The Servo 300 is a great choice for powering a small to medium sized PA, or an intergrated conference room audio system. The Servo 300 features large 10-segment 3-color level LED meters and independent channel volume controls. The rear panel includes 1/4-inch balanced and RCA input connectors, as well as 5-way binding post and 1/4-inch […]
The Servo 300 is a great choice for powering a small to medium sized PA, or
an intergrated conference room audio system.
The Servo 300 features large 10-segment 3-color level LED meters and independent
channel volume controls. The rear panel includes 1/4-inch balanced and RCA
input connectors, as well as 5-way binding post and 1/4-inch speaker outputs.
The Servo amp line also features a 4-stage power protection circuitry that ensures
optimal performance and protection of connected components.
FEATURES:
150 watts per side at 4 ohms
300 watts bridged mono at 8 ohms
1/4-inch and RCA input connectors
5-way binding post and 1/4-inch outputs
Dual Rack space design
10-segment, 3-color Level LED meters
4-stage power protection circuitry
Weight
9.07 kg
Reviews
There are no reviews yet.
Be the first to review “SAMSON SERVO 300 2X150W POWER AMPLIFIER” Cancel reply
The Servo 300 is a great choice for powering a small to medium sized PA, or
an intergrated conference room audio system.
The Servo 300 features large 10-segment 3-color level LED meters and independent
channel volume controls. The rear panel includes 1/4-inch balanced and RCA
input connectors, as well as 5-way binding post and 1/4-inch speaker outputs.
The Servo amp line also features a 4-stage power protection circuitry that ensures
optimal performance and protection of connected components.
FEATURES:
150 watts per side at 4 ohms
300 watts bridged mono at 8 ohms
1/4-inch and RCA input connectors
5-way binding post and 1/4-inch outputs
Dual Rack space design
10-segment, 3-color Level LED meters
4-stage power protection circuitry
These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.
Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 650 W, 4 Ω - 450 W, 8 Ω - 270 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 1150 W, 4 Ω - 660 W, 8 Ω - 350 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 1300 W, 8 Ω - 900 W Input Sensitivity, rated power @ 8 Ω, 1 kHz + 2,2 dBu (1,0 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class AB Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 12.6 kg (27.8 lbs)
The LD Systems DP600 Power Amplifier offers an amplifiying level of 2 x 300 W 2 Ohm
The new DEEP2 amp series features four class-H power amplifiers with toroidal core offering amplifying levels from 2 x 400 W till 2 x 810 W at 4 Ohm. During the development of this series we attached a great importance to the reliability and the durability of the amps in continuous operation, this is why we used exclusively high end and selected components for the construction of these products.
The DEEP2 series features a Clip Limiter as well as every common protection circuits. These amps are 2 Ohm and 4 Ohm (bridge) stable in continuous operation. On the rear panel you will find all the common In- and Outputs.
The DEEP2 series will convince every user thanks to a dynamic and very clear sound which is perfectly adapted for Subbass applications as well as for multifunctional speakers. All models are lightweight and feature a robust steel plate housing and a very user friendly and compact design.
The DEEP2 series will prove to be a profitable and reliable choice for bands, renting companies and professional users thanks to its excellent price/performance ratio.
Product type
Power Amplifiers
Type
PA Power Amplifiers
Rated ouput power (1kHz @ 2 Ohms)
2 x 300 W
Rated ouput power (1kHz @ 4 Ohms)
2 x 400 W
Rated ouput power (1kHz @ 8 Ohms)
2 x 300 W
Rated ouput power (1kHz @ 4 Ohms, bridged)
600 W
Rated ouput power (1kHz @ 8 Ohms, bridged)
800 W
Output circuitry
Class H
Frequency response
20 - 20000 Hz
THD
< 0.1 %
Signal-to-noise ratio
105 dB
Damping factor
> 400
Crosstalk
>80 dB
Gain
35 dB
Input sensitivity
0.75 V
Protection circuits
clip limiter , DC protection , short circuit , thermal overload
level , Limit , Power , Protect (protection circuit engaged) , Signal
Loudspeaker outputs
2
Speaker output connections
Speakon compatible , Terminal posts
Cooling
highly efficient, automatic
Operating voltage
transformer
Operating voltage
230 V AC / 50-60 Hz
Weight
12,8 kg
Features
Volex mains socket
The high efficiency of the ED series enables maximum efficiency with low heat generation.
A new and unique Class-H circuity technology using state of the art SMD Surface Mount Technology with a reduced number of components offering performance levels exceeding audiophile levels like a slew rate of 50V/µs and high-end extended dynamic sound. The amplifier provides 2x300W into 4 Ohm is equipped complete with temperature-controlled fan cooling, all common protective circuits such as over-temperature, short circuit, RFI and soft start.
The integral soft clip limiter protects against damage to the connected loudspeakers, the activity of a protective circuit, signal and limiter are shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS
Power output stereo 4Ω:
2 x 300 Watt rms
Power output stereo 8Ω:
2 x 180 Watt rms
Power output bridged 8Ω:
600 Watt rms
Frequency Response:
20 Hz ÷ 20 kHz
Signal/noise rate:
> 105 dB
Crosstalk:
> 70 dB
Distortion (THD+N):
Intermodulation:
Damping factor:
200:1 (8 Ω)
Slew rate:
50 V/μS
INPUT SECTION
Input connector:
2 x XLR balanced, 6,3mm jack unbalanced
Input sensitivity:
0 / 0.775 dBm/V RMS
Input impedance:
10.000 kΩ
Controls:
Volume control for each channel
OUTPUT SECTION
Output connector:
2 x Neutrik Speakon 4 ways
SYSTEM PARAMETERS
Cooling:
Two-speed fan
Protections:
Temperature, DC, RFI short circuit, Soft-Start thermal on transformer
Amplifier class:
H
POWER REQUIREMENT
Operating voltage:
220÷240 / 110÷120 ~ 50 / 60 V ~ Hz
Max.current:
6 A
Power Consumption:
1300 W
PHYSICAL SPECIFICATIONS
Height:
88 / 3.46 mm/inch
Width:
483 / 19.01 mm/inch
Depth:
350 / 13.77 mm/inch
Net Weight:
11.45 / 25.24 Kg/Lbs
SHIPPING INFORMATION
Package height:
120 / 4.72 mm/inch
Package width:
540 / 21.25 mm/inch
Package depth:
470 / 18.05 mm/inch
Shipping Weight:
13.81 / 30.44 Kg/Lbs
Solid DYNACORD technology for fixed installations at very competitive prices. DSA power amplifiers offer a very high, stable output with high efficiency at a high performance level and are therefore the ideal choice for typical fixed installation applications. The connectivity consequently provides Phoenix type in/outs, the input level controls are located on the rear panel, also a switchable high-pass filter (50 Hz, 18 dB/oct) and a Ground Lift switch. The POWER REMOTE connector makes the task of remote controlling the power amplifier as well as switching it on and off simple. For further remote-supervision and –control possibilities and integration into IRIS-Net networks, an optional remote control module (RCM-810) is available.
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
.<br>
<br>
XLR inputs for patching in signals as well as Speakon ports for connecting speaker systems are provided for the maximum flexibility.<br>
A forced air cooling system maintains a low operating temperature.
</p>
<table><tbody><tr><th>Features</th> </tr><tr><td>Fast response and low distortion</td></tr><tr><td>Easy to configure in stereo / mono / bridge modes</td></tr><tr><td>Extensive protective circuits ensure high reliability and operating safety</td></tr><tr><td>Front panel signal / clip / protect LED indicators</td></tr><tr><td>Minimum load impedance (stereo / mono): 4 Ohm</td></tr><tr><td>XLR input connectors</td></tr><tr><td>SPEAKON output connectors</td></tr><tr><td>Switchable limiter</td></tr><tr><td>
<p>
2 unit 19 "acrobat_reader_logo."){kind=logo}
Reviews
There are no reviews yet.