Content |
Dominance reloaded: The 02 series of Reloop's Dominance amps combines intelligent electronics and qualitative manufacturing adding up to an amplifier solution for gastronomy, business and clubbing. The Dominance amplifiers' variable aerators keep the temperature at an optimum level at all times, a vast protective circuit package avoids unwanted overloading of any kind. With the three different capacity levels for 360, 720 and 960 watt every sound engineer should be able to find the right package.
Features:
- Heavy duty aerator with variable speed, keeps the amplifier at an optimum temperature in every condition
- Novel transistors
- Large, oversized cooling fins
- Overload protection and short-circuit protection
- High reliability
- Thermal protective circuit
- Separate amplifier circuits for channel A and B
- Ground/lift switch against background noises
- Aluminium cooling tunnel
- Outputs: PA speaker cord pro, screw clamps, 6.3 mm jacks
- Inputs: jacks, RCA
Technical features:
- 360 watt pro final amplifier
- Output rating:
2 x 180 w, 4 ohm
2 x 120 w, 8 ohm - Frequency range: 10 Hz - 50 kHz
- Dimensions: 482 x 88 x 314 mm
- Weight: 9.5 kg
|
The high efficiency of the ED series enables maximum efficiency with low heat generation.
A new and unique Class-H circuity technology using state of the art SMD Surface Mount Technology with a reduced number of components offering performance levels exceeding audiophile levels like a slew rate of 50V/µs and high-end extended dynamic sound. The amplifier provides 2x300W into 4 Ohm is equipped complete with temperature-controlled fan cooling, all common protective circuits such as over-temperature, short circuit, RFI and soft start.
The integral soft clip limiter protects against damage to the connected loudspeakers, the activity of a protective circuit, signal and limiter are shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS |
---|
Power output stereo 4Ω: | 2 x 300 Watt rms | | Power output stereo 8Ω: | 2 x 180 Watt rms | | Power output bridged 8Ω: | 600 Watt rms | | Frequency Response: | 20 Hz ÷ 20 kHz | | Signal/noise rate: | > 105 dB | | Crosstalk: | > 70 dB | | Distortion (THD+N): | | | Intermodulation: | | | Damping factor: | 200:1 (8 Ω) | | Slew rate: | 50 V/μS | |
INPUT SECTION |
---|
Input connector: | 2 x XLR balanced, 6,3mm jack unbalanced | | Input sensitivity: | 0 / 0.775 dBm/V RMS | | Input impedance: | 10.000 kΩ | | Controls: | Volume control for each channel | |
OUTPUT SECTION |
---|
Output connector: | 2 x Neutrik Speakon 4 ways | |
SYSTEM PARAMETERS |
---|
Cooling: | Two-speed fan | | Protections: | Temperature, DC, RFI short circuit, Soft-Start thermal on transformer | | Amplifier class: | H | |
POWER REQUIREMENT |
---|
Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 V ~ Hz | | Max.current: | 6 A | | Power Consumption: | 1300 W | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 88 / 3.46 mm/inch | | Width: | 483 / 19.01 mm/inch | | Depth: | 350 / 13.77 mm/inch | | Net Weight: | 11.45 / 25.24 Kg/Lbs | |
SHIPPING INFORMATION |
---|
Package height: | 120 / 4.72 mm/inch | | Package width: | 540 / 21.25 mm/inch | | Package depth: | 470 / 18.05 mm/inch | | Shipping Weight: | 13.81 / 30.44 Kg/Lbs |
| Phonic's MAX 1500 Power Amplifier provides 900 Watts of power at 8 ohms (bridge mono) or 450 Watts at 4 ohms (stereo) - ideal for clubs, churches, auditoriums and more. Input to the MAX 1500 amp is achieved via XLR or phone jack, and output is achieved either through Speakon-type connectors or traditional binding posts. The MAX 1500 features ground switches, user defeatable clip limiters, selectable high pass filters, and the option to choose between stereo, parallel and bridge operating modes, making this amplifier ideal for real world application.
- Output power: 450W @ 4 Ohms stereo, 280W @ 8 Ohms stereo
- High-current toroidal transformers for greater power and low noise
- Independent user-defeatable peak limiters reduce distortion
- Selectable High-Pass filter at 30Hz or 50Hz
- XLR and 1/4' TRS input jacks
- Binding post and Speakon?-type outputs
- Front mounted gain controls for easy access
- Signal and Peak LED indicators to monitor performance
- Short circuit, thermal, subsonic, RF protection, output DC offset
- Power on/off muting
|
The model L 500 is a 2 x 250 Watts Power Amplifier. Linear Precision Series power amps combine excellent audio performance, modern and innovative circuit design, meticulous and exceptionally rigid construction, and the highest levels of operational integrity and reliability with an appropriate and more than realistic price. The robust steel chassis provides outstanding torsional strength through L-shaped side panels reaching under the thick aluminium front panel. Thermal breakers prevent the power supply units from being damaged by thermal overload. Electronically controlled fans provide sufficient front-to-rear airflow and a special cool air diverter takes care of thermal stability. The fans? noise-level is extremely low which provides the possibility for studio use. If necessary, a supplied air-filter can be mounted behind the front panel ventilation louvres. Features * Excellent audio performance * Symmetrical topology * Ultra-low distortion * Generously dimensioned power supply units * Suitable to be operated on loads down to 2 ohms * Suitable to drive complex loads with phase angles of ± 90 degree * Extensive protection circuitry * Unique Back-EMF protection * Switchable limiters * Switchable Hi/Lo-Cut filters * Robust steel chassis * Exceptional low noise front-to-rear air-flow * XLR-type inputs and direct-outs * LED display shows On, In, Out, Limit and Protect * Highly reliable operation
Specs * Max. Output Power - into 8 ohms : 2 x 180 W at 1 kHz / THD = 1.0% * Max. Output Power - into 4 ohms : 2 x 280 W at 1 kHz / THD = 1.0% * Max. Output Power - into 2 ohms : 2 x 320 W at 1 kHz / THD = 1.0% * Max. Output Power - into 8 ohms bridged : 1 x 560 W at 1 kHz / THD = 1.0% * Max. Output Power - into 4 ohms bridged : 1 x 640 W at 1 kHz / THD = 1.0% * Rated Output Power - into 8 ohms : 2 x 175 W at 20 Hz - 20 kHz / THD = 0.1 % * Rated Output Power - into 4 ohms : 2 x 250 W at 20 Hz - 20 kHz / THD = 0.1 % * Rated Output Power - into 2 ohms : 2 x 300 W at 20 Hz - 20 kHz / THD = 0.1 % * Rated Output Power - into 8 ohms bridged : 1 x 500 W at 20 Hz - 20 kHz / THD = 0.1 % * Rated Output Power - into 4 ohms bridged : 1 x 600 W at 20 Hz - 20 kHz / THD = 0.1 % * Frequency Response : 0 dB ..... -1 dB/20 Hz - 20 kHz * Phase Angle Response : ± 30 degree/20 Hz.....20 kHz * Maximum Output Level : 45 V / RMS before clipping, no load, ref. 1 kHz / THD = 1% * Voltage Gain ref. 1 kHz : 26 dB (constant gain option) * Input Sensitivity : 0 dBu/0.775 V, +6 dBu/1.55 V at rated output / 4 ohms ref. 1 kHz * Maximum Input Level : +21 dBu / 8.7 V * Input Impedance active balanced : 20 kohms * THD at Rated Output : < 0.05 % MBW = 80.0 kHz, f = 1 kHz * IMD -SMPTE : < 0.01 % 60 Hz, 7 kHz, at rated output * Signal-to-Noise Ratio : >105 dB at rated output into 4 ohms, A-weighted, RMS, input sensitivity +6 dBu * Attenuation at rated output : > 70 dB f = 1 kHz * Damping Factor internal 1 kHz : > 300 * DIM 30 : < 0.01 % * DIM 100 : < 0.01 % * Slew Rate internal : > 25 V / ?s * Power Consumption : 300 W 1/8 rated output into 4 ohms * Width : 483 mm * Height : 88.1 mm * Depth : 426 mm * Weight : 14 kg |
BASIC Series - Intelligent Power
BASIC - that's meeting the tightest budgets and professional requirements in reliability, flexibility and sound. Alone or in combination with the other products of the Bittner portfolio. The consequent realisation of the Bittner quality standards indicates once more our understanding of the contracting business. It underlines our philosophy that cost consciousness has nothing to do with giving up standards. Compromise is a word unknown to Bittner Audio! The incorporation of detent potentiometers, clip limiter, protection circuits for any imaginable situation, as well as a first-class production process using only highest-quality components made the BASIC series the choice of most contractors.
Certainly more than basic!
High Tech SMT design Excellent sound and superior impulse response Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay XLR Inputs Speakon and Binding Posts Clip Limiter Toroidal transformers LED Indicators for SIGNAL, CLIP, PROTECT, POWER Temperature controlled, variable speed, low noise fans Detent potentiometers Stereo / Bridged / Parallel Mode Ground Lift Robust Steel Chassis 3 Year Warranty
TECHNICAL DATA: Basic 400: 2x 200 W @ 4 Ohm Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.03% Signal-to-Noise Ratio: < -102 dB Channel Seperation: > 85 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Damping Factor: > 400 @ 4 Ohm Cooling: 2x Fan (temp. reg. variable speed) Weight: 12 kg. Dimensions : 2 RU/483x89x265 mm (19" x 3.5" x 12.6“) |
These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.
Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 650 W, 4 Ω - 450 W, 8 Ω - 270 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 1150 W, 4 Ω - 660 W, 8 Ω - 350 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 1300 W, 8 Ω - 900 W Input Sensitivity, rated power @ 8 Ω, 1 kHz + 2,2 dBu (1,0 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class AB Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 12.6 kg (27.8 lbs)
|
Reviews
There are no reviews yet.