| Content |
Broadcaster - ?The Master of the Airwaves?
Like its name suggests this R?DE microphone was specifically designed ?ON-AIR?
applications where wide frequency response and low distortion are demanded.
Winner of the Radio World/US National Association of Broadcasters (NAB) ?What?s
Cool? award in 1998, the Broadcaster has become an industry standard when studio
sound quality is required for on air applications.
Utilizing an Australian designed and manufactured R?DE 1? externally biased condenser
transducers, the Broadcaster features a switch-able high pass filter to remove low frequency
rumble. A unique ?ON-AIR? LED indicator can be switched ?on? or ?off? by shorting contacts
on the 5 pin audio connector. This feature allows console operators to warn the ?Talent?
that the mic is live.
SPECIFICATIONS:
Features:
True condenser transducer On-Air indicator L.E.D. Ultra low noise
Cardioid polar pattern with high 180 rejection Voice tailored Low Cut
Filter Internal Pop Filter Rugged stainless steel body
Acoustic principle: Externally polarised 25mm (1?) condenser
Directional pattern: Cardioid
Frequency range: 20 Hz ~ 20 kHz
Output impedance: 40Ω
Signal noise ratio din iec 651:
>80 dB (1kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 114 dB (per IEC651, IEC268-15)
Power supply voltage: P48, P24 phantom
Weight without battery: 577g
Weight with battery: 1.3kg
Dimensions width: 167mm
Dimensions depth: 50mm
Dimensions height: 50mm
Maximum output voltage: +2 dBu (@ 1% THD into 1kΩ)
| Broadcast sound quality
Low noise circuitry
Internal rechargeable lithium battery, supplying over 150 hours operation
Fully charged in under two hours via MicroUSB
Rugged metal construction
Convenient digital switching
High Frequency Boost
High Pass Filter (Flat/75Hz)
PAD (-10db)
MicroUSB cable included
Ten year extended warranty with online registration
Building on the popularity and acceptance of the RØDE NTG2, the NTG4+ features an all-new condenser capsule with low noise, high sensitivity and the convenience of on-board equalisation/level control via digital switching.
The NTG4+ is the very first microphone to feature an in-built battery that provides 150+ hours of operation with the convenience of USB charging.
Visit the NTG4+ feature page
NTG4+ Specifications
Acoustic Principle Line Gradient
Capsule 0.50“
Polar Pattern Supercardioid
Address Type End
Frequency Range 20Hz - 20kHz(selected HPF @75Hz)
Output Impedance 200Ω
Maximum SPL 135dB SPL (@ 1kHz, 1% THD into 1KΩ load)
Sensitivity -32.0dB re 1 Volt/Pascal (25.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz
Equivalent Noise Level (A-weighted) 16dB-A
Power Options +12V phantom power+24V phantom power+48V phantom powerInternal battery
Weight 176gm
Dimensions 278mmH x 22mmW x 22mmD
Output XLR Output
Warranty 1 year with free extension to 10 years following registration |
This product, like the VideoMic (VM), now the worldʼs biggest selling on camera shotgun microphone, is also destined to become an Industry standard and not only offers the same sound quality & performance as itʼs predecessor, but also meets the industry demand for stereo recording.
Now videographers may use true ʽstudioʼ stereo recording techniques in the field with ease. The X/Y configuration enables the SVM to capture the true ambience of the recording space, while still offering a high level of rear rejection and low noise.
Fitted with a shoe mount, the SVM has the same low noise circuit design as the VM. The SVM offers 9V battery operation, an LED battery status indicator, a high pass filter switch, and a -10dB pad switch which allows for the mic to be used on most cameras with perfect level control.
You can also use the SVM as a remote mic on a stand, or a RØDE boom pole (Optional Accessory), which truly makes this versatile product well suited for all video applications including Electronic News Gathering (ENG), Weddings, Sports Events & Interviews.
Rode Stereo Video Mic Features - Stereo X/Y condenser microphone
- Broadcast sound quality
- Two stp high-pass filter - flat or 80 Hz
- Rugged cast aluminum body
- 9V battery operation
- Custom designed integral windshield
- Low noise circuitry
- Low handling noise
- Integral camera-shoe mount
- Includes Dead Kitten windscreen
- Acoustic Principle: Pressure Gradient
- Directional Pattern: Super Cardioid
- Frequency range: 40 Hz - 20 kHz
- Output Impedance: 200 Ohms
- Signal/Noise Ratio: 74 dB SPL (A - weighted per IEC651)
- Equivalent Noise: 20 dB SPL (A - weighted per IEC651)
- Maximum SPL: 134 dB (@ 1kHz, 1% THD into 1 Ohm load)
- Sensitivity: -38 dB re 1Volt/Pascal (15 mV @ 94 dB SPL) +/- 2 dB @ 1kHz
- Power (Supply voltage): 7 mA, 9 V DC Alkaline Battery, (NSI: 1604A or IEC:6LR61)
- Battery Life: 60+ hours
- Output Connection: Stereo mini jack plug - ø3.5mm (Right Channel - Ring, Left Channel - Tip)
- Dimensions (WxHxD): 6.75 x 3.9 x 2.5 Inches (172 x 100 x 64 mm)
- Weight: .72 lbs (330 grams)
|
The MD 42 is a high-quality reporter's microphone with omni-directional pick-up pattern. It has been specially optimised for rough use in live reporting and broadcasting environments. The MD 42 is a very 'good-natured' microphone whose design avoids wind and handling noise problems. Colour: black, sound inlet basket: refined steel, black.
Features
Two-ply sound inlet basket provides increased protection from wind and pop noise
Rugged metal housing
Rubber mounted capsule (or Elastically mounted capsule) ensures low sensitivity to handling noise
Omni-directional pick-up pattern ensures excellent speech intelligibility without having to point the microphone directly at your interview partner
Pick Up Pattern omni-directional
Frequency response 40 - 18 000 Hz
Sensitivity 2,0 mV/Pa
Ιmpedance 1000 Ohm
Dimensions Ø 49 x 250 mm
Weight 360 gr
|
Element: Externally polarized (DC bias) capacitor
Polar Pattern: Line + gradient
Frequency Response: 20-18,000 Hz
Low Frequency Roll Off: 80 Hz, 12 dB/octave
Open Circuit Sensitivity: -29 dB (35.5 mV) re 1V at 1 Pa
Impedance: 50 ohms
Maximum Input Sound Level: 141 dB SPL, 1 kHz at 1% T.H.D.; 151 dB SPL, with 10 dB pad (nominal)
Dynamic Range: 128 dB, 1 kHz at Max SPL
Signal to Noise Ratio: 81 dB, 1 kHz at 1 Pa
Phantom Power Requiremens: 48V DC, 4.8 mA typical
Weight: 175 g (6.2 oz)
Dimensions: 539.0 mm (21.22“) long, 21.0 mm (0.83“) maximum body diameter
Output Connector: Integral 3-pin XLRM-type
Accessories: AT8405a stand clamp for 5/8“-27 threaded stands; 5/8“-27 to 3/8“-16 threaded adapter; AT8147 windscreen; two O-Rings; protective carrying case
| The RØDE VideoMic is a professional grade 1/2" condenser shotgun microphone designed for use with consumer video cameras and personal audio recorders.
The integrated shock mounting system isolates the VideoMic capsule and electronics from its all-metal shoe mount, providing isolation from external physical factors that may cause unwanted rumble and vibrations in the microphone.
Its standard sized shoe mount also includes a 3/8" thread in the base for easy mounting on a boom pole or stand. (note that cameras with proprietary sized mounts require an additional adaptor.)
Its super cardioid polar pattern is highly directional, focusing on the subject in front of the camera, and minimising any surrounding sounds.
In addition to the microphone's native 40Hz-20kHz response a selectable high-pass filter at 80Hz is available, which will prevent low end noise such as air conditioners and traffic from being recorded.
A -10dB and -20dB level attenuation (or PAD), selectable from inside the battery compartment, allows recording of loud sound sources, such as live music or motorsport.
The RØDE VideoMic directional on-camera microphone is covered by RØDE Microphones' industry leading 10 year warranty.
| Frequency response |
40Hz-20kHz, selectable HPF @ 80Hz/12dB/octave |
| Sensitivity |
-38 dB re 1 Volt/Pascal (15 mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Ιmpedance |
200Ω |
| Τotal harmonic distortion |
134dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Dimensions |
250mm x 65mmx 102mm |
| Weight |
176gm |
|
Reviews
There are no reviews yet.