Content |
Designed primarily for gaming, the GSX 1000 audio amplifier features a Sennheiser Binaural Rendering Engine. The groundbreaking 7.1 Virtual Surround Algorithm was developed with the needs of professional gamers in mind. Experience surround sound on a new level.
The stylish and durable GSX 1000 features an intuitive LED touch panel and aluminum volume ring for rapid fingertip control of your sound, and requires no additional drivers – so thereʼs no need to tab out of the game to tweak your settings. You also have the possibility to save up to 4 favorite settings.It works with PC and Mac. |
The PHDA02 - a reference class headphone amplifier with Stereo, Mono, and Dual Mono operation modes.
In Stereo mode, the L/R input signal is fed to the left and right earphones while the volume level is set by the Stereo/Left control. The front panel inputs provide simultaneous connection of two headphones in parallel. In Mono mode, the left and right channels are summed, and the resulting mono signal is fed to both the left and right earphones. Again, volume is governed by the Stereo/Left control. In Dual Mono mode, the left and right channels can be used independently with individual level controls for the left and right earphones.
The PHDA02 operates with all headphones with an impedance of 8 up to 200 Ohms. Impedance matching is achieved by a specially designed switchable transformer. Uncommon and costly, this solution provides superior performance, dynamic range, and signal-to-noise ratio at all loads.
Combo input sockets allow for balanced XLR and unbalanced TS headphone connection while parallel XLR outputs facilitate daisy chaining multiple units. The integrated power supply operates with mains from 100 VAC to 240 VAC.
The PHDA02 is equipped with low-noise op amps, and the output amplifiers' discrete power transistors are mounted on heatsinks. Dimensions are 1 U 9.5“.
|
MyMONITOR - Personal Headphone Monitor Mixer Overview
Problem: A performer needs to hear him/herself through headphones exclusively or mixed
with the output of a mixer, CD player, tape deck, or other stereo line level source. Only the
mic signal, however, should be going to the main mixer.
Solution: Connect MyMONITOR between the mic and line source, and the mixer. The Mic
and line Monitor levels can then be adjusted for mix and volume through the headphones.
Only the mic signal will go to the board. And since MyMONITOR can be AC or battery powered,
the unit can be used on a large stage or wherever there is no AC outlet nearby. Dynamic or
condenser mics can be used since phantom power would come through the Mic Thru jack from
the mixer or other source.
MyMONITOR - Personal Headphone Monitor Mixer Specifications:
Signal To Noise Ratio 90dB
Gain 15dB (1/4 in), 50dB (XLR)
Maximum Input Level -20dB mic, 40dB Monitor
Output Impedance 10 ohms
Power Requirements 12V DC (Adapter included) or one 9V battery
Phantom Power ON/OFF switch
Power LED indicator
Dimensions 4.5x2.75x1.5 inches (112mm x 72mm x 40mm)
Weight 1.3lb (590g)
|
The amPlug Night Train perfectly simulates the high-gain sound of the compact VOX Night Train tube amp. Just as with the actual Night Train head, you can switch between the two preamp sounds. The BRIGHT position boosts the high-frequency range; the THICK position offers a chunkier, heavier sound. The emulated speaker cabinet circuit accurately recreates the sound of the Night Train amp being played through the matching V112NT single 12" Night Train speaker cabinet. As a finishing touch, amPlug Night Train share some of the cool looks of its namesake amplifier.
Specifications - Controls: Gain, Tone, Volume; STANDBY/ON/FX switch
- Terminals: PHONES Jack (stereo), AUX In Jack (stereo)
- Power supply: AAA batteries (x 2)
- Battery life: amPlug Night Train:
- With zinc-carbon batteries: approximately 9 hours
- With alkaline batteries: approximately 24 hours
- Dimensions (W x D x H): 86 x 80 x 31mm/3.39" x 3.15" x 1.22“
- Weight: 40 g/1.41 oz. (not including batteries)
- Included items: AAA batteries (X2) (for verifying operation)
|
Specifications
General
Frequency response
20 Hz - 20 kHz (+0 dB, -1.5 dB)
Signal-to-noise ratio
100 dB (IHF A-weighted, input level control min.)
Channel separation
80 dB between adjacent channels
Line input
Front: 6.3 mm jacks, unbalanced
Rear: RCA connectors, unbalanced
Input impedance
40 kOhm
Nominal level
-10 dBV (0.3 V)
Headphone outputs
four 6.3 mm stereo jacks
Maximum output power
2 x 1.5 W at 8 Ohm (1 channel in use)
2 x 1,2 W an 8 Ohm (four channels in use)
Power supply
230 V AC, 50 Hz
Power consumption
10 W
Dimensions (W x H x D)
482 mm x 44 mm x 196 mm
Weight
4 kg | LDHPA6 6-Channel Rackmount Headphone Amplifier
The LD Systems HPA 6 is a highly flexible 1U 19" rack format headphone amplifier with 6 fully independent channels and comprehensive features for a wide range of professional audio monitoring applications.
Each channel provides a 6.3 mm TRS headphone output on the front panel with level control, mono/stereo switching, discrete left/right muting and a 6.3 mm TRS Aux input with Main/Aux balance control for mixing in further signal sources. Four-segment LED meters permit visual output level monitoring, and two 6.3 mm TRS outputs per channel on the rear allow for connecting a total of 18 headphones.
The HPA 6\'s main section features a master level control with eight-segment LED metering and 6.3 mm TRS input to mix in an additional source with all channels. The rear panel provides the main stereo inputs on balanced XLR and 6.3 mm TRS connectors and stereo outputs for daisy chaining multiple units.
- Type: 6-channel
- Inputs: Main Input (Stereo), Direct In (Stereo), 6 x Aux In (Stereo)
- Input Connections: XLR and 6.3 mm jack L&R (Main Input, balanced), 6.3 mm stereo jack (Direct In), 6.3 mm stereo jack (Aux In)
- Input Impedance: 13 kOhm
- Line Outputs: Main Output (stereo, balanced)
- Line Output Connectors: XLR and 6.3 mm jack L&R
- Headphone Outputs: 6 x 3
- Headphone Output Connectors: 6.3 mm stereo jack
- Power Output: 6 x 125 mW
- Minimal Connected Impedance per Channel: 8 ohms
- Frequency Response: 20 Hz - 20.000 Hz
- Controls: Main Input Level, 6 x Input Mix Main/Aux, 6 x Headphone Level, 6 x Mono Switch, 6 x Mute L&R, Power
- Indicators: Main Input/Direct In Level Meter (8-segment LED chain), 6 x channel level meter (4-segment LED chain), 6 x mono LED, 6 x Mute L&R LEDs, Power LED
- Power Supply: IEC power socket
- Operating Voltage: 220 - 240 V AC, 50 - 60 Hz / 110 - 120 V AC, 50 - 60 Hz
- Power Consumption: 40 W
- Cabinet Material: metal
- Cabinet Surface: painted
- Width: 483 mm
- Height: 44 mm
- Depth: 217 mm
- Accessories (included): power cord
|
Reviews
There are no reviews yet.