentally switched off, the AR-133 automatically switches over to the internal 9V battery providing uninterrupted use. The unit is housed in a rugged aluminium extrusion case, with robust polyurethane end-cheeks which give the AR-133 a very distinctive look. Input connectors are both 1/4" jack sockets and an XLR socket, the latter meaning that the AR-133 can be used to convert unbalanced signals to a balanced output on XLRs throughout. The arched case allows cables to run back underneath the unit from the end for neat cable management. Input attenuation is 0, -20 or -40dB, making the box suitable for instrument, line or amplifier levels on inputs. On the output side, a ground-lift switch is provided for quick solutions to ground-loop problems. The AR-133 uses an enhanced version of the same audio path as the AR-116, now regarded by many people as a reference standard. The sound quality is legendary, particularly on acoustic and bass guitars. Numerous applications can be satisfied by the AR-133. For example, as well as the traditional guitar use, the AR-133 can be used with keyboards, DJ consoles, amplifier outputs, and other electronic sources.An additional bonus is the ability to use the AR-133 as an active balancing device. Input Section Input Impedance  1M Ohm (pad at 0dB) 47k Ohm (pad at -20dB) 47k Ohm (pad at -40dB) Max Input Level +9dBu (pad at 0dB) +29dBu (pad at -20dB) +49dBu (pad at -40dB) Connectors  Two Parallel 1/4" jack connectors and a parallel XLR connector (unbalanced) Jack:  Tip Hot (+ve) Sleeve Ground XLR: Pin 2 Hot (+ve) Pin 1 & 3 Ground Output Section Output Transformer Balanced Max. Output Level  +8dBu into 600 Ohms or greater Connector  XLR3-32 or equivalent System Performance Distortion (THD)  < 0.005% at 1khz, 0dbu output Noise  < -105db unweighted, 22hz-22khz, rms* Frequency Response 30Hz to 20kHz, +0dB/-1dB General Main/Standby battery 9 volt PP3 type, preferably alkaline. Current drain  on phantom - less than 7.5mA on battery - less than 2mA. Phantom Power  +20 volts DC to +48 volts DC Weight 650 gms, excluding batteries. Overall Dimensions  59 mm x 124 mm x 143 mm (2.3" x 4.9" x 5.6“)Product Features: Professional and multi-purpose direct injection box for stage and studio applications Provides impedance and signal matching for the direct connection of instruments to mixers and amplifiers Ultra-flat frequency response due to renowned BEHRINGER OT-1 transformer Internal battery automatically shuts off when phantom power is applied Allows direct connection to speaker outputs with up to 3,000 Watts Switchable input attenuation allows input levels of up to +50 dB Ground Lift switch eliminates typical ground loop problems ¼" TRS and gold-plated XLR connectors Ultra-rugged, road-suitable aluminum case Stackable oversized rubber corners High-quality components and exceptionally rugged construction ensure long life and durability Conceived and designed by BEHRINGER Germany   With the DI100, you can rest assured that your sound source will reach the console balanced and noise-free. BEHRINGER's take on the all-important active DI box gives you functionality, durability and incredible sound at a remarkable price.
Be Direct
Plug into the DI100's balanced 1/4" TRS or XLR input, then send a signal to your console via the balanced XLR output. You can even plug your guitar or bass amp's speaker output into the DI100, which can handle ratings of up to 3,000 Watts and still deliver a perfect signal. It also features a 1/4" LINK jack to send your signal to an on-stage amplifier. The DI100 also has a switchable attenuation pad, allowing input levels of up to +50 dB. There is also a ground lift switch to eliminate noise associated with ground loops. The DI100 also features BEHRINGER's renowned OT-1 output transformer.
Superior Sound, Incredible Value
DI boxes are an essential part of any stage or studio, and the DI100 delivers the exceptional sound you expect, wrapped up in a rugged, road-proof aluminum case with stackable rubber corners.

2-channel DI box/splitter, passive Converts 2 separate unbalanced line inputs (e.g. instruments) into 2 balanced XLR outputs for connecting a mixer Switchable to split mode (input 1 routes the signal to both outputs) Switchable input attenuation: 0 dB, -20 dB, -40 dB Ground-lift switch eliminates ground loop problems 2 signal inputs via XLR/jack combo connectors 2 low-impedance XLR outputs Modern convex housing design Full rubber housing corners for safe operation Cables can be routed under the housing

Weight0.30 kg0.31 kg0.24 kg0.65 kg0.65 kg0.70 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 0.30 kg
Weight 0.31 kg
Weight 0.24 kg
Weight 0.65 kg
Weight 0.65 kg
Weight 0.70 kg