| Content |
NT2-A - ?The Legend Continues? Multi Pattern 1? Condenser Microphone.
The new NT2-A carries on the tradition forged by the now legendary R?DE NT2.
A professional large capsule (1?) studio microphone incorporating three-position
pick-up patterns, pad and high pass filter switches conveniently located on the
mic body.
At the heart of the NT2-A is the Australian designed and manufactured HF1 dual
diaphragm capsule. The frequency and transient response of this new transducer
has been voiced to complement today?s modern recording techniques, and yet still
evoke the silky smooth character of the legendary microphones of the 50?s and 60?s.
These features provide the flexibility and superlative audio characteristics that make
the NT2-A one of the most versatile condenser mics available.
The NT2-A?s variable controls allow switching between Omni, Figure 8, and Cardioid
polar patterns. The three position high-pass filter provides a flat response or an 80Hz
and 40Hz high pass filter to be selected. Finally the microphones Pad can be switched
between 0 dB, -5dB and -10dB. The NT2-A comes in a soft pouch with an M2 stand mount.
SPECIFICATIONS:
Features:
The Australian designed and manufactured HF1 1? edge terminated, gold sputtered, dual
5 um diaphragm capsule. 3-position variable polar pattern: Omni, Cardioid & Figure 8; all
controlled on the mic. 3-position variable high-pass filter: Flat, 80 Hz or 40 Hz. 3-position
variable pad: 0 dB, -5 dB or -10 dB. Ultra low noise, transformerless SMT circuitry. Wide
dynamic range. High strength heat-treated steel mesh head. Durable satin nickel finish.
Internal capsule shock mounting. Supplied complete with soft pouch and clip. Designed
and manufactured in Sydney, Australia.
Operation power:
The NT2-A is designed to operate from phantom power to the P48 standard. The NT2-A will
operate between 44V and 52V applied with positive polarity to pin 2 and pin 3 of the output
XLR connector.
Operation output impedance:
The NT2-A will operate satisfactorily into a load impedance as low as 1 kΩ. If a load below this
is used, the output signal level will be reduced. The NT2-A output is balanced between pin 2 (hot)
and pin 3 (cold). Pin 1 is ground.
Acoustic principle: Externally polarized 25 mm (1?) dual diaphragm.
Directional pattern: Multi-pattern
Frequency range: 20 Hz ~ 20 000 Hz
Output impedance: 200 Ω
Signal noise ratio din iec 651:
87 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 7 dBA SPL (per IEC651, IEC268-15)
Maximum spl:
147 dB (@ 1% THD into 1 kΩ); 157 dB (@ 1% THD into 1 kΩ) - pad at maximum
Sensitivity: -36 dB re 1 Volt/Pascal; (16 mV @ 94 dB SPL) +/-2 dB
Dynamic range din iec 651: 140 dB (per IEC651, IEC268-15)
Power supply voltage: 48 Volts (P48)
Output connection:
3 pin XLR, balanced output between; pin 2(+) and pin 3(-); Pin 1 ground
Weight with battery: 860 grm | Behringer C-1 Studio Condenser Microphone
Behringer C-1 Studio Condenser Microphone
The C-1 Studio Condenser Microphone from Behringer offers a cardioid pickup pattern for maximum sound source separation and feedback rejection. This low noise microphone is suitable for a wide range of recording scenarios, including project, professional, and home studio applications. There is a pressure gradient transducer and a shock-mounted large diaphragm capsule for open, transparent sound with high-quality transient response. It is constructed of a die-cast metal body for durability and features an LED light to indicate when the microphone is receiving phantom power. The C-1 includes a swivel mount and custom case.
- Professional large-diaphragm condenser microphone for unsurpassed audio quality
- Ideal as main and support microphone for studio and live applications
- Exceptionally flat frequency response and ultra-high sound resolution
- Cardioid pickup pattern for outstanding sound source separation and feedback rejection
- Ultra low-noise transformerless FET input circuitry
- LED indicates phantom power operation
- Gold-plated 3-pin XLR output connector for perfect signal transmission
- Ultra-rugged construction with die-cast body
- Swivel stand mount and carrying case included
| Operating Principle |
Pressure Gradient |
| Capsule |
Condenser |
| Diaphragm |
0.63" / 16.0 mm |
| Polar Pattern |
Cardioid |
Performance
| Frequency Range |
40 Hz to 20 kHz |
| Maximum SPL |
136 dB SPL |
| Impedance |
100 Ohms |
| Load Impedance |
1000 Ohms |
| Sensitivity |
-33 dB |
| THD |
1% |
Connectivity
| Output Connectors (Analog) |
1 x XLR 3-Pin |
Power
| Operating Voltage |
36 to 52 V |
| Operating Current Consumption |
2.5 µA |
Physical
0.93 lb / 0.42 kg
| Dimensions |
ø: 2.13 x L: 7.09" / ø: 54 x L: 180 mm |
| Weight |
|
|
| Acoustical operating principle | Pressure gradient transducer | | Directional pattern | Cardioid | | Frequency range | 20 Hz ... 20 kHz | | Sensitivity at 1 kHz into 1 kohm | 13 mV/Pa | | Rated impedance | 50 ohms | | Rated load impedance | 1000 ohms | | Equivalent noise level, CCIR1) | 23 dB | | Equivalent noise level, A-weighted1) | 12 dB-A | | Signal-to-noise ratio, CCIR1) (rel. 94 dB SPL) | 71 dB | | Signal-to-noise ratio, A-weighted1) (rel. 94 dB SPL) | 82 dB | | Maximum SPL for THD | 110 dB | | Maximum SPL for THD | 129 dB | | Maximum output voltage for THD | -1 dBu | | Dyn. range of the mic. amplifier /A-weighted, 0.5 %2)) | 98 dB | | Dyn. range of the mic. amplifier /A-weighted, 5 %2)) | 117 dB | | Supply voltage (P48, IEC 61938) | 48 V ± 4 V | | Current consumption (P48, IEC 61938) | 3.2 mA | | Matching connector | XLR 3F | | Weight | 825 g | | Diameter | 78 mm | | Length | 165 mm |
1) According to IEC 60268-1; CCIR-weighting according to CCIR 468-3, quasi peak; A-weighting according to IEC 61672-1, RMS
2) Measured as equivalent el. input signal |
|
|
Behringer B-5 Sputtered Diaphragm Studio Condenser Microphone
The B-5 is a professional gold-sputtered diaphragm condenser microphone featuring two interchangeable capsules for different pickup patterns (cardioid and omnidirectional). It is perfect for acoustic instruments, vocals and overhead miking. Its ultra low-noise transformerless FET input eliminates low frequency distortion. The -10 dB attenuator can be used with high volume signal sources, while the low-cut filter eliminates floor rumble. The microphone is delivered in a rugged hard case with stand adapter and windscreen.
|
|
|
|
|
|
|
Professional true condenser microphone for studio and live applications
|
|
|
2 interchangeable capsules with cardioid and omnidirectional pickup patterns
|
|
|
Low-mass gold sputtered diaphragm for ultimate sound reproduction
|
|
|
Perfect for acoustic instruments, voice and overhead etc.
|
|
|
Ultra low-noise transformerless FET input eliminates low-frequency distortion
|
|
Smooth, super-wide frequency response and incredible musicality
|
|
Switchable low-frequency roll-off and -10 dB input attenuation
|
|
Gold-plated 3-pin XLR output connector
|
|
Rugged construction with satin nickel-plated brass body
|
|
Custom microphone stand adapter, windscreen and transport case included
|
|
Manual Download | Behringer C-2 2 Matched Studio Condenser Microphones
2 Matched Studio Condenser Microphones
- 2 matched condenser microphones for stereo studio recording and live applications
- Ideal as main and support microphones for studio and live applications
- Cardioid pickup pattern for effective feedback elimination
- Low-mass diaphragm for ultra-wide frequency response and ultimate sound reproduction
- Switchable low-frequency roll-off and input attenuation
- Ultra low-noise transformerless FET input eliminates low-frequency distortion
Excellent Source Isolation
Our C-2 mics also feature a low-frequency rolloff switch to eliminate infrasonics (mic handling noise, sound created by creaky stages), as well as a switchable -10 dB input pad to accommodate hot signals, such as a really loud vocalist or overzealous cellist.
The cardioid pickup pattern provides unparalleled sound source separation and feedback rejection. C-2 mics contain ultra low-noise transformerless FET input circuitry that can handle extreme dynamics with a maximum sound pressure level of 136 dB. So even if the featured performer at your next recording session or live show happens to be a revved-up jet engine, this workhorse mic will not distort!
Sound That Astounds
Every stitch of these mics is designed to deliver beautiful sound. Beginning with the gold-plated 3-pin XLR connector, you get the highest signal integrity.
Once connected to your system, youʼll notice these twin pro-caliber microphones have a 4 dB boost in the 1 kHz - 8 kHz range. For those of you new to condenser mics, this basically means youʼll get a slightly brighter sound that will give the perfect shape to cymbals and overhead miking. Acoustic pianos and choirs also benefit greatly from this type of frequency response.
Excellent Source Isolation
The cardioid pickup pattern provides unparalleled sound source separation and feedback rejection. C-2 mics contain ultra low-noise transformerless FET input circuitry that can handle extreme dynamics with a maximum sound pressure level of 136 dB. So even if the featured performer at your next recording session or live show happens to be a revved-up jet engine, this workhorse mic will not distort!
Our C-2 mics also feature a low-frequency rolloff switch to eliminate infrasonics (mic handling noise, sound created by creaky stages), as well as a switchable -10 dB input pad to accommodate hot signals, such as a really loud vocalist or overzealous cellist.
You Are Covered
We always strive to provide the best possible Customer Experience. Our products are made in our own MUSIC Group factory using state-of-the-art automation, enhanced production workflows and quality assurance labs with the most sophisticated test equipment available in the world.
As a result, we have one of the lowest product failure rates in the industry, and we confidently back it up with a generous 3-Year Warranty program. |
Rode's new NTK has the quality and warmth demanded from a tube mic.
With the large 1 in. capsule gold-plated membrane and twin triode tubes
(hand graded and selected), Rode is again setting the standard for value.
This is a tube mic designed exclusively for recording professionals who
want what only the best can offer.
Features:
Dynamic range of 47dB
Ultra low noise of only 12dB
Internal capsule shock mounting
Cardioid polar pattern
20Hz - 20kHz frequency response
Includes a power supply, 30 ft. cable, and stand adapter
Technical Description:
Capsule: Externally polarised 1 in. pressure-gradient condenser
Active Electronics: Unity-gain closed-loop impedance converter;
vacuum-tube input with bipolar buffering
Pickup Pattern: Cardioid
Frequency Response: 20Hz - 20kHz (+/-6dB)
Output Impedance: 200 ohms (100 ohms per leg)
Sensitivity: -38dB re 1V/Pa (12mV @ 94dB SPL) +/-1dB
Equivalent Noise: 12dB SPL (A-weighted per IEC268-15) +/-2dB
Maximum Output: > +29dBu (@ 1kHz, 5% THD into 1k (load)
Dynamic Range: > 147dB (A-weighted, per IEC268-15)
Maximum SPL: > 158dB SPL (@ 1kHz, 5% THD into 1k (load)
Signal/Noise Ratio: > 82dB (A-weighted, per IEC268-15)
External power supply: 100-120V/200-240V AC (user selectable)
50Hz/60Hz, 25VA maximum
Packed Weight: 4.53 kg (Mic only 760 gm)
Accessories included:
Power Supply
30 ft (10 m) Multicore Cable
M2 Standmount plus 3/8-5/8 in. Thread Adapter
Optional Extras: SM2 Shockmount
|
Reviews
There are no reviews yet.