Content | KODA REACT PA-70 Amplifier with bluetooth, usb, tuner radio, 150W 100V
Priority input and radio 150W
USB or Card reader
2 AUX in, 1 AUX out
2 mic in (1 with priority)
With remote control
Output 8-16Ω/70V/100V, 1 zone |
Crown CDi 2000 2x800W-4Ω Power Amplifier
The Crown? CDi 2000 power amplifi er shall be a solid-state two-channel model
with a switch-mode universal power supply.
The outputs shall be usable as dual or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output
voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to
access menu items and front panel lockout.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal
processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level
signal is present at input.
?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below
clip.
?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB
below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is
ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible
distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature
conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on
and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a
balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers
or bridge-mono loudspeaker. Dual connectors shall work with 2-8 ohm or
70V loads. Bridge-mono connectors shall work with 4-8 ohm or 140V loads.
HiQnet USB Connector: Type B, connects to a USB port on a PC.
The amplifi er shall have the following specifi cations:
Output Power: 2 ohm Dual (per channel): 1,000W with 1% THD, 4 ohm Dual
(per channel): 800W, 8 ohm Dual (per channel) 475W, 4 ohm Bridge-Mono:
2,000W with 1% THD, 8 ohm Bridge-Mono: 1,600W, 70V Dual (per channel):
800W.
Voltage Gain at 1kHz, 8 ohm rated output: 32.9 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Dual
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity: 1.4V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 100 dB (A
weighted).
Damping Factor: Better than 500 from 20 Hz to 400 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.
Maximum Input Signal: +22 dBu typical.
AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V,
50/60 Hz.
AC Line Current: 6.9A.
At Idle: Draws no more than 90 watts.
Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).
The DSP section shall have the following specifi cations:
Input EQ: 6 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
Also adjustable high and low shelving fi lters. This 8-fi lter EQ section can be
bypassed.
Crossover Filters: Highpass and lowpass per channel. Butterworth 6/12/18/24
dB per octave and Linkwitz-Riley 24/48 dB per octave. Also includes ±15 dB
bandpass gain and polarity control.
Output EQ: 8 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
This 8-fi lter EQ section can NOT be bypassed. Filters are enabled individually.
Delay: Up to 50 msec total delay per channel.
Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6,
or ?12 dB threshold per channel.
Presets: 20 presets. 19 are user-defi nable.
Protection shall include the following:
CDi-Series amplifi ers shall be protected against shorted, open or mismatched
loads; overloaded power supplies; excessive temperature; chain destruction
phenomena; excessive output current, and input overload damage. They also
protect loudspeakers from input/output DC, large or dangerous DC offsets and
turn-on/turn-off transients
The chassis shall be steel. Cooling shall be by a proportional speed fan with
front-to-rear airfl ow.
Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5
in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface.
Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg).
The amplifier shall be designated the Crown CDi 2000.
|
- HIGH POWER, LOW DISTORTION
120W of RMS power with less than 1% THD.
- ADVANCED PROTECTION CIRCUITRY
Thermal and current overload protection, power-on delay and automatic idling circuitry for component and loudspeaker protection.
- BATTERY BACKUP
Can be powered by 24VDC battery for emergency backup and true portability.
- SLIM DESIGN, COMPACT SIZE
Streamlined design fits in a compact 3RU space.
PA- 2312
|
Rated Output (RMS, THD 1%, 1kHz)
|
120W
|
Input Sensitivity/Impedance
|
1V/10kΩ, Balanced
|
T.H.D
|
Less than 1%
|
S/N
|
Better than 95dB
|
High Pass Filter
|
-3dB at 400Hz
|
Channel Separation
|
Less than –70dB
|
Output Voltage/Impedance
|
EC, JAPAN: 4Ω/22V, 41Ω/70V, 83Ω/100V
|
USA/CANADA: 4Ω/22V, 5.2Ω/25V, 41Ω/70V
|
Power Source
|
100–120VAC or 220–240VAC; 50/60Hz, 24VDC
|
Power Consumption(1/8 Power)
|
290W
|
Weight
|
20Kg/44.1Ib
|
Dimensions
|
482(W) x 132(H) x 280(D)mm/19(W) x 5.2(H) x 11(H)in
|
|
Specifications Frequency Response (at 1 watt into 4 ohms, 20Hz - 20 kHz) |
+0/–1 dB
| Signal to Noise Ratio (below rated 8-ohm power at 1 kHz, A-weighted) |
100 dB
| Damping Factor (8 ohm): 20 Hz to 400 Hz |
> 500
| Input Stage |
Input is electronically balanced and employs
precision 1% resistors
| AC Line Current |
CDi 1000: 11.50A, CDi 2000: 11.93A, CDi 4000: 11.75A
At idle: Draws no more than 45 watts.
| Crosstalk (below rated power) 20 Hz to 1 kHz |
> 70 dB
| Input Impedance (nominal) |
20 kilohms balanced, 10 kilohms unbalanced
| Load impedance (note: safe with all types of loads)
Dual
Bridge mono |
2–8 ohms
4–16 ohms
| Voltage Gain (at 1 kHz, 8 ohm rated output) |
CDi 1000: 30.5 dB, CDi 2000: 32.9 dB, CDi 4000: 34.2 dB
| Sensitivity (at 8 ohm rated output) |
1.4V
| Maximum Input Signal |
+22 dBu typical
| Operating Temperature |
0° C to 40° C at 95% relative humidity (non-condensing)
| AC Line Voltage and Frequency Configurations Available (± 10%) |
100V, 120V-240V, 50/60 Hz
| Ventilation |
Flow-through ventilation from front to back
| Cooling |
Heat sinks and proportional-speed fan
| Dimensions: Width, Height, Depth (behind mounting surface) |
EIA Standard 19 in. W (EIA RS-310-B)
x 3.5 in. (8.9 cm) H x 12.25 in. (31.1cm) D
| Net Weight, Shipping Weight |
19 lb (8.6kg), 22 lb (10.0 kg)
| |
Crown CDi 1000 2x700W-4Ω Power Amplifier
The Crown? CDi 1000 power amplifi er shall be a solid-state two-channel model with a switch-mode universal power supply. The outputs shall be usable as dual or bridged-mono modes of operation. The bridged-mono mode shall bridge the outputs to provide increased output voltage. Front panel controls and indicators shall include the following: Level: Detented rotary level control, one per channel. Power Switch: On/off switch applies AC power to the amplifi er. Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to access menu items and front panel lockout. LCD Screen: Backlit liquid crystal display shows speaker presets and signal processing. Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input. ?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below clip. ?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB below clip. Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is ready to produce audio. Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion. Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions. Power Indicator: Blue LED illuminates when the amplifi er has been turned on and has power. Rear panel controls and connectors shall include the following: AC Line Connector: NEMA 5-15P (15A). Input Connector: Two 3-pin removable Phoenix-type connectors each accept a balanced line-level input signal. Output Connectors: 4-position barrier strip with connectors for dual louspeakers or bridge-mono loudspeaker. Dual connectors shall work with 2-8 ohm or 70V loads. Bridge-mono connectors shall work with 4-8 ohm or 140V loads. HiQnet USB Connector: Type B, connects to a USB port on a PC. The amplifi er shall have the following specifi cations: Output Power: 2 ohm Dual (per channel): 700W with 1% THD, 4 ohm Dual (per channel): 500W, 8 ohm Dual (per channel) 275W, 4 ohm Bridge-Mono: 1,400W with 1% THD, 8 ohm Bridge-Mono: 1,000W, 70V Dual (per channel): 500W. Voltage Gain at 1kHz, 8 ohm rated output: 30.5 dB. Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms. Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to 16 ohms in Bridge-Mono mode. Sensitivity: 1.4V. Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 100 dB (A weighted). Damping Factor: Better than 500 from 20 Hz to 400 Hz. Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz. Input Stage: Input is electronically balanced and employs precision 1% resistors. Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced. Maximum Input Signal: +22 dBu typical. AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V, 50/60 Hz. AC Line Current: 6.5A. At Idle: Draws no more than 90 watts. Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing). The DSP section shall have the following specifi cations: Input EQ: 6 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving fi lters. This 8-fi lter EQ section can be bypassed. Crossover Filters: Highpass and lowpass per channel. Butterworth 6/12/18/24 dB per octave and Linkwitz-Riley 24/48 dB per octave. Also includes ±15 dB bandpass gain and polarity control. Output EQ: 8 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut. This 8-fi lter EQ section can NOT be bypassed. Filters are enabled individually. Delay: Up to 50 msec total delay per channel. Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6, or ?12 dB threshold per channel. Presets: 20 presets. 19 are user-definable. Protection shall include the following: CDi-Series amplifi ers shall be protected against shorted, open or mismatched loads; overloaded power supplies; excessive temperature; chain destruction phenomena; excessive output current, and input overload damage. They also protect loudspeakers from input/output DC, large or dangerous DC offsets and turn-on/turn-off transients The chassis shall be steel. Cooling shall be by a proportional speed fan with front-to-rear airfl ow. Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5 in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface. Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg). The amplifier shall be designated the Crown CDi 1000. |
P-120D features 2x 200W into 4 Ohm load. This amplifier matches the needs for noiseless operation through air-cooling. It is ideally suitable in studios, small theatres, cabarets, churches, conference- and multimedia rooms etc. Multiple protection circuits care for stable operation. The amplifier is rackmountable (2 units). The optional transformer LT-101 converts the input to a balanced transformer isolated input. |
Reviews
There are no reviews yet.