| Content |
The Fono MC is an exceptionally high quality MC phono stage designed to maximise the potential of any MC cartridge. Although specifically to compliment the latest Rega range of moving coils you will find full adjustability for loading is available via dip switches conveniently placed on the rear panel with two different gain settings located on the back panel making the Fono MC compatible with most low output MC cartridges.
The Fono MC has been designed to be effective, easy to use, and above all, to reproduce music. The Fono MC uses the Linear Systems low noise LSK389 FET in an all discrete input stage where low noise and linearity are vitally important to get the best from an MC cartridge. Because of the high input impedance of FET, the loading effects of the amplifier circuit are minuscule and do not affect the performance of the cartridge.
A MUSE operational amplifier is used in the RIAA equalization amplifier. Polypropylene capacitors have been used in the signal path and in the RIAA equalization circuits. There is selectable input loading for both resistance and capacitance along with two different gain settings located on the back panel making the Fono MC compatible with most low output MC cartridges.
The aesthetic design of the Fono MC was as important as the quality of its electrical capabilities, so it benefits from the same aluminium case as the Rega TTPSU and Fono MM amplifier, giving it a design which offers a familiar feel and moreover brings it in line with its illustrious bigger brothers. The new Fono MC circuit resulted from the design work carried out on the Aria phono amplifier.
The Fono disk stage is designed to amplify the signal from a moving coil cartridge to a level which can feed into a 200mV line level input on a standard hi-fi amplifier.
Specifications
Output impedance = 200Ω
Recommended minimum output load resistance = 5K
Frequency response (50KΩ output load) = 13Hz (-3dB) to 100KHz (-0.3dB)
RIAA accuracy (50KΩ output load) = Better than +/-0.2dB 100Hz to 100KHz
Power requirements = 24V AC at 150mA maximum. Only to be used with Rega PS1.
Input sensitivity (for 200mV output)
4 off = 133uV
4 on = 67uV
Input loading resistance
1 and 2 off = 400Ω
1 on = 100Ω
2 on = 150Ω
1 and 2 on = 70Ω
Input loading capacitance
3 off = 1000pF
3 on = 4300pF
Gain (at 1KHz)
4 off = 63.5dB
4 on = 69.5dB
Maximum input level (at 1KHz)
4 off = 6.7mV
4 on = 3.4mV
Load settings for adjustable MC stages
Impedance -100ohm
Capacitance - 1000pF
Gain setting - High (\'On\' position for Rega phono stages)
Fono MC dip switches settings (factory set at Rega for Rega MC models). |
Both Microsoft® Windows® and Apple® Mac OS® come with very simple audio recording software pre-installed. However, to take full advantage of the high-resolution recording facilities offered by the MM 008 ADC, we recommend recording software that can record at 24 bits/96 kHz and save lossless high-resolution audio files such as FLAC or Apple® Lossless.
Specs:
- Mode: MM/MC (switchable)
- Gain at 1 kHz: 40 dB (MM)/60 dB (MC)
- Input impedance (MM): 47 kΩ + 220 pF fixed
- Input impedance (MC): 47 kΩ + 1 nF (modifiable with external load plugs)
- Frequency response (flat): 20 Hz - 20 kHz ±0.3 dB
- Frequency response (-3 dB): 10 Hz - 50 kHz
- RIAA curve accuracy: ±0.3 dB
- THD+N: 72 dB (MC)
- Crosstalk: ≧40 dB
- Input sensitivity (MM): 3.29 mVrms for -10 dBV output (316 mVrms)
- Input sensitivity (MC): 0.325 mVrms for -10 dBV output (316 mVrms)
- Max. output voltage: 482 mVrms at 5 mVrms input (1 kHz)
- Output impedance: 47 Ω
- Input connections: 3 pairs of RCA sockets (left/right)
- Output connections: 1 pair of RCA sockets (left/right)
- Power supply: 24 V DC
- Power consumption: 3.4 W/15 mA
- Weight: 504 g (not including power supply)
- Dimensions: (W x H x D): 150 x 50 x 117 mm
|
Developed by our engineers, the new Ear benefits from a completely new surface mount PCB layout based on the hugely successful Brio-R amplifier. Exceptional performance is guaranteed with the convenience of independent mute, volume control and multiple connectivity options to integrate perfectly into any users system.
Power Supplies & Noise Reduction
The Ear pushes the Brio-R power amplifier circuit concept to a new level with the use of a low noise, fully regulated, supply. Noise has also been kept to a minimum by the use of an external mains transformer. The Ear exceeds the voltage requirements of IEC 268-15. This along with low output impedance makes it suitable for studio use as well as a hi-fi headphone amplifier. The Ear operates in Class A at normal listening levels.
High Quality Components
The Ear utilises the highest quality components and our engineers’ experience, to achieve the best sonic performance. Utilising the design ideals of the ‘cascaded emitter follower output stage’ with a pair of complementary Darlington output transistors, along with polyester film and Nichicon FG capacitors in critical positions, ensures it is our most advanced performing headphone amplifier to date.
Custom Case
Housed in a compact custom case, the Ear is designed to match the current range of Rega electronics with a matching, high gloss, front facia.The new Ear Headphone amplifier benefits from an all new extruded aluminium case and new styling giving it more of a family feel to match its illustrious big brothers. The Ear simply connects to the tape output of an amplifier via phono leads. The headphones are plugged into the front panel and there is a link socket in case you need your tape output sockets for other use.
Hi Fi News reviews the Rega Ear headphone amplifier:
\'The Rega Ear is lovely, in so many ways. It is beautifully made, stylish and has all the facilities you really need, plus a delightful sound that stirs the soul regardless of whatever music you put through it. Wonderfully expansive and big hearted, it makes listening a pleasure. Tonally it\'s slightly on the warm side, so suits poor quality sources down to the ground - even an iPad sounds good via the Rega!\' - January 2014.
- Maximum output level - 25 load 775mW, 32 load 685mW, 50 load 530mW, 100 load 320mW, 600 load 60mW
- Open circuit voltage 6v
- Input impedance 20K, Gain 28dB
- Frequency response 12Hz to 37kHz
- THD typically 0.003%
- Signal to noise ratio referenced to max output level -100dB (22Hz – 22kHz)
- Maximum Power requirements - 24VAC at 225mA (685mW 32)
- Dimensions: W 178mm x D 155mm x H 45mm.
|
THORENS MM-FLEX
The Thorens MM-Flex phono preamp is a high-quality preamplifier with portability in mind. Attach it to any surface with the included velcro adhesive—and better yet, due to its size you can take it with you! The Thorens MM-Flex is ideal for the on the go audiofile who may find themselves in a warehouse, surrounded by a particularly large sound system...for whatever reason.
MM-FLEX FEATURES
- Compact MM phono preamplifier
- Attaches to rear of turntable with integrated Velcro strip
- Can be easily removed and re-fitted without irreversible modification
|
The new Fono MM phono stage has been designed to be effective, easy to use, and above all, to reproduce music. The Fono MM uses a fully discrete, cascaded, complementary amplifier input stage, a configuration designed to optimise the performance of your moving magnet cartridge. Now housed in a brand new redesigned case to match the new Fono MC and Rega\'s latest range of electronic components offering a modern and sleek look guranteed to integrate in to any hi-fi system.
The new MK3 Fono MM replaces the multi award winning MK2 model which won
WHAT HI-FI? Best Phono stage in its price category 2014,2015 & 2016.
The RIAA equalization has been split into two stages to minimise interaction. Polyester capacitors have been used in the signal path and polypropylene capacitors are used in the RIAA equalization circuits.
The aesthetic design of the Fono MM was as important as the quality of its electrical capabilities, so it benefits from the same aluminium case as the Rega TTPSU and Fono MC amplifier, giving it a design which offers a familiar feel and moreover brings it in line with its illustrious bigger brothers.
Specifications
Input sensitivity = 1.7mV for 200mV output
Input loading = 47KΩ in parallel with 100pF
Maximum input level = 60mV at 1KHz
Gain = 41.4dB at 1KHz
Output impedance = 200Ω
Recommended minimum output load resistance = 5KΩ
Frequency response (50KΩ output load) = 15Hz (-3dB) to 100KHz (-0.2dB)
RIAA accuracy (50KΩ output load) = better than +/-0.2dB 100Hz to 100KHz
Power requirements = 24V AC at 80mA maximum.
Only to be used with Rega PS1.
| User's manual
- Ultra compact phono preamplifier and equalizer
- Proper RIAA equalization
- RCA inputs and outputs
- 6.3 mm stereo headphone output connector
- Sturdy metal housing
- 12 V AC/DC adapter included
The LD Systems PPA 2 is a very compact analogue phono preamplifier, which equalises the extremely low output signal of conventional turntables to RIAA standards. It allows you to connect to devices without any phono input, such as mixers, PA power amplifiers or sound cards. The phono inputs are designed as RCA jacks, just like the line outputs; the PPA 2 also has a screw terminal for the ground conductor of the turntable and a 6.3 mm stereo jack for connecting a headset. The THD factor of the preamplifier is below 0.05% and the channel separation is -75 dB. The LD Systems PPA 2 uses a 12 V AC adapter; a bright LED indicates the power supply on the top of the sturdy metal chassis.
Product type
Other Studio and Recording Equipment
Type
Stereo Input / Stereo Output
Frequency response
RIAA Curve Hz
Signal-to-noise ratio
70 dB
THD |
Reviews
There are no reviews yet.