Content |
Wireless microphone handheld transmitter with mute switch and condenser super-cardiod capsule
- Transmission type: 2.4GHz fixed frequency agile system
- Power source: 2 x AA 1.5v Batteries or RØDE LB-1 4.2v Lithium-Ion Rechargeable Battery or 5v USB
- Antenna: diversity antenna located at the bottom of TX-M2
- Dimensions: 40mm x 256mm x 40mm
- Weight: 222g
Delivery includes:
- TX-M2 Handheld transmitter
- LB-1 4.2v Lithium-Ion Rechargeable Battery
- ZP-2 Padded zip pouch
- Microphone clip
- Micro USB charging cable
| OLED display (on receiver)
One button pairing
Three level gain control
AA battery or USB powered
Includes RØDE\'s broadcast Lavalier microphone
RØDELink represents the next generation of digital wireless systems. Using a series II 2.4GHz digital transmission with 128-bit encryption, it is able to constantly monitor and hop between frequencies to maintain the strongest possible signal level at a range of up to 100 metres (over 100 yards). The RØDELink Filmmaker Kit provides everything you need to start shooting video wirelessly, including a receiver, transmitter and broadcast-grade lavalier microphone. The receiver (RX-CAM) features an OLED display with information on level, battery status (receiver and transmitter), mute and channel selection. The unit can be mounted on a standard camera shoe mount, 3/8" thread or belt-clip, and for added versatility the shoe mount can be located in one of two positions. The lightweight transmitter (TX-BELT) can be fitted to a belt or clothing and features a locking thread to ensure the microphone connection is as secure as possible. RØDEʼs omnidirectional Lavalier microphone is included in the kit to provide the highest possible audio reproduction quality.
RØDELink Filmmaker Kit Specifications
Transmission type 2.4GHz Fixed Frequency Agile System
System dynamic range 112dB
Range (distance) 100m
Frequency range 35Hz - 22kHz
Maximum output level 1v Rms (2.8v P-p)
Max input signal level 1v Rms (2.8v P-p)
Max latency 4ms
Receiver (RX-CAM)
Power source 2 X AA Battery Or MicroUSB
Antenna Internal
Output connection 3.5mm TRS Locking Jack Socket - Dual Mono
Output impedance 300Ω
Dimensions 111mm X 65mm X 52mm
Weight 190gm
Transmitter (TX-BELT)
Power source 2 X AA Battery Or MicroUSB
Antenna Internal
Output connection 3.5mm TRS Locking Jack Socket
Output impedance 10kΩ
Dimensions 111mm X 65mm X 40mm
Weight 190gm
Lavalier
Acoustic Principle Pressure Gradient
Active Electronics JFET impedance converter
Capsule 0.10“
Address Type End
Frequency Range 60Hz - 18kHz
Output Impedance 3000Ω
Maximum SPL 110dB SPL (@ 1kHz, 1% THD into 1KΩ load)
Maximum Output Level 189.0dBu (@ 1kHz, 1% THD into 1KΩ load
Sensitivity -33.5dB re 1 Volt/Pascal (21.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz
Equivalent Noise Level (A-weighted) 25dB-A
Weight 1.00gm
Dimensions 12.00mmH x 4.50mmW x 4.50mmD
Warranty 10 year warranty |
Broadcast sound quality
Low noise circuitry
Rugged metal construction
Convenient digital switching
High Frequency Boost
High Pass Filter (Flat/75Hz)
PAD (-10db)
Ten year extended warranty with online registration
The NTG4 builds on the platform created by RØDE's award-winning NTG1 shotgun microphone. A broadcast-quality directional condenser microphone designed to provide premium audio recording in a versatile range of applications including on-camera and boom mounted.
Visit the NTG4 feature page
NTG4 Specifications
Acoustic Principle Line Gradient
Capsule 0.50“
Polar Pattern Supercardioid
Address Type End
Frequency Range 20Hz - 20kHz(selected HPF @75Hz)
Output Impedance 200Ω
Maximum SPL 135dB SPL (@ 1kHz, 1% THD into 1KΩ load)
Sensitivity -32.0dB re 1 Volt/Pascal (25.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz
Equivalent Noise Level (A-weighted) 16dB-A
Power Options +12V phantom power+24V phantom power+48V phantom power
Weight 126gm
Dimensions 225mmH x 22mmW x 22mmD
Output XLR Output
Warranty 1 year with free extension to 10 years following registration
|
The length (14.53“) of the AT8035 Line + Gradient Condenser Microphone is well-suited for ENG, outdoor recording and other specialized uses. The microphone is designed for video production and broadcast (ENG/EFP) audio acquisition. Suited for both boom & handheld use, it provides the narrow acceptance angle desirable for long-distance sound pickup, featuring excellent sound rejection from the sides and rear of mic and switchable low-frequency roll-off. It operates on battery or phantom power.
Designed for video production and broadcast (ENG/EFP) audio acquisition
Length is well-suited for ENG, outdoor recording and other specialized uses
Provides the narrow acceptance angle desirable for long-distance sound pickup
Excellent sound rejection from the sides and rear of mic
Switchable low-frequency roll-off
Operates on battery or phantom power
RoHS compliant - free from all substances specified in the EU directive on hazardous substances
Element: Fixed-charge back plate, permanently polarized condenser
Polar Pattern: Line + gradient
Frequency Response: 40-20,000 Hz
Low Frequency Roll Off: 80 Hz, 12 dB/octave
Open Circuit Sensitivity: Phantom: -38 dB (12.5 mV) re 1V at 1 Pa Battery: 39 dB (11.2 mV) re 1V at 1 Pa
Impedance: Phantom: 250 ohms Battery: 300 ohms
Maximum Input Sound Level: Phantom: 132 dB SPL, 1 kHz at 1% T.H.D. Battery: 120 dB SPL, 1 kHz at 1% T.H.D.
Dynamic Range: Phantom: 110 dB, 1 kHz at Max SPL Battery: 98 dB, 1 kHz at Max SPL
Signal to Noise Ratio: 72 dB, 1 kHz at 1 Pa
Phantom Power Requiremens: 11-52V DC, 2 mA typical
Battery Type: 1.5V AA/UM3
Battery Current Life: 0.4 mA / 1200 hours typical (alkaline)
Switch: Flat, roll-off
Weight: 170 g (6.0 oz)
Dimensions: 369.0 mm (14.53“) long, 21.0 mm (0.83“) diameter
Output Connector: Integral 3-pin XLRM-type
Accessories: AT8405a stand clamp for 5/8“-27 threaded stands; 5/8“-27 to 3/8“-16 threaded adapter; AT8132 windscreen; battery; protective carrying case
|
ProMic Laser is our first ever DSLR on-camera microphone - a shotgun condenser microphone with a precision-tuned capsule for capturing professional-quality audio direct to camera.
With more and more video recording enthusiasts taking an increased interest in the quality of the audio of their videos, ProMic Laser provides the high-quality audio to match the high-definition video capabilities of todayʼs DSLR cameras.
Laser, the first release in the ProMic series, is a truly professional solution. It has a rugged aluminium design and comes with a removable wind shield and a custom shockmount for hot-shoe mounting directly onto a DSLR camera.
Laser is battery-powered using a single AAA battery (not included), which means that the microphone has an increased sensitivity level, and a lower noise floor, but the inclusion of a -10dB Pad allows you to reduce the level of the mic for recording louder sources.
The microphone also features a Bass Cut, which gives you the option of removing unwanted low frequency rumble, such as traffic or noise from the camera itself, and this can be used in tandem with the -10dB Pad.
As with all sE Electronics products, ProMic Laser comes with a three-year free replacement warranty, which means if it lets you down, weʼll simply give you a new one.
ProMic Laser comes with a protective carry bag and a 3.5mm coiled jack-to-jack cable to connect the microphone to your camera. Laser is compatible with the upcoming ProMic accessories series, which includes boom poles and fur windshields. |
Clear, directional audio on the GO!
Compact and light weight by design, the VideoMic GO delivers clear, crisp, directional audio with incredible ease of use. Its tight pickup area focuses directly in front of the microphone and reduces other surrounding sounds, ensuring that your subject is isolated from distracting background noise.
The integrated Rycote® Lyre® shock mount isolates your microphone from bumps and vibrations that could otherwise interfere with your sound.
Constructed from a single piece of hard-wearing thermoplastic, the Lyre® provides superior acoustic suspension to traditional elastic solutions, and will never wear out, sag or snap.
The VideoMic GO has no complicated switches or settings and is powered by your camera's external microphone input, requiring no batteries to operate, ensuring you never miss a great shot.
Acoustic Principle Line Gradient
Frequency Range 100Hz ~ 16,000Hz
Equivalent Noise 34dBA SPL (A - weighted per IEC651)
Signal Noise 60dB SPL (A - weighted per IEC651)
Power Required Plug-in power required (330uA @ 2.5V)
Dimensions 167mmL x 79mmH x 70mmD
Directional Pattern Super-Cardioid
Sensitivity -35dB re 1V/Pa (17.8mV @ 94dB SPL) ±2dB @ 1kHz
Maximum SPL 120dB (@ 1kHz, 1% THD into 1kΩ load)
Dynamic Range 96dB (per IEC651)
Output Connection 3.5mm stereo mini-jack
Weight 73g
|
Reviews
There are no reviews yet.