Content |
DB1P is a single-channel passive DI BOX equipped with the same type of MU-METAL core transformer used in the DB1A, which provides minimum distortion, linear phase and hum-free transmission also on very long cables. Thanks to the input stage design, DB1P can accept also signals coming directly from the power output of instrument amplifiers, PAD up to 60 dB. A specially designed input filter is also available for cutting any hiss or buzz noise coming from acoustic or electric guitar and basses.
Technical Specifications
Type :
|
1 channel passive DI
|
Width :
|
215 mm(8.465inch )
|
Height :
|
50 mm(1.969inch )
|
Depth :
|
125 mm(4.921inch )
|
Weight :
|
1 kg(2.205lb )
|
Rack Units :
|
1/2 rack unit.
Removing the two molded sides and attaching two units, with the supplied brackets, you can mount two by two DI boxes into a standard 19¿ rack.
|
Inputs :
|
Two Parallel 1/4' jack connectors and one parallel RCA connector (unbalanced).
|
Input Impedance :
|
120 kOhm (pad at 0 dB)
47 kOhm (pad at -20/-60 dB)
44 kOhm (pad at -40 dB)
|
Input Levels :
|
+15 dBu (pad at 0 dB)
+35 dBu (pad at -20 dB)
+55 dBu (pad at -40 dB)
+75 dBu (pad at -60 dB)
|
Outputs :
|
XLR male: Pin 2 Hot / Pin 3 Cold / Pin1 Ground
|
Output Levels :
|
into 1 KOhm or greater
-5 dBu (for 0.1% THD at 50 Hz)
+5 dBu (for 0.1% THD at 1k Hz)
|
Channels :
|
1 nr.
|
Frequency response :
|
10 Hz to 100 kHz, +0 dB/-1 dB
|
Distortion (THD) :
|
|
S/N Ratio :
|
|
Controls :
|
Pad -20, Pad -40, Gnd Lift, Filter (12' emulator)
|
Notes :
|
Insertion loss 20 dB
CMR > 100 dB
Phase distortion 0° at 20 Hz, 0° at 20 kHz.
|
Rear View
|
Active DI-Box SM-60
The electronic Direct-Injection Box SM-60 allows direct connection of electronic music instruments such as keyboards, synthesizers, electric and electronic pianos, etc. with mixing consoles in PA-systems and in recording studios. The SM-6 is designed for applications, where a passive DI-Box does not perfom satisfactorily, i.e., where the output level of a passive DI-Box is too low for the microphone input section of the mixing desk. Because the input impedance of the SM-6 is above 5 MOhm, instrument outputs are not loaded or in any other way adversely affected. The voltage ratio from input to output is 1: 1 and is always sufficient for connection with any microphone input. Input connectors are 1/4" phone jacks, output connector is a Switchcraft D3M; output is 600 Ohms, transformer balanced. The output level may in certain cases overload microphone inputs - the line input section of the mixing console must then be used for connecting the SM-6. The unit operates with a 9 V battery or phantom powering from 24 to 48 volts.
Technical Data
input impedance > 5 MOhm max. input impedance + 6 dBu, 1,55V ouptut impedance 600 Ohm frequency response 20 ... 20000 Hz, ± 0,2 dB gain 1 : 1 THD < 1 % at 30 Hz < 0,7 % bei 40 Hz powering 9-V battery (IEC 6LF22) or phantom power 24 ... 48 V. inputs two 1/4" phone jacks , unbalanced (one being used as output to instruments amp) outputs XLR, balanced pin 1 = ground, pin 2 = hot, pin 3 = cold case aluminium die-cast weight 240 g dimensions 113 x 71 x 37 mm |
The Stewart ADB-1 is a single channel active direct box that allows an unbalanced source to directly feed a balanced input. Musical instruments, tape recorders, VCRs and sound projectors can be run "direct" to the mixing console, avoiding unnecessary degradation of sound quality. The ADB-1 operates on either phantom power or a 9-volt battery.
FEATURES: Flat response Low distortion Low noise Wide dynamic range No transformer RF protection on input and output Switchable ground isolation Flush mounted slide switches |
You're serious about getting rid of all that excess noise on stage, but you've got so many line instruments you don't know where to start. The ADB-4 from Stewart can take care of all your high impedance problems. The ADB-4 is 4 active direct boxes, all in a module that only takes up half a space on your keyboard rack. It's a rugged, durable piece of equipment that packs a lot of DI power.
? Requires phantom power or 9v battery ? Ground lift switch ? Instrument or speaker level switch ? Transformerless ? Can be used with amp up to 400w ? RF shielding |
Phantom or battery powered in a rugged steel chassis The ARX DI-PLUS 2 represents another major step forward in active direct boxes. Packaged in a single channel stand-alone format, the DI-PLUS 2 represents a fresh look at active stereo D.I. concepts.
Precision engineered Ultra quiet, ultra clean circuitry delivers maximum headroom whatever the signal. Premium grade components, plus an all-steel chassis gives excellent hum and noise specifications and superb audio quality in a tough, roadworthy package. Accurate Left and Right channel level matching keeps the stereo image centred.
Level control The DI-PLUS 2 features two high impedance unbalanced inputs on the front panel, running to balanced XLR outputs on the rear. A a global Pad switch drops inputs by 20dB, making it suitable for all applications from the softest keyboard to the hottest broadcast levels. Battery compartment The revolutionary simple 'clamshell' action of the DI-PLUS 2 battery compartment makes battery changing extremely easy, even on the darkest stages. A 9v alkaline battery snaps into a PCB mounted battery holder for fast, secure location. No fragile battery clip leads to break, no tools required, no screws to lose. Production crew heaven! Automatic Phantom switching The DI-PLUS 2 will automatically switch itself to the console's own Phantom Power, if available, and an LED will indicate this mode. Turn the Phantom Power off and it will instantly revert back to battery mode.
Rugged all-steel case A lot of direct boxes are fitted into brittle cast alloy cases. Not this one! The tough all-steel inner and outer chassis of the DI-PLUS 2 provide excellent RF/EMF shielding while making it a sturdy, heavy duty unit that is hard to dislodge, and hard to leave behind. Rear panel showing Left and Right XLR connectors, ground lift switch, battery check switch and LED, plus phantom power On LED and captive screw for opening up the unit for battery changing Whether you're a Studio or Live Sound engineer, installation contractor, or broadcast engineer, you want all the dynamics,clarity and stereo information of the original sound source transferred to the mixing console. The ARX DI-PLUS 2 provides a rugged, no-compromise solution to all stereo direct injection and signal balancing requirements. T E C H N I C A L S P E C I F I C A T I O N S: Max Input Level +12 dB Phantom powered +6 dB Battery powered Input Impedance 1 Meg Ohm Max Output Level +17 dB 10K Ohm load Phantom powered +12 dB 10K Ohm load Battery powered +11 dB 600 Ohm load Phantom powered +12 dB 600 Ohm load Battery powered Output Impedance 680 Ohms Balanced Output Signal to Noise -100 dB unweighted -104 dB A weighted Dynamic Range 117 dB 10K Ohm load Phantom powered 112 dB 10K Ohm load Battery powered 111 dB 600 Ohm load Phantom powered 107.5 dB 600 Ohm load Battery powered Distortion 100 Hz .0018%, 1KHz .0028%, 10KHz .0056% Frequency Response 20Hz to 20KHz, ± 0.2 dB Gain through Unit: 6dB (Pad switch out) Pad Switch: Global -20 dB attenuation Input and Loop Out Connectors Insulated jacks (!!!Note that Channel A Input connector switches the unit on when a plug is inserted. Remove plug when storing to avoid battery drain!!!) Output Connectors 3 pin XLR. Wired Pin 1 Ground, Pin 2 + Hot, Pin 3 - Cold. Global Audio Ground (Pin 1) lift switch Construction All-steel chassis, fibreglass PCB Battery Access Twist connector opens chassis, snap-in battery holder inside. No tools required
| 2-channel passive DI box for line and loudspeaker levels. PAN-04 consists of a housing containing the equivalent of two PAN-01s, making it a dual channel passive DI box. This „stereo" configuration makes it ideally suited for use with certain keyboards and devices which have several outputs.ive DI box. Jack input with paralell „THRU" output, transformer balanced XLR output. Attenuable input sensitivity, can handle both line level and speaker level signals.
Specifications
- No. of channels: 2
- Passive/Actibe: Passive
- Transformer balanced: Yes
- Attenuator: -30 dB
- Input/Output Gain: -20 dB
- Ground lift switch: Yes
- Max Input Level: +54 dBu
- Max Output Level: +4 dBu
- Frequency Range 2K Source Imp. -1dB: 10 Hz - 40 kHz
- Input Impedance 60Hz: 60 kΩ
- Nom. Output Impedance: 600 Ω
- Housing: Steel
- Dimension: 110 x 110 x 45 mm
|
Reviews
There are no reviews yet.