SENNHEISER E-912 HALF-CARDIOID CONDESER BOUNDARY MICROPHONE

The e 912 is a pre-polarized condenser boundary microphone with
half-cardioid pick-up pattern. Its acoustic properties have been
optimized for instruments, vocals and speech. The e 912 is an ideal
choice for pianos, theatre and opera productions, conference applications,
altars and lecterns.To optimally match the installation environment,
the e 912 is available in black or creme white.

Features
Frequency response and sensitivity optimized for picking up instruments,
vocals and speech
Unobtrusive, flat housing
Extremely rugged and step-resistant
Shock-absorbing rubber base
Mounting slots for table installation
Gold-plated XLR connector
Integrated pre-amp 
Delivery Includes
e 912 Microphone
Pouch
User manual

Technical Data
Transducer principle (Microphone)  permanently polarized condenser 
Pick-up pattern  half-cardioid 
Sensitivity in free field, no load (1kHz)  10 mV/Pa 
Max. Sound pressure level (aktiv)  135,6 dB 
Equivalent noise level  26 dB(A) 
Phantom powering  48 V / 1,1 mA 
Nominal impedance  Min. terminating impedance  1000 Ohm 
Dimensions  126,5 x 105 x 26,5 mm 
Weight  ca. 550 g 
 

The white-finished version of the U851R, the phantom-powered U851RW features a PivotPoint® rotating output connector, UniSteep® filter and UniGuard® RFI-shielding technology. Offering outstanding speech intelligibility and transparent sound quality for surface-mount applications, the U851RW accepts interchangeable condenser elements - available for boundary microphones in cardioid, hypercardioid and omnidirectional polar patterns. With a heavy die-cast case and silicon foam bottom pads to minimize coupling of surface vibration to the microphone, the U851RW is equipped with self-contained electronics, eliminating the need for an external power module.

• Designed for surface-mount applications such as high-quality sound reinforcement, professional recording, television, conferencing and other demanding sound pickup situations
• PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
• Superior off-axis rejection for maximum gain before feedback
• UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
• Self-contained electronics eliminate need for external power module
• Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
• Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
• Low-profile design with low-reflectance finish for minimum visibility
• Available in two colors: black (U851R) and white (U851RW)

• Element: Fixed-charge back plate, permanently polarized condenser
• Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
• Frequency Response: 30-20,000 Hz
• Low Frequency Roll Off: 80 Hz, 18 dB/octave
• Open Circuit Sensitivity: 34 dB (19.9 mV) re 1V at 1 Pa
• Impedance: 200 ohms
• Maximum Input Sound Level: 134 dB SPL, 1 kHz at 1% T.H.D.
• Dynamic Range: 108 dB, 1 kHz at Max SPL
• Signal to Noise Ratio: 68 dB, 1 kHz at 1 Pa
• Phantom Power Requiremens: 11-52V DC, 4 mA typical
• Switch: Flat, roll-off
• Weight: 9.2 oz (262 g)
• Dimensions: 4.25" (108.0 mm) long, 3.31" (84.0 mm) maximum width, 0.91" (23.0 mm) height
• Output Connector: TB3M-type
• Cable: 25.0' (7.6 m) long, 0.13" (3.2 mm) diameter, 2-conductor, shielded cable with TA3F and XLRM-type connectors

Designed to deliver easy, flexible control in conference and boardroom installations, the versatile U891Rx cardioid condenser boundary microphone features a touch-sensitive on-off switch that can be set to three modes: press-on/press-off, press to talk, and press to mute. The phantom-powered microphone is equipped with a unique PivotPoint® rotating output connector and an LED status indicator. UniGuard® innovations offer unsurpassed immunity from radio frequency interference; interchangeable elements are available in cardioid, hypercardioid and omnidirectional polar patterns; an 80 Hz low-cut UniSteep® filter reduces pickup of low-frequency ambient noise. The microphone's heavy die-cast case and silicon foam bottom pads minimize coupling of surface vibration to the microphone. The unit's self-contained electronics eliminate the need for an external power module.

• Designed for surface-mount applications such as high-quality sound reinforcement, professional recording, television, conferencing and other demanding sound pickup situations
• Ultra-quiet electronic switch can be set to any of three operating modes: "touch-on/ touch-off," "touch-to-talk" and "touch-to-mute“
• PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
• Superior off-axis rejection for maximum gain before feedback
• UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
• Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
• Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
• Low-profile design with low-reflectance finish for minimum visibility
• Available in two colors: black (U891Rx) and white (U891RWx)

• Element: Fixed-charge back plate, permanently polarized condenser
• Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
• Frequency Response: 30-20,000 Hz
• Low Frequency Roll Off: 80 Hz, 18 dB/octave
• Open Circuit Sensitivity: 34 dB (19.9 mV) re 1V at 1 Pa
• Impedance: 200 ohms
• Maximum Input Sound Level: 130 dB SPL, 1 kHz at 1% T.H.D.
• Dynamic Range: 104 dB, 1 kHz at Max SPL
• Signal to Noise Ratio: 68 dB, 1 kHz at 1 Pa
• Phantom Power Requirements: 11-52V DC, 4 mA typical
• Weight: 264 g
• Dimensions: 108.0 mm long, 84.0 mm maximum width, 23.0 mm height
• Output Connector: TB3M-type
• Cable: 7.6 m long, 3.2 mm diameter, 2-conductor, shielded cable with TA3F and XLRM-type connectors

    Designed for Broadcast, House of Worship, Pro Music, and other applications.
    Half-cardioid polar pattern
    Boundary layer
    Ultra-thin profile (16 mm) housing
    Rubber non-slip bottom pad and strong steel screen
    Integrated pop filter

Case Material    Die cast zinc
Connector Type    3-pin XLR
Element    Back Electret Condenser
Finish    Non-reflecting Black
Finish    White
Impedance, Low-Z balanced    200 Ω
Mic Type    Boundary
Open Circuit Voltage    25 mV/Pascal
Polar Pattern    Cardioid
Wired/Wireless    Wired
Height    16 mm (0.63“)
Width    94 mm (3.7“)
Depth    123 mm (4.84“)
Weight Net    12.63 oz (358 g)

A wide range condenser microphone with a cardioid polar pattern, the ultra-smart U891RCx is equipped with local or remote switching options. For flexible control in conference and boardroom installations, the unit's external contact closure ability allows a user to trigger an external device - a camera, for instance - from a switch on the microphone. Another ease-of-use feature: the microphone's electronic on-off switch can be set to three operating modes: touch-on/touch-off, press to talk, and press to mute. The mic is also equipped an 80 Hz low-cut UniSteep® filter to reduce pickup of low-frequency ambient noise. Its red LED status indicator can be controlled remotely. UniGuard® innovations offer unsurpassed immunity from radio frequency interference; interchangeable elements are available in cardioid, hypercardioid and omnidirectional polar patterns; a unique rotating PivotPoint® connector changes the cable exit point - no tools required. It requires 11 to 52V DC phantom power, which operates the microphone and switch circuitry.

• Designed for surface-mount applications such as high-quality sound reinforcement, conferencing, distance learning and other demanding sound pickup situations
• Ultra-quiet electronic switch can be set to any of three operating modes: "touch-on/touch-off," "touch-to-talk" and "touch-to-mute“
• External contact closure capability permits control of remote devices from microphone switch
• External LED control allows for accurate depiction of the live status of the microphone
• PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
• Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
• UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
• Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
• Low-profile design with low-reflectance black finish for minimum visibility

• Element: Fixed-charge back plate, permanently polarized condenser
• Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
• Frequency Response: 30-20,000 Hz
• Low Frequency Roll Off: 80 Hz, 18 dB/octave
• Open Circuit Sensitivity: 34 dB (19.9 mV) re 1V at 1 Pa
• Impedance: 200 ohms
• Maximum Input Sound Level: 130 dB SPL, 1 kHz at 1% T.H.D.
• Dynamic Range: 104 dB, 1 kHz at Max SPL
• Signal to Noise Ratio: 68 dB, 1 kHz at 1 Pa
• Phantom Power Requirements: 11-52V DC, 4 mA typical
• Weight: 266g
• Dimensions: 108.0mm long, 84.0mm maximum width, 23.0mm height
• Output Connector: TB5M-type
• Cable: 7.6m long, 3.2mm diameter, 5-conductor shielded cable (2 conductors under shield; 3 control wires outside shield); TA5F-type connector at microphone end, output end stripped and tinned for connection to electronic device