| Content |
Amplifier PA with priority input
& radio 90WRMS (150W Peak)
USB or Card reader playback
3 AUX in, 1 AUX out
2 mic inputs (1 with priority)
With remore control
Outputs 8-16Ω/70V/100V 4 selectable outputs by switch |
XB Series - Intelligent Power
Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile, dynamic and
extremely rugged according to IEC286-3. For the highest requirements in safety
and quality.
Sequential power on, alive contacts and incorporated ground fault detection -
the XV is the solution under all conditions. Without the need for additional equipment.
For uninterrupted and troublefree operation.
Needless to say that the Bittner High-End toroidal output transformers in the XV
series are some of the best available.
High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX
High-End Toroidal Output 100V Transformers
Ground Fault Detection
LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty
TECHNICAL DATA:
XV 200: 2x 100 W / 100 V
Class: AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.07%
Signal-to-Noise Ratio: < 101 dB
Channel Seperation: > 70 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Cooling: 2 to 3 fans (temp. reg. variable speed)
Weight: 15 kg
Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)
|
| | - MODULAR DESIGN Optional modules can be installed in multiple configurations for convenience and ease of use. Choose the PAM-CDA (Compact Disc), PAM-T (AM/FM Tuner) or PAM-D (Cassette Deck) modules to expand the PAM-120A/340A/480Aʼs audio capabilities. - INDIVIDUAL INPUT GAIN CONTROLS Rear-panel gain controls for each input channel for total control of individual levels. - SPEAKER SELECT Six speaker select switches enable you to select any combination of up to five speakers. - SELECTABLE PRIORITY MUTING Switchable audio signal priority for Channels 1 and 2, Chime and Telephone input over other input sources. - REMOTE CONTROL INPUT (only PAM-340A/480A) Individual speaker zones can be selected and chime can be operated by wired remote control. - ANNOUNCEMENT CHIME Convenient four-tone chime for use with announcements. - EM(EMERGENCY) - OPTIONAL EMERGENCY VOICE IC (only PAM-340A/480A) When EM switch is pressed in emergencies, EM broadcasting stored in VOICE IC is outputted. | | | | | | | | | Rated Output Power | PAM-120A(THD 1%) : 120W (RMS) PAM-340A(THD 3%) : 340W (RMS) PAM-480A(THD 3%) : 480W (RMS) | | Frequency Response | | Amp In | 80Hz~20kHz | | Link In | 80Hz~15kHz | | CH1~CH6 | 120Hz~8kHz | | Remote In | 120Hz~8kHz(PAM-340A, PAM-480A) | | T.H.D.(at 1kHz Rated Output) | Less than 1%(PAM-120A) | | T.H.D.(at 1kHz Half Power Output) | Less than 0.5%(PAM-340A, PAM-480A) | | S/N | | Amp In | Better than 90dB(PAM-120A) Better than 88dB(PAM-340A/480A) | | Link In | Better than 65dB | | CH1~CH6 | Better than 50dB | | Remote In | Better than 50dB(PAM-340A/480A) | | Input Sensitivity/Impedance | | CH1~CH6 | | TRIM VR -60dB Position | 1mV/10kΩ | | TRIM VR -16dB Position | 158mV/10kΩ | | Link In | 100mV/10kΩ | | Amp In | 1V/47kΩ(PAM-120A) 1V/20kΩ(PAM-340A/480A) | | Remote In | 1V/10KΩ(PAM-340A/480A) | | Speaker Output/Impedance | PAM-120A : 120W/4Ω, 70V/42Ω, 100V/83Ω PAM-340A : 340W, 100V/29.4Ω PAM-480A : 480W, 100V/20.8Ω | | Preamp Output/Impedance | 1V/600Ω | | Tone Control (100Hz, 10kHz) | ±12dB | | CH1~CH6 EQ Control (100Hz, 1kHz, 10kHz) | ±12dB | | | | | | | | Power Source | 100–120VAC or 220V–240VAC; 50/60Hz, 24V DC(only PAM-120A) | | | (Supplied AC mains transformer depends on country requirements) | | Power Consumption | PAM-120A : 135W(1/8 POWER), 200W(1/3 POWER), 300W(FULL POWER) PAM-340A : 260W(1/8 POWER), 400W(1/3 POWER), 620W(FULL POWER) PAM-480A : 360W(1/8 POWER), 550W(1/3 POWER), 880W(FULL POWER) | | Weight | PAM-120A : 13kg/28.7lb PAM-340A : 13.5kg/29.7lb PAM-480A : 15.5kg/34.2lb | | Dimensions | 420(W) x 132(H) x 360(D)mm/16.5(W) x 5.2(H) x 14.2(D)in | | Operation Temperature | 14F~104F (-10°C~+40°C) | | ※ Specifications and design subject to change without notice. | | | |
|
XV Series - Intelligent Power
Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile,
dynamic and extremely rugged according to IEC286-3. For the
highest requirements in safety and quality.
Sequential power on, alive contacts and incorporated ground fault
detection - the XV is the solution under all conditions. Without the
need for additional equipment. For uninterrupted and troublefree operation.
Needless to say that the Bittner High-End toroidal output transformers
in the XV series are some of the best available.
High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX
High-End Toroidal Output 100V Transformers
Ground Fault Detection
LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty
TECHNICAL DATA:
XV 1600: 2x 800 W / 100 V
Class: AB
Frequency Response:20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.07%
Signal-to-Noise Ratio: < 101 dB
Channel Seperation: > 70 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Cooling: 2 to 3 fans(temp. reg. variable speed)
Weight: 39 kg
Dimensions: 3 RU / 483 x 88 x 382 mm(19" x 3.5" x 15 |
| | - SPEAKER SELECT(5ZONE SPEAKER OUTPUT) Six speaker select switches enable you to select any combination of up to five speakers. - SELECTABLE PRIORITY MUTING Switchable audio signal priority for MIC Channels 1, siren, Chime and Telephone input over other input sources. - MONITOR SPEAKER You can monitor output signal by using the monitor speaker, and can control the monitor level on front panel by 3 step lever switch. - ANNOUNCEMENT CHIME Convenient four-tone chime for use with announcements. - REMOTE CONTROL INPUT Individual speaker zones can be selected and chime can be operated by wired remote control. - EM(EMERGENCY) When EM switch is pressed in emergencies, EM broadcasting stored in VOICE IC is outputted. - REMOTE POWER You can turn on/off amplifier by remote control. - INDIVIDUAL INPUT GAIN CONTROLS Rear-panel gain controls for each input channel for total control of individual levels. - MODULAR DESIGN Optional modules can be installed in multiple configurations for convenience and ease of use. Choose the PAM-CDA (Compact Disc), PAM-T (AM/FM Tuner) or PAM-D (Cassette Deck) modules to expand the PAM-510/520ʼs audio capabilities. ACCESSORIES One detachable AC power cord is provided for use with this product. | | | | | | | PAM-510 | PAM-520 | | Amplifier Section (Amp In@1kHz, 4Ω Load Output) | Rated Output Power (THD 1%) | 120W(RMS) | 240W(RMS) | | Speaker Zone 1~5 Output | 25W MAX | 50W MAX | | Input Sensitivity/Impedance | 1V/20kΩ | | S/N | Better than 85dB | | Frequency Response (at 1kHz Half Power Output, ±3dB) | 80Hz~18kHz | | Mic Input Section (Mic 1~4 In@1kHz, Preamp Out) | Input Sensitivity/Impedance | –60dBV/600Ω | | S/N | Better than 55dB | | Frequency Response (±3dB) | 120Hz~10kHz | | Tone Control (Bass:100Hz,Treble:10kHz) | ±12dB | | Phantom Power | +24VDC | | Line Input Section (Line 1~2 In@1kHz, Preamp Out) | Input Sensitivity/Impedance | –30dBV/10kΩ | | S/N | Better than 65dB | | Frequency Response (±3dB) | 80Hz~15kHz | | Tone Control (Bass:100Hz,Treble:10kHz) | ±12dB | | Remote Amp Section (Remote In@1kHz, Preamp Out) | Mic Input Sensitivity/Impedance | –60dBV/600Ω | | S/N | Better than 55dB | | Frequency Response (±3dB) | 120Hz~10kHz | | Tel In Section (Tel In@1kHz, Preamp Out) | Input Sensitivity/Impedance | 0.3V/600Ω(USA/Canada) | | 0.775V/600Ω(EC & Associated) | | S/N | Better than 65dB | | Frequency Response (±3dB) | 330Hz~3kHz | | Pre Amp Out(Mic 1~4, Line 1~2, Tel In, Remote In) | 0dBV/600Ω | | | T.H.D | Less than 0.5% | | Record Out | –10dBV/3kΩ | | Operating Temperature | –10°C~40°C | | Power Source | 100–120VAC or 220–240VAC; 50/60Hz, 24VDC | | Power Consumption (1/8 POWER) | 180W | 320W | | Weight | 17kg/37.6lb | 19kg/42lb | | Dimensions | 482(W) x 132(H) x 398(D)mm 19(W) x 5.2(H) x 15.7(D)in | | ※ Specifications and design subject to change without notice. | | | |
|
The VP-200VX Power Amplifier Input Module is designed to be used in conjunction with theVP-2064, VP-2122, VP-2241 or VP-2421 power amplifier. |
Reviews
There are no reviews yet.