| Content |
Dominance reloaded: The 02 series of Reloop's Dominance amps combines intelligent electronics and qualitative manufacturing adding up to an amplifier solution for gastronomy, business and clubbing. The Dominance amplifiers' variable aerators keep the temperature at an optimum level at all times, a vast protective circuit package avoids unwanted overloading of any kind. With the three different capacity levels for 360, 720 and 960 watt every sound engineer should be able to find the right package.
Features:
- Heavy duty aerator with variable speed, keeps the amplifier at an optimum temperature in every condition
- Novel transistors
- Large, oversized cooling fins
- Overload protection and short-circuit protection
- High reliability
- Thermal protective circuit
- Separate amplifier circuits for channel A and B
- Ground/lift switch against background noises
- Aluminium cooling tunnel
- Outputs: PA speaker cord pro, screw clamps, 6.3 mm jacks
- Inputs: jacks, RCA
Technical features:
- 360 watt pro final amplifier
- Output rating:
2 x 180 w, 4 ohm
2 x 120 w, 8 ohm - Frequency range: 10 Hz - 50 kHz
- Dimensions: 482 x 88 x 314 mm
- Weight: 9.5 kg
|
VLP Series Powere Amplifier
Output Power: 300W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD 200W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD (Bridge Mode, Mono) 600W RMS @ 8 Ohms, 1K Hz, 1% THD
Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)
Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
Slew Rate: 15V Per usec
Damping Factor @ 8 Ohm: 300
Impedance: 20 Ohms balanced / 10 Ohms unbalanced
Cooling System: 2 indivdual fans
Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift Limiter
Dimensions (LxWxH): 14" x 19" x 3.5" / 360 x 482 x 88mm 2-rack mount spaces
Weight: 33 lbs. / 15 Kgs.
Special Features: High/Low Pass Filter; Input Sensitivity Selector; Ground Lift; Limiter
|
Reference Quality Power Amplifier [R-300 Plus] - Controls :
Front : Power on/off switch, attenuator, LED indicator
Rear : Mode seletor switch, Stereo/bridged mono switch - Connectors :
Input : 1 XLR, 1/4" balanced per channel
Output : 5-way binding post and SpeakonTM per channel - Indicators :
Power : Green, Protection : Red, Clip : Red, Signal : Green - Power Source : 100-120VAC or 220-240VAC; 50/60Hz
(supplied AC mains transformer depends on country requirements) - Power Consumption : 250W(2.4A)
- Weight : 8.4kg/18.5lb
- Dimensions (WxHxD) : 482x88x317mm/19x3.5x12.5in
|
Engineered from the ground up for unmatched quality and performance,
the Crown? DSi Series of power amplifiers offers three models of 500W,
800W, and 1200W per channel at 4 ohms. Onboard digital signal processing
includes crossovers, EQ filters, delay and output limiting. Rear panel HD-15
connector provides easy input/output connectivity between DSi amplifiers
and the new DSi-8M System Monitor.
The intuitive front panel LCD screen guides installers through a setup process?
featuring presets for the industry-standard JBL cinema loudspeaker systems?
to make configuration quick and easy.
At the touch of a button, Crown?s DSi cinema amplifiers deliver perfectly matched
performance with each award-winning JBL ScreenArray? system, making this the
ultimate cinema solution.
Features :
Includes three models of 500W, 800W, and 1200W per channel at 4 ohms
Automatic presets for popular JBL cinema speaker systems for quick, easy
configuration
Intuitive front-panel LCD screen guides installers through setup
Onboard digital signal processing includes crossovers, EQ filters, delay, and
output limiting
Computer connectivity via USB allows fast setup and configuration with HiQnet?
System Architect? software
Rear-panel HD-15 connector provides easy input/output connectivity between DSi
amplifiers and new DSi-8M System Monitor
Switch-mode universal power supply
All products fill 2U rack spaces and weigh under 19 pounds
Barrier strip outputs, removable Phoenix-style input
Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment
and guarantees its specifications
The Crown? DSi 1000 power amplifi er shall be a solid-state two-channel model
with a switch-mode universal power supply. A rear-panel HD-15 connector shall
provide input/output connectivity between the DSi amplifi er and the DSi-8M
System Monitor.
The outputs shall be usable as stereo or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output
voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to
access menu items.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal
processing.
Signal Indicator: Green LED, one per channel, fl ashes when a very low-level
signal is present at input.
?10 Indicator: Green LED flashes when output signal exceeds ?10 dB below
clip.
?20 Indicator: Green LED flashes when output signal level exceeds ?20 dB
below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is
ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible
distortion.
Temp/Fault Indicator: Red LED, one per channel, illuminates under Fault or
excessive temperature conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on
and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a
balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers
or bridge-mono loudspeaker.
HiQnet USB Connector: Type B, connects to a HiQnet network.
HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor.
The amplifi er shall have the following specifi cations:
Output Power: 2 ohm Stereo (per channel): 700W with 1% THD, 4 ohm Stereo
(per channel): 500W with 0.5% THD, 8 ohm Stereo (per channel) 275W with
0.5% THD, 4 ohm Bridge-Mono: 1,400W with 1% THD, 8 ohm Bridge-Mono:
1,000W with 0.5% THD.
Voltage Gain at 1kHz, 8 ohm rated output: 26 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity at 8 ohm rated output: 2.35V.
Sensitivity at 4 ohm rated output: 2.24V.
Sensitivity at 2 ohm rated output: 1.88V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB
(A weighted).
Damping Factor: Better than 500 from 20 Hz to 500 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.
Maximum Input Signal: +22 dBu typical.
AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V,
50/60 Hz.
AC Line Current: 6.5A.
At Idle: Draws no more than 90 watts.
Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).
The DSP section shall have the following specifi cations:
EQ: 6 parametric fi lters per channel with adjustable Q, boost/cut ±15 dB. Also
adjustable high and low shelving fi lters.
Filters: Highpass and lowpass per channel. Butterworth 12/18 dB per octave
and Linkwitz-Riley 24 dB per octave. High and low shelving fi lters, one per
channel.
Delay: Up to 50 msec total delay per channel.
Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6,
or ?12 dB threshold per channel.
Presets: 5 user-defi nable loudspeaker presets and 15 factory-default JBL
system presets.
Protection shall include the following:
DSi-Series amplifi ers shall be protected against shorted, open or mismatched
loads; overloaded power supplies; excessive temperature; chain destruction
phenomena; excessive output current, and input overload damage. They also
protect loudspeakers from input/output DC, large or dangerous DC offsets and
turn-on/turn-off transients
The chassis shall be steel. Cooling shall be by a proportional speed fan with
front-to-rear airfl ow.
Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5
in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface.
Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg) | L1400 450W-450W 4ohm (280W-280W8ohm)
COMPACT MODERN DESIGN
Compact size (2U-Rack Height) with up to 1200W per channel@2ohms
these amps save valuable rack space without compromising power output.
HIGH CURRENT TOROIDAL TRANSFORMER
A high-current toroidal transformer saves rack space
and minimizes hum and noise.
EXCELLENT SOUND QUALITY
The low T.H.D.(0.05%) and high damping factor (400 or higher)
gives excellent sound quality.
2 STAGE POWER SUPPLY
The high-power units (L1800 and L2400) have a 2-Stage Class-H design
that maximizes their performance.
EQUIPPED WITH 30Hz or 50Hz HPF
All amplifiers are equipped with high-pass filters on each channel to
help maintain sound quality, yet help protect the loudspeakers.
EXTENSIVE PROTECTION CIRCUITS
Extensive protection circuits monitor over voltage/current conditions, overheating,
output shorts, and DC voltage to improve performance and reliability.
CLIP-LIMITER CIRCUITS
Clip-limiters on each channel are provided to help prevent
distortion due to excessive signal levels.
L.E.D FUNCTION DISPLAYS
Power, Clip limiter, Signal, Protection, Mode (Parallel/Stereo/Bridged)
LEDs on the front panel indicate the status of the unit in operation. |
- Output Power:
500W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD
330W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD
- Bridge Mode, Mono 820W RMS @ 8 Ohms, 1K Hz, 1% THD
- Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)
- Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
- Slew Rate: 15V Per usec
- Damping Factor: @ 8 Ohm: 300
- Impedance: 20 Ohms balanced / 10 Ohms unbalanced
- Cooling System: 2 individual fans
- Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift; Limiter
- build in clip limiter
- Input: XLR 3pin + Jack 6,3mm
- output: Speakon + Binding post
- Dimensions (LxWxH): 360 x 482 x 88mm 2-rack mount spaces
- Weight: 15 KG.
|
Reviews
There are no reviews yet.