Content |
Small omni-directional clip-on microphone for speech and vocal applications.
Small omni-directional clip-on microphone for speech and vocal applications. High speech intelligibility. Easy attachment on clothing. Mini jack for bodypack transmitters from evolution wireless series.
This microphone is intended to be used with the Freeport, XSW, XSW-1, XSW2, AVX, SL, and EW-D1 series. It is however compatible with all the analogue or digital Sennheiser transmitters that accept a threaded 3 pole 3.5mm jack.
Dimensions: 10,5 mm diameter
Frequency response: 50-18000Hz
Transducer principle: Permanent polarized condenser
Connection cable: threaded mini-jack
Cable length: 1,6m
Pick-up pattern: omni-directional
Sensitivity in free field, no load (1kHz): 20 mV/Pa
Equivalent noise level: 36 dB
Maximum sound pressure level: 130 dB
Operating voltage (stand alone): 7,5 V
Τype: |
Lavalier |
Colour: |
Black |
Connector: |
Threaded Jack 3P 3.5 |
|
Shure WL-185 Lavalier Condenser Microphone
Models WL183, WL184 and WL185 are lavalier electret condenser mics designed for use
with a wireless body-pack transmitter. Each mic has a 1.2 meter (4 ft.) cable terminated
with a miniature 4-pin mini connector. Included tie clip can be rotated in 90 degree intervals for placement flexibility.
WL185 (Cardioid):
Recommended for general purpose sound reinforcement applications requiring good rejection of ambient noise.
Use of windscreen highly recommended. Pickup angle: 130 degrees.
Type
Condenser (electret bias)
Frequency Response
50 to 17,000 Hz
Output Impedance
1800 ohms
Sensitivity (1 Pa = 94 dB SPL)
WL183: -40.0 dBV/Pa
WL184: -44.5 dBV/Pa
WL185: -45.5 dBV/Pa
Maximum Sound Pressure Level
WL183: 125.0 dB SPL
WL184: 129.5 dB SPL
WL185: 130.5 dB SPL
Output Noise (A-weighted)
WL183: 22.5 dB SPL
WL184: 27.0 dB SPL
WL185: 28.0 dB SPL
Dynamic Range
102.5 dB
Polarity
Positive pressure on diaphragm produces positive voltage on pins 3 and 4 relative to pin 1.
Power Requirements
Regulated nominal +5 Vdc (1.5 Vdc to 10 Vdc) provided at microphone connector pin 2 relative to pin 1 of a Shure wireless microphone transmitter.
|
This miniature condenser microphone achieves full-sounding pickup and is known for outstanding consistency and dependable performance. Supplied with both a clothing clip and guitar mount, it provides natural and articulate vocal reproduction when used as a clip-on lavalier and excels in pickup of acoustic guitar. The PRO70 is designed to make music and speech clearly and comfortably audible, yet never draw attention to itself or its operation. The microphone is equipped with a low-frequency roll-off switch that allows for reduced pickup of room noise. The versatile PRO70 may be powered by either battery or phantom power. Its cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation of the desired sound source. Miniature condenser microphone is ideal for both vocal and acoustic guitar applications Natural and articulate vocal reproduction when used as a clip-on lavalier - clothing clip included Excels in pickup of acoustic guitar with included instrument adapter Cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation of desired sound source Switchable low-frequency roll-off Corrosion-resistant contacts from gold-plated XLRM-type connector Operates on battery or phantom power 6\' (1.8 m) cable permanently attached between microphone and power module Element: Fixed-charge back plate, permanently polarized condenser Polar Pattern: Cardioid Frequency Response: 100-14,000 Hz Low Frequency Roll Off: 80 Hz, 8 dB/octave Open Circuit Sensitivity: Phantom: -45 dB (5.6 mV) re 1V at 1 Pa Battery: -45 dB (5.6 mV) re 1V at 1 Pa Impedance: Phantom: 200 ohms Battery: 200 ohms Maximum Input Sound Level: Phantom: 123 dB SPL, 1 kHz at 1% T.H.D. Battery: 123 dB SPL, 1 kHz at 1% T.H.D. Dynamic Range: Phantom: 96 dB, 1 kHz at Max SPL Battery: 96 dB, 1 kHz at Max SPL Signal to Noise Ratio: 67 dB, 1 kHz at 1 Pa Phantom Power Requiremens: 11-52V DC, 2 mA typical Battery Type: 1.5V AA/UM3 Battery Current Life: 0.4 mA / 1200 hours typical (alkaline) Switch: Off, on-flat, on-roll-off Output Connector: Integral 3-pin XLRM-type Cable: Integral 6\' (1.8 m), permanently attached between microphone and power module Accessories: AT8411 clothing clip; AT8444 instrument adapter; power module; windscreen; battery; soft protective pouch |
Transducer Electret condenser
Polar Pattern Cardioid
Frequency Response 20 to 20,000Hz
Output Impedance 165.5 Ω
Sensitivity -39.0 dBV/Pa (11.0 mV)
Max Input Sound Level (SPL) 1000 Ω load: 129.5 dB SPL; 2500 Ω load: 134.5 dB SPL
Signal-to-Noise Ratio 57.0 dB
Dynamic Range @1kHz
1000 Ω: 92.5 dB SPL; 2500 Ω: 97.5 dB SPL
Self Noise 37.0 dB
(equivalent SPL, A-weighted, typical)
Clipping Level 1000 Ω load: 1.0 dBv; 2500 Ω load: -4.5 dBv
Operating Temperature Operating: 0 to 135°F (-18 to 57°C)
Storage: -20 to 165°F (-29 to 74°C)
Polarity XLR: Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3
Power Requirements 11-52VDC phantom power (IEC-61938),
Dimensions (LxDiameter) Length: 5' (1.52m)
Diameter: 0.23" (5.8mm)
Weight 4.3 oz (121 g)
|
All models include foam windscreen, swiveling lapel clip, dual tie clip, pin mount, magnet mount
Subminiature size (5.8 mm diameter x 11 mm height)
Electret condenser cartridge
Unidirectional pattern
One termination: 4-pin mini connector (fits directly into Shure wireless transmitters)
High Boost equalization caps included for optimal clarity and response
Provides a 10 dB boost centered at 12 kHz
Used in applications that require a chest-worn microphone
Black and white models available
All models include magnet mount, lapel clip, dual tie clip, pin mount, and two foam windscreens and carry case
requency response: 20-20,000 Hz
Low visibility with a variety of options for mounting
Low handling noise
Legendary Shure quality, ruggedness, and reliability
|
Shure cable with base WL180N fits with R183/184/185 |
Reviews
There are no reviews yet.