Content |
The challenge when using a condenser microphone with a preamp pedal, direct box or stage amp is that most of these only have unbalanced inputs. And as most phantom power supplies are only equipped with balanced inputs and outputs, making a proper connection is often difficult or impossible due to the impedance and level mismatch.
The SB-48UB is a single channel phantom power generator that converts the power from a 15VDC supply to 48 Volts for use with a condenser microphone or active direct box. Inside, the SB48-UB converts the signal to both a lo-Z balanced XLR output and a hi-Z unbalanced ¼" out. Both outputs may be used concurrently whereby the XLR could feed the PA while the ¼" out could feed a stage amp or pedalboard
| Adam Hall Connectors 4 STAR A JF3 MM3 Adapter 6.3 mm jack stereo female to 3.5 mm jack stereo male
Our adapter series consists of little helpers and some "must-have's", like the 4 STAR A JF3 MM3. With this adapter you can change a 6.3 mm jack plug to a 3.5 mm minijack. Some earphones use 6.3 mm jack plugs, but some computers only have minijack socket. Here is your solution.
Product type
Plugs and Connectors
Gender of connector 1
female
Gender of connector 2
male
| Alctron PS200 Portable 48V Phantom Power Supply for Condenser Microphone Live Broadcast Mic Power Supply
The PS200 is portable, battery-operated, and designed to provide 48V phantom power to any condenser microphone in remote locations
It also features a DC power loop enabling multiple unit operations
Power condenser microphones requiring phantom power
Operates on two 9 Volt alkaline batteries, or the included 9V DC adapter
High-frequency switching power supply to eliminate noise
Utilizes a switching regulator for stable voltage performance
Battery life approx. 10 hours, using one 9V alkaline battery
Package Included:
1 x Power Supply(microphone and battery are not included) |
The APT20 is a phantom power supply unit for use with two condenser microphones. It supplies 48 V DC to the microphones and routes the signal to a mixer or microphone amplifier. It features XLR connections for in- and output, and at the back is an euro power connection with power switch provided.
|
- 12 V / 48 V switchable
- 2 XLR inputs
- 2 XLR outputs
- Operating voltage: 12 V / 150 mA (via enclosed power supply unit) or 2x 9 V batteries
- Dimensions: 143 x 93 x 45 mm
- Weight: 485 g
|
The K6 powering module is the heart of this Sennheiser professional modular
microphone system and can be powered either by its internal 'AA' size 1.5 V
battery or by 12 - 48 V phantom power. The K6 can be combined with different
condenser microphone heads to provide a wide variety of polar patterns. Matt
black, anodised scratch-resistant finish.
Profile
Powering module for battery/phantom powering with switchable roll-off filter, battery
on/off switch with battery test. Suitable for ME 62 - ME 67 microphone heads and
-60 versions of MKE microphones.Transmission factor 0 dB at 1 kHz, nominal
impedance 200 Ohm, min. terminating impedance 1 kOhm, max. output voltage 2 V
(at 1 kHz), power supply: phantom powering 12 - 48 V or 1.5 V (AA size)alkaline
battery, supply current 2.2 mA, battery life approx. 150 h, dimensions in mm:
? 22 x 155, resultant length 94 mm, weight approx. 45 g.
Features
Switchable bass roll-off filter protects against rumble, handling, pop and wind noise
On/off switch with battery test
High output, low noise
Transformerless balanced output on 3-pin XLR connector
Delivery Includes
1 K6 powering module
1 MZQ 200 microphone clamp
1 AA battery
1 protective carrying case
Technical Data
Nominal impedance 200 Ohm
Min. terminating impedance 1000 Ohm
Output voltage 2 V
Power supply Phantom 12 - 48 V 1x Typ IEC LR 06
Current consumption 2,2 mA
Operating time (Battery) max. 150 h
Dimensions d 22 x 94 mm (netto)
Weight ca. 45 g
Gain 0 dB
|
Reviews
There are no reviews yet.