RODE NTG4+ SUPER CARDIOID SHOTGUN MICROPHONE -USB RECHARGEABLE-

Element: Externally polarized (DC bias) capacitor
Polar Pattern: Line + gradient
Frequency Response: 20-18,000 Hz
Low Frequency Roll Off: 80 Hz, 12 dB/octave
Open Circuit Sensitivity: -29 dB (35.5 mV) re 1V at 1 Pa
Impedance: 50 ohms
Maximum Input Sound Level: 141 dB SPL, 1 kHz at 1% T.H.D.; 151 dB SPL, with 10 dB pad (nominal)
Dynamic Range: 128 dB, 1 kHz at Max SPL
Signal to Noise Ratio: 81 dB, 1 kHz at 1 Pa
Phantom Power Requiremens: 48V DC, 4.8 mA typical
Weight: 175 g (6.2 oz)
Dimensions: 539.0 mm (21.22“) long, 21.0 mm (0.83“) maximum body diameter
Output Connector: Integral 3-pin XLRM-type
Accessories: AT8405a stand clamp for 5/8“-27 threaded stands; 5/8“-27 to 3/8“-16 threaded adapter; AT8147 windscreen; two O-Rings; protective carrying case

Designed for video production and broadcast (ENG/EFP) audio acquisition, the AT8015 provides the narrow acceptance angle desirable for long-distance sound pickup, along with excellent sound rejection from the sides and rear of mic. The roll-off position reduces the pickup of low-frequency ambient noise (such as traffic, air-handling systems, etc.), room reverberation and mechanically coupled vibrations.

Designed for video production and broadcast (ENG/EFP) audio acquisition
Provides the narrow acceptance angle desirable for long-distance sound pickup
Excellent sound rejection from the sides and rear of mic
Switchable low-frequency roll-off
Operates on battery or phantom power
RoHS compliant - free from all substances specified in the EU directive on hazardous substances

Element: Fixed-charge back plate, permanently polarized condenser
Polar Pattern: Line + gradient
Frequency Response: 40-20,000 Hz
Low Frequency Roll Off: 80 Hz, 12 dB/octave
Open Circuit Sensitivity: Phantom: -38 dB (12.5 mV) re 1V at 1 Pa Battery: -39 dB (11.2 mV) re 1V at 1 Pa
Impedance: Phantom: 250 ohms Battery: 300 ohms
Maximum Input Sound Level: Phantom: 132 dB SPL, 1 kHz at 1% T.H.D. Battery: 120 dB SPL, 1 kHz at 1% T.H.D.
Dynamic Range: Phantom: 110 dB, 1 kHz at Max SPL Battery: 98 dB, 1 kHz at Max SPL
Signal to Noise Ratio: 72 dB, 1 kHz at 1 Pa
Phantom Power Requiremens: 11-52V DC, 2 mA typical
Battery Type: 1.5V AA/UM3
Battery Current Life: 0.4 mA / 1200 hours typical (alkaline)
Switch: Flat, roll-off
Weight: 195 g (6.9 oz)
Dimensions: 460.0 mm (18.11“) long, 21.0 mm (0.83“) diameter
Output Connector: Integral 3-pin XLRM-type
Accessories: AT8405a stand clamp for 5/8“-27 threaded stands; 5/8“-27 to 3/8“-16 threaded adapter; AT8135 windscreen; battery; protective carrying case

The new RODE NTG-1 is a lightweight condenser shotgun microphone, specifically
designed for professional applications within the film, video, television, voice-over and
ENG industries.
The NTG-1 provides an electronically balanced output stage and operates on 48 V to
the P48 standard. The NTG-1 offers wide bandwidth and a controlled polar response
coupled with low noise SMT electronics. The NTG-1 is extremely lightweight making it
ideal for mounting directly to video cameras (with optional accessories) or a Boom pole.
The NTG-1 comes complete with mount and windshield. The supplied windscreen effectively
suppresses wind noise when recording outdoors in moderate conditions. Optional accessories
are available for more demanding applications.

SPECIFICATIONS:
Features:
Broadcast sound quality. Low noise circuitry. Condenser transducer. Rugged metal construction.
Low weight: 105 grams approx. . Low handling noise. Supplied with stand mount, zip pouch and
windshield. Designed & manufactured in Australia. Full 2 year guarantee.
Operation power:
The NTG-1 is designed to operate from standard P48 phantom power. The NTG-1 will
operate between 44 V to 52 V applied with positive polarity to pin 2 and pin 3 via the
output XLR connector.
Operation output impedance:
The NTG-1 will operate satisfactorily into a load impedance as low as 1 k§?. If a load below
this is used, the output signal level will be reduced. The NTG-1??s output is balanced between
pin 2 (hot), pin 3 (cold) and pin 1 is ground.
Acoustic principle: Line plus Gradient.
Directional pattern: Super-Cardioid.
Frequency range:
20 Hz ~ 20 kHz selectable HPF @ 80 Hz/12 dB octave
Output impedance:  50 ?
Signal noise ratio din iec 651:
76 dB (1 kHz rel. 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 18 dB SPL (per IEC651, IEC268-15)
Maximum spl: 139 dB (@ 1% THD into 1 k?)
Sensitivity:
-36 dB re 1 Volt/Pascal (15 mV @ 94 dB SPL) +/- 2 dB (at 1 kHz in free field into open circuit)
Dynamic range din iec 651: 121 dB (per IEC651, IEC268-15)
Power supply voltage:  P48 Phantom, 44 V to 52 V
Current consumption:  3.5 mA
Output connection:
3 pin XLR, balanced output between pin 2 (+), pin 3 (-) and pin 1 (ground)
Weight with battery:  105 g approx. 
Dimensions width:  217mm
Dimensions depth:  22mm
Dimensions height: 22mm

The MD 42 is a high-quality reporter's microphone with omni-directional pick-up pattern. It has been specially optimised for rough use in live reporting and broadcasting environments. The MD 42 is a very 'good-natured' microphone whose design avoids wind and handling noise problems. Colour: black, sound inlet basket: refined steel, black.
Features

    Two-ply sound inlet basket provides increased protection from wind and pop noise
    Rugged metal housing
    Rubber mounted capsule (or Elastically mounted capsule) ensures low sensitivity to handling noise
    Omni-directional pick-up pattern ensures excellent speech intelligibility without having to point the microphone directly at your interview partner

Pick Up Pattern omni-directional

Frequency response 40 - 18 000 Hz

Sensitivity 2,0 mV/Pa

Ιmpedance 1000 Ohm

Dimensions Ø 49 x 250 mm

Weight 360 gr

Broadcaster - ?The Master of the Airwaves?

Like its name suggests this R?DE microphone was specifically designed ?ON-AIR?
applications where wide frequency response and low distortion are demanded.
Winner of the Radio World/US National Association of Broadcasters (NAB) ?What?s
Cool? award in 1998, the Broadcaster has become an industry standard when studio
sound quality is required for on air applications.
Utilizing an Australian designed and manufactured R?DE 1? externally biased condenser
transducers, the Broadcaster features a switch-able high pass filter to remove low frequency
rumble. A unique ?ON-AIR? LED indicator can be switched ?on? or ?off? by shorting contacts
on the 5 pin audio connector. This feature allows console operators to warn the ?Talent?
that the mic is live. 

SPECIFICATIONS:
Features:
True condenser transducer On-Air indicator L.E.D. Ultra low noise
Cardioid polar pattern with high 180 rejection Voice tailored Low Cut
Filter Internal Pop Filter Rugged stainless steel body
Acoustic principle: Externally polarised 25mm (1?) condenser
Directional pattern:  Cardioid
Frequency range: 20 Hz ~ 20 kHz
Output impedance:  40Ω
Signal noise ratio din iec 651:
>80 dB (1kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 114 dB (per IEC651, IEC268-15)
Power supply voltage: P48, P24 phantom
Weight without battery: 577g
Weight with battery: 1.3kg
Dimensions width: 167mm
Dimensions depth: 50mm
Dimensions height: 50mm
Maximum output voltage: +2 dBu (@ 1% THD into 1kΩ)