Content |
DB1P is a single-channel passive DI BOX equipped with the same type of MU-METAL core transformer used in the DB1A, which provides minimum distortion, linear phase and hum-free transmission also on very long cables. Thanks to the input stage design, DB1P can accept also signals coming directly from the power output of instrument amplifiers, PAD up to 60 dB. A specially designed input filter is also available for cutting any hiss or buzz noise coming from acoustic or electric guitar and basses.
Technical Specifications
Type :
|
1 channel passive DI
|
Width :
|
215 mm(8.465inch )
|
Height :
|
50 mm(1.969inch )
|
Depth :
|
125 mm(4.921inch )
|
Weight :
|
1 kg(2.205lb )
|
Rack Units :
|
1/2 rack unit.
Removing the two molded sides and attaching two units, with the supplied brackets, you can mount two by two DI boxes into a standard 19¿ rack.
|
Inputs :
|
Two Parallel 1/4' jack connectors and one parallel RCA connector (unbalanced).
|
Input Impedance :
|
120 kOhm (pad at 0 dB)
47 kOhm (pad at -20/-60 dB)
44 kOhm (pad at -40 dB)
|
Input Levels :
|
+15 dBu (pad at 0 dB)
+35 dBu (pad at -20 dB)
+55 dBu (pad at -40 dB)
+75 dBu (pad at -60 dB)
|
Outputs :
|
XLR male: Pin 2 Hot / Pin 3 Cold / Pin1 Ground
|
Output Levels :
|
into 1 KOhm or greater
-5 dBu (for 0.1% THD at 50 Hz)
+5 dBu (for 0.1% THD at 1k Hz)
|
Channels :
|
1 nr.
|
Frequency response :
|
10 Hz to 100 kHz, +0 dB/-1 dB
|
Distortion (THD) :
|
|
S/N Ratio :
|
|
Controls :
|
Pad -20, Pad -40, Gnd Lift, Filter (12' emulator)
|
Notes :
|
Insertion loss 20 dB
CMR > 100 dB
Phase distortion 0° at 20 Hz, 0° at 20 kHz.
|
Rear View
|
2-channel DI box/splitter, passive Converts 2 separate unbalanced line inputs (e.g. instruments) into 2 balanced XLR outputs for connecting a mixer Switchable to split mode (input 1 routes the signal to both outputs) Switchable input attenuation: 0 dB, -20 dB, -40 dB Ground-lift switch eliminates ground loop problems 2 signal inputs via XLR/jack combo connectors 2 low-impedance XLR outputs Modern convex housing design Full rubber housing corners for safe operation Cables can be routed under the housing |
You're serious about getting rid of all that excess noise on stage, but you've got so many line instruments you don't know where to start. The ADB-4 from Stewart can take care of all your high impedance problems. The ADB-4 is 4 active direct boxes, all in a module that only takes up half a space on your keyboard rack. It's a rugged, durable piece of equipment that packs a lot of DI power.
? Requires phantom power or 9v battery ? Ground lift switch ? Instrument or speaker level switch ? Transformerless ? Can be used with amp up to 400w ? RF shielding | Behringer DI-400P High-Performance Passive Direct Injection Box
Introducing the Ultra-Compact DI-Boxes from BEHRINGER
There are times when you will want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. A direct connection between audio equipment can be a challenge though: technical problems crop up that?ll corrupt the signal.
The DI400P lets you connect instruments or amplifier outputs. It converts any unbalanced signal to a balanced signal and eliminates unwanted noise. With its high-performance transformer, it also allows you to use very long cables without the loss of high frequencies.
This is the sort of medicine that?ll cure headaches in your studio or on stage. |
Passive DI box. Jack input with paralell "THRU" output, transformer balanced XLR output. Attenuable input sensitivity, can handle both line level and speaker level signals.
Product type
DI Boxes
Type
passive
Channels
1
Inputs
1
Input connectors
6.3 mm Jack
Max. input level
+ 54 dBu
Input impedance
(@ 60 Hz) 60k Ohm(s)
Input pad
0 / -30 dB
Outputs
1
THRU outputs/channel
1
Output connectors
6.3 mm Jack , XLR
Max. output level
+ 4 dBu
Output impedance
600 Ohm(s)
Frequency response
20 - 20000 Hz
Transformer balanced
yes
Ratio
10 : 1
Controls
attenuator , ground lift
Cabinet material
sheet steel
Cabinet surface
powder coated
Width
110 mm
Depth
73 mm
Height
42 mm
Weight
0,34 kg
|
Tube-buffered DI-Box DI-1000
The Tube-Buffered DI-Box DI-1000 allows the extraction of all the musical details of musical interfaces without degrading the sound. This can only be achieved by providing a very high input impedance to avoid any loading of instrument pickups.This design approach allows seemingly infinite headroom to preserve the real dynamic range of the interfaced instruments.A vacuum tube enables all these goals to be achieved without any compromises in sound quality.The sonic difference between a standard DI-Box and the Tube-Buffered DI-Box is comparable to the musical resolution difference between a standard microphone and a studio microphone.One of the best transformers, the very transparent sounding JENSEN JT-DB-E, was chosen providing complete ground isolation. The parameters of this transformer, like frequency response, phase response, group delay and geadroom capabilities, play a vital part in the performance of this DI-Box. Technical Specifications Input The signal of the instrument is directly fed to the tube circuit with > 20 MOhms input impedance to prevent any signal degradation, inevitable in traditional designs. Buffered Output“ The second stage of the vacuum tube is used to buffer the signal and lower the output impedance to < 8 kOhms. This unity gain output allows for cable runs of 10 meters without loosing high frequency information. Boost circuit The boost circuit increases the signal send to the output transformer by 15 dB. This may be useful for instruments with extremely low output, but decreases headroom capability to 6 Volt rms. Under these circumstances the signal may be clipped, concerning the output transformer?s signal, which gives you 2nd harmonic tube-like distortion. This distortion normally does not occur - but is sometimes desirable, being the reason for this special feature. Unity circuit The unity circuit feeds a low distortion unity gain signal to the JENSEN output transformer. This gives the best possible sound quality. Ground-lift“-Switch This front panel mounted switch allows complete ground and electrical isolation between the direct injection box and the console or recording device.
Mechanical Specifications Cabinet 2 mm stainless steel Front- and rear-panel 1,5 mm stainless steel lasercut and photo-chemically etched Dimensions 185 x 100 x 40 mm Vibration insulation 4 high-compliance rubber-elements Operating Voltage 220/110 V AC, selectable via rear panel mounted switch. The fuse is easily accessible from the rear panel. IEC mains connector with optional fixture. Construction details Double sided glass fibre contacted PCB with 70 mm copper plating. 1% metal film resistors and the finest polypropylene capacitors are used in the signal path. MIL type Switchcraft jacks and high performance switches ensure flawless operation. The power supply is optimised via measurement quality toroid transformer and a low impedance design to ensure the lowest possible noise. Through a double sided PCB all parts are roadworthy secured. A waterclear blue LED perfects the aesthetics of the DI box.
Technical Data Input impedance > 20 MOhm Output impedance180 Ohm at 1 kHz Frequncy response 20 Hz - 20 kHz (-0,1 dB) 5 Hz - 120 kHz (-3 dB) THD at 0 dBv 0,06% at 20 Hz 0,04% at 1 kHz 0,035% at 20 kHz Signal to Noise Ratio 86 dB Tube ECC 83/7025 A - military E 83 CC optional Output transformer JENSEN JT-DB-E Polarity Pin 2 Hot , AES/IEC -Standard Max. Input voltage > 30 V peak |
Reviews
There are no reviews yet.