Content |
- High performance active direct box
- Increased dynamic range and headroom
- 48V phantom powered with switching supply
- Ideal for acoustic guitar and bass
The Radial Pro48 is a compact high-performance 48V phantom powered active direct box designed specifically for todays high output instruments.
The Pro48's innovative internal switching power supply significantly increases headroom producing less distortion while yielding a smooth, linear response that extends from 20Hz to well above 40kHz. This results in natural, uncolored signal that is as good or better than DI boxes costing several times more. The superior performance makes the Pro48 an ideal candidate for use with battery powered active basses and acoustic guitars that tend to overload other direct boxes.
The compact Pro48 is built road-ready with 14 gauge steel throughout. A unique book-end™ design creates a protective zones around the switches and connectors while the internal I-beam construction assures outside stress will not torque the PC board and deteriorate solder connections. A full bottom no-slip pads adds mechanical isolation and electrical insulation to further extend the Pro48's lifespan.
Exceptional sonic performance, great natural tone and an affordable price tag! The Radial Pro48 truly represents a breakthrough in value. | 2-channel passive DI box for line and loudspeaker levels. PAN-04 consists of a housing containing the equivalent of two PAN-01s, making it a dual channel passive DI box. This „stereo" configuration makes it ideally suited for use with certain keyboards and devices which have several outputs.ive DI box. Jack input with paralell „THRU" output, transformer balanced XLR output. Attenuable input sensitivity, can handle both line level and speaker level signals.
Specifications
- No. of channels: 2
- Passive/Actibe: Passive
- Transformer balanced: Yes
- Attenuator: -30 dB
- Input/Output Gain: -20 dB
- Ground lift switch: Yes
- Max Input Level: +54 dBu
- Max Output Level: +4 dBu
- Frequency Range 2K Source Imp. -1dB: 10 Hz - 40 kHz
- Input Impedance 60Hz: 60 kΩ
- Nom. Output Impedance: 600 Ω
- Housing: Steel
- Dimension: 110 x 110 x 45 mm
| With added functionality and enhanced audio performance, the AR-133 has been
designed to be more affordable for musicians, studios and PA companies.
The unit includes phantom power and battery supplies as standard. Should the
phantom power from the console fail or be accidentally switched off, the AR-133
automatically switches over to the internal 9V battery providing uninterrupted use.
The unit is housed in a rugged aluminium extrusion case, with robust polyurethane
end-cheeks which give the AR-133 a very distinctive look.
Input connectors are both 1/4" jack sockets and an XLR socket, the latter meaning
that the AR-133 can be used to convert unbalanced signals to a balanced output on
XLRs throughout.
The arched case allows cables to run back underneath the unit from the end for neat
cable management.
Input attenuation is 0, -20 or -40dB, making the box suitable for instrument, line or
amplifier levels on inputs. On the output side, a ground-lift switch is provided for quick
solutions to ground-loop problems.
The AR-133 uses an enhanced version of the same audio path as the AR-116, now
regarded by many people as a reference standard. The sound quality is legendary,
particularly on acoustic and bass guitars.
Numerous applications can be satisfied by the AR-133. For example, as well as the
traditional guitar use, the AR-133 can be used with keyboards, DJ consoles, amplifier
outputs, and other electronic sources.An additional bonus is the ability to use the AR-133
as an active balancing device.
Input Section
Input Impedance 1M Ohm (pad at 0dB)
47k Ohm (pad at -20dB)
47k Ohm (pad at -40dB)
Max Input Level +9dBu (pad at 0dB)
+29dBu (pad at -20dB)
+49dBu (pad at -40dB)
Connectors Two Parallel 1/4" jack connectors and a parallel
XLR connector (unbalanced)
Jack: Tip Hot (+ve)
Sleeve Ground
XLR: Pin 2 Hot (+ve)
Pin 1 & 3 Ground
Output Section
Output Transformer Balanced
Max. Output Level +8dBu into 600 Ohms or greater
Connector XLR3-32 or equivalent
System Performance
Distortion (THD) < 0.005% at 1khz, 0dbu output
Noise < -105db unweighted, 22hz-22khz, rms*
Frequency Response 30Hz to 20kHz, +0dB/-1dB
General
Main/Standby battery 9 volt PP3 type, preferably alkaline.
Current drain on phantom - less than 7.5mA
on battery - less than 2mA.
Phantom Power +20 volts DC to +48 volts DC
Weight 650 gms, excluding batteries.
Overall Dimensions 59 mm x 124 mm x 143 mm
(2.3" x 4.9" x 5.6“) |
1-channel DI box, passive Converts unbalanced 6.3 mm jack line input (e.g. from instruments) into balanced XLR output for connecting a mixer Switchable input attenuation: 0 dB, -20 dB, -40 dB Ground-lift switch eliminates ground loop problems 1 signal input (6.3 mm jack) 1 parallel output (6.3 mm jack), feed-through of the input signal 1 low-impedance output (XLR) Gray housing | Behringer DI-600P High-Performance Passive Direct Injection Box
Introducing the Ultra-Compact DI-Boxes from BEHRINGER
There are times when you will want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. A direct connection between audio equipment can be a challenge though: technical problems crop up that?ll corrupt the signal.
The DI600P lets you connect instruments or amplifier outputs of up to 3,000 Watts. It converts any unbalanced signal to a balanced signal and eliminates unwanted noise. With its high-performance transformer, it also allows you to use very long cables without the loss of high frequencies.
This is the sort of medicine that?ll cure headaches in your studio or on stage.
It often happens that you want to connect certain sound sources straight to other audio gear, be it for a live performance or a studio session. The direct connection between audio equipment can quickly turn out to be a real challenge: technical problems crop up that can affect the signal.
Hook Your Guitar or Amp Up to the PA
Be ready for your next gig with the Behringer Ultra-DI DI600P direct box. Designed to send instrument or amplifier signals to the main mixing board, the DI600P is a high-performance passive DI is a useful tool in any gig rig or studio. Dual 1/4" TS jacks are wired in parallel let you plug your instrument into one and use the other as an output to your amp. The balanced XLR mic-level output feeds your mixer a clean and super-flat signal that is true to the source. Sweetwater knows that grounding issues and hum can be a problem at live gigs. The DI600P sports a ground lift switch to kill unwanted ground loops and hum. It also has a filter switch for optimal guitar tone and an instrument/amp switch with a 30dB input level drop. The Behringer Ultra-DI DI600P direct box is an extremely useful tool for any stage rig!
Behringer Ultra-DI DI600P Direct Box Features:
- Compact, high-performance passive direct box
- Jack input 1/4" TS in and parallel out
- Gold-plated XLR output / impedance balanced
- Super-flat frequency output for uncolored sound
- Switchable filter that optimizes the DI for guitars
- Instrument/Amp switch lowers the input level 30dB for feeding amplifiers into the DI
- Instruments or amplifier outputs with up to 3,000 watts can be connected directly
- Offers impedance and signal matching of instruments to mixers
- Perfect for stage and studio use
- Ground lift switch eliminates typical ground loop problems
- Rugged metal case can take the rigors of the road
Get your signal to the board with Behringer\'s Ultra-DI DI600P direct box!
Tech Specs
- Type: Passive DI Box
- Channels: 1
- Ground Lift: Yes
- Inputs: 1 x 1/4"
- Outputs: 1 x 1/4“, 1 x XLR
- Height: 1.4"
- Width: 3.75"
- Depth: 5"
- Weight: 0.66 lbs.
- Manufacturer Part Number: DI600P
| |
Reviews
There are no reviews yet.