| Content | Broadcast sound quality
Low noise circuitry
Internal rechargeable lithium battery, supplying over 150 hours operation
Fully charged in under two hours via MicroUSB
Rugged metal construction
Convenient digital switching
High Frequency Boost
High Pass Filter (Flat/75Hz)
PAD (-10db)
MicroUSB cable included
Ten year extended warranty with online registration
Building on the popularity and acceptance of the RØDE NTG2, the NTG4+ features an all-new condenser capsule with low noise, high sensitivity and the convenience of on-board equalisation/level control via digital switching.
The NTG4+ is the very first microphone to feature an in-built battery that provides 150+ hours of operation with the convenience of USB charging.
Visit the NTG4+ feature page
NTG4+ Specifications
Acoustic Principle Line Gradient
Capsule 0.50“
Polar Pattern Supercardioid
Address Type End
Frequency Range 20Hz - 20kHz(selected HPF @75Hz)
Output Impedance 200Ω
Maximum SPL 135dB SPL (@ 1kHz, 1% THD into 1KΩ load)
Sensitivity -32.0dB re 1 Volt/Pascal (25.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz
Equivalent Noise Level (A-weighted) 16dB-A
Power Options +12V phantom power+24V phantom power+48V phantom powerInternal battery
Weight 176gm
Dimensions 278mmH x 22mmW x 22mmD
Output XLR Output
Warranty 1 year with free extension to 10 years following registration |
Based on models originally developed for use in the broadcast of the Sydney Olympics in 2000, the BP4027 (14.96" long) and BP4029 (9.29" long) Stereo Shotgun models are engineered for high-end broadcast and production use. Both microphones feature independent line-cardioid and figure-of-eight elements configured in an MS (Mid-Side) arrangement with switch-selectable internal matrixing. These innovative microphones allow sound recordists the choice of selecting a left-right stereo output (wide or narrow) via the microphone's internal matrixing system or choosing discreet Mid-Side signals for later manipulation, a flexibility not available from any other manufacturer. A switchable low frequency roll-off filter helps minimize the pickup of unwanted low frequency noise. These phantom-powered models feature a rugged lightweight design and sleek black color scheme, perfect for on-camera use.
Designed for broadcasters, videographers and sound recordists
Compact, lightweight design is perfect for camera-mount use
Independent Line-cardioid and Figure-of-eight condenser elements
Switchable low-frequency roll-off
Switch selection of non-matrixed M-S mode and two internally-matrixed left/right stereo modes
Includes a 0.61 m (24“) cable (5-pin XLRF to two standard 3-pin XLRM connectors)
RoHS compliant - free from all substances specified in the EU directive on hazardous substances
Frequency Response: 30-20,000 Hz
Low Frequency Roll Off: 80 Hz, 12 dB/octave
Open Circuit Sensitivity: Mid: -30 dB (31.6 mV) re 1V at 1 Pa; Side: -34 dB (19.9 mV) re 1V at 1 Pa; LR Stereo: -36 dB (15.8 mV) re 1V at 1 Pa
Impedance: 200 ohms
Maximum Input Sound Level: Mid: 123 dB SPL, 1 kHz at 1% T.H.D.; Side: 127 dB SPL, 1 kHz at 1% T.H.D.; LR Stereo: 126 dB SPL, 1 kHz at 1% T.H.D.
Dynamic Range: Mid: 101 dB, 1 kHz at Max SPL; Side: 101 dB, 1 kHz at Max SPL; LR Stereo: 102 dB, 1 kHz at Max SPL
Signal to Noise Ratio: Mid: 72 dB SPL, 1 kHz at 1 Pa; Side: 68 dB SPL, 1 kHz at 1 Pa; LR Stereo: 70 dB SPL, 1 kHz at 1 Pa
Phantom Power Requiremens: 11-52V DC, 4 mA typical at 48V, each channel
Weight: 142 g (5.0 oz)
Dimensions: 380.0 mm (14.96“) long, 21.0 mm (0.83“) diameter
Output Connector: Integral XLR5M-type
Cable: Dual 0.61 m (24“) shielded two-conductor, terminated in two XLR3M-type connectors
Accessories: AT8405a stand clamp for 5/8“-27 threaded stands; AT8135 foam windscreen; 5/8“-27 to 3/8“-16 threaded adapter; protective carrying case
|
The MD 42 is a high-quality reporter's microphone with omni-directional pick-up pattern. It has been specially optimised for rough use in live reporting and broadcasting environments. The MD 42 is a very 'good-natured' microphone whose design avoids wind and handling noise problems. Colour: black, sound inlet basket: refined steel, black.
Features
Two-ply sound inlet basket provides increased protection from wind and pop noise
Rugged metal housing
Rubber mounted capsule (or Elastically mounted capsule) ensures low sensitivity to handling noise
Omni-directional pick-up pattern ensures excellent speech intelligibility without having to point the microphone directly at your interview partner
Pick Up Pattern omni-directional
Frequency response 40 - 18 000 Hz
Sensitivity 2,0 mV/Pa
Ιmpedance 1000 Ohm
Dimensions Ø 49 x 250 mm
Weight 360 gr
| The RØDE VideoMic is a professional grade 1/2" condenser shotgun microphone designed for use with consumer video cameras and personal audio recorders.
The integrated shock mounting system isolates the VideoMic capsule and electronics from its all-metal shoe mount, providing isolation from external physical factors that may cause unwanted rumble and vibrations in the microphone.
Its standard sized shoe mount also includes a 3/8" thread in the base for easy mounting on a boom pole or stand. (note that cameras with proprietary sized mounts require an additional adaptor.)
Its super cardioid polar pattern is highly directional, focusing on the subject in front of the camera, and minimising any surrounding sounds.
In addition to the microphone's native 40Hz-20kHz response a selectable high-pass filter at 80Hz is available, which will prevent low end noise such as air conditioners and traffic from being recorded.
A -10dB and -20dB level attenuation (or PAD), selectable from inside the battery compartment, allows recording of loud sound sources, such as live music or motorsport.
The RØDE VideoMic directional on-camera microphone is covered by RØDE Microphones' industry leading 10 year warranty.
| Frequency response |
40Hz-20kHz, selectable HPF @ 80Hz/12dB/octave |
| Sensitivity |
-38 dB re 1 Volt/Pascal (15 mV @ 94 dB SPL) +/- 2 dB @ 1kHz |
| Ιmpedance |
200Ω |
| Τotal harmonic distortion |
134dB SPL (@ 1kHz, 1% THD into 1KΩ load) |
| Dimensions |
250mm x 65mmx 102mm |
| Weight |
176gm |
|
The CS-50 is a compact, light-weight stereo condenser microphone designed for the R-4 and R-4 Pro, videographer, broadcaster, and sound designer. The CS-50 features bass roll-off capability as well as selectable wide stereo or narrow (focused) polar patterns.
From Edirol, the CS-50 Stereo Microphone is designed for use with the Edirol/Roland R4 portable digital field recorder. The microphone features wide stereo and narrow polar patterns. The wide stereo pattern reproduces audio with accurate stereo imaging while the mono pattern is focused and reduces signal at the sides of the capsule. The CS-50 features a low frequency roll-off switch for eliminating hum and low-frequency noise due to wind or proximity effect. A dual XLR output cable is supplied.
Wide Stereo PatternThe wide stereo pattern provides a generous pick up area while reproducing signal with accurate stereo placement. This setting is ideal for ambiance capturing, live music, sound effects, etc.Mono (Narrow) PatternThe narrow pattern provides a focused pick up at the front end of the capsule. The result is an accurate signal without noise at the off-axis sections of the capsule.Low Frequency Roll-OffThe low-frequency roll-off switch eliminates hum and low-frequency noise due to wind, handling and proximity effect.Light Weight ProfileThe light weight, slim profile make the CS-50 ideal for location use while mounted on a boom, pistol grip or camera.
What's in the Box:
- Windscreen
- Desktop Prop
- Mic Stand Adapter
- L/R XLR Cable 6.56 feet (2m)
- Soft case
- 1 Year Warranty
Specifications: | ransducer | Back Electret Condenser | | Polar Pattern | Line Cardioid | | Frequency Response |
50 - 20,000Hz
| | Open Circuit Sensitivity | 14.9 mV/Pa, -36.5 dBV @ 1 Pa | | Dynamic Range (Typical) | Not Specified by Manufacturer | | Signal-to-Noise Ratio | Greater than 70dB (at 1kHz/1Pa) | | Maximum Input Sound Level | 126dB S.P.L (at 1kHz, 1% T.H.D. Typical) | | Power Requirements | 48V Phantom x 2ch | | Output Impedance | 200 Ohms | | Current Consumption | 3.8 mA (Typical) | | Output Connectors | 3-pin XLR | | Pad | No | | Low Frequency Roll-Off | Yes | | Dimensions | Not Specified by Manufacturer | | Weight | 2.92 oz (83g) |
| The R?DE VideoMic is a professional grade shotgun microphone. Based on the
latest ?Film industry? technology, the VideoMic is designed specifically for use with
high quality Digital Video Cameras.
The microphone exhibits low noise and an unusually wide bandwidth for its size. It
is ultra lightweight, yet rugged due to it?s ABS construction. The VideoMic is powered
by a standard 9 V battery and offers a Low Battery LED status indicator and a
switchable high pass filter to reduce unwanted low frequency rumble.
The VideoMic attaches to any Camcorder that has the standard camera-shoe fitting
and utilizes a stereo mini jack for audio output.
SPECIFICATIONS:
Features:
Studio recording quality. Rugged fibre-reinforced ABS construction. 9 V battery operation.
Custom designed integral wind shield. Condenser Microphone. Low noise circuitry. Low
handling noise. Integral camera-shoe mount. Designed & manufactured in Australia.
Full 2 year guarantee.
Operation power:
The VideoMic is designed to operate from a 9 V battery (ANSI:1604A or IEC:6LR61).
The battery is conveniently located within the support arm of the microphone. A fully
removable access cover and a 1-way insertion mechanism ensure ease of loading.
The battery will provide more than 100 hrs. of continuous use due to a low consumption
of only 5.0 mA.
Operation output impedance:
The microphone will operate satisfactorily into a load impedance as low as 1 k?.
If a load below this is used, the output signal level will be reduced.
Acoustic principle: Line plus Gradient
Directional pattern: Super-Cardioid
Frequency range:
40 Hz ~ 20 000 Hz selectable HPF @ 80 Hz/12 dB/octave
Output impedance: 200 Ω
Signal noise ratio din iec 651:
74 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 20 dB SPL (per IEC651, IEC268-15)
Maximum spl: 134 dB (@ 1% THD into 1 kΩ)
Sensitivity:
-38 dB re 1 Volt/Pascal (15 mV @ 94 dB SPL) +/- 2 dB (at 1 kHz in free field into open circuit)
Dynamic range din iec 651: 114 dB (per IEC651, IEC268-15)
Power supply voltage:
9 V DC Alkaline Battery (ANSI:1604A or IEC:6LR61)
Current consumption: 5 mA
Battery life: >100 hours
Output connection: Stereo mini jack plug - ?3.5 mm.
Weight: 176 grm.
Dimensions width: 250mm
Dimensions depth: 65mm
Dimensions height: 102mm |
Reviews
There are no reviews yet.