| Content |
The e 608 is a super-cardioid microphone ideal for almost invisible clip-miking
of woodwind (except certain Flutes), brass and drums. A newly developed clamp
and gooseneck mounting enables the capsule to be positioned close to the signal
source for high realism and high-level output.
Features
Rugged reinforced glass-fibre body
Shock-mounted capsule provides low sensitivity to impact and handling noise
Hum compensating coil
Extremely robust connection cable with XLR connector
Delivery Includes
1 e 608
1 microphone clip
1 pouch
Technical Data
Frequency Response 40.....16000 Hz
Sensitivity in free field, no load (1kHz) 0,8 mV/Pa
Min. terminating impedance 1000 Ohm
Dimensions d 17 x 185 mm
Weight w/o cable 20 g
|
This miniature condenser microphone achieves full-sounding pickup and is known for outstanding consistency and dependable performance. Supplied with both a clothing clip and guitar mount, it provides natural and articulate vocal reproduction when used as a clip-on lavalier and excels in pickup of acoustic guitar. The PRO70 is designed to make music and speech clearly and comfortably audible, yet never draw attention to itself or its operation. The microphone is equipped with a low-frequency roll-off switch that allows for reduced pickup of room noise. The versatile PRO70 may be powered by either battery or phantom power. Its cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation of the desired sound source.
Miniature condenser microphone is ideal for both vocal and acoustic guitar applications
Natural and articulate vocal reproduction when used as a clip-on lavalier - clothing clip included
Excels in pickup of acoustic guitar with included instrument adapter
Cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation of desired sound source
Switchable low-frequency roll-off
Corrosion-resistant contacts from gold-plated XLRM-type connector
Operates on battery or phantom power
6\' (1.8 m) cable permanently attached between microphone and power module
Element: Fixed-charge back plate, permanently polarized condenser
Polar Pattern: Cardioid
Frequency Response: 100-14,000 Hz
Low Frequency Roll Off: 80 Hz, 8 dB/octave
Open Circuit Sensitivity: Phantom: -45 dB (5.6 mV) re 1V at 1 Pa Battery: -45 dB (5.6 mV) re 1V at 1 Pa
Impedance: Phantom: 200 ohms Battery: 200 ohms
Maximum Input Sound Level: Phantom: 123 dB SPL, 1 kHz at 1% T.H.D. Battery: 123 dB SPL, 1 kHz at 1% T.H.D.
Dynamic Range: Phantom: 96 dB, 1 kHz at Max SPL Battery: 96 dB, 1 kHz at Max SPL
Signal to Noise Ratio: 67 dB, 1 kHz at 1 Pa
Phantom Power Requiremens: 11-52V DC, 2 mA typical
Battery Type: 1.5V AA/UM3
Battery Current Life: 0.4 mA / 1200 hours typical (alkaline)
Switch: Off, on-flat, on-roll-off
Output Connector: Integral 3-pin XLRM-type
Cable: Integral 6\' (1.8 m), permanently attached between microphone and power module
Accessories: AT8411 clothing clip; AT8444 instrument adapter; power module; windscreen; battery; soft protective pouch |
All models include foam windscreens, swiveling lapel clip, dual tie clip, magnet mount, and mini mount
Subminiature size (5.8 mm diameter x 11 mm height)
Electret condenser cartridge
Omnidirectional pattern
One termination: 4-pin mini connector (fits directly into Shure wireless transmitters)
Two sensitivities available:
--Standard: -40 dBV/Pa (for speech applications)
--Reduced: -50 dBV/Pa (10 dB more headroom for theater applications)
Interchangeable equalization caps for optimal clarity and response:
--Silver mesh cap provides a 4 dB boost in the 8-18 kHz range - typically used in applications that require a microphone to be head-mounted
--Gold mesh cap provides a 10 dB boost centered at 12 kHz - typically used in applications that require a chest-worn microphone
Black, beige, and white models are available
All models include magnet mount, lapel clip, dual tie clip, pin mount, and two foam windscreens
Frequency response: 20-20,000 Hz
|
Shure WL-185 Lavalier Condenser Microphone
Models WL183, WL184 and WL185 are lavalier electret condenser mics designed for use
with a wireless body-pack transmitter. Each mic has a 1.2 meter (4 ft.) cable terminated
with a miniature 4-pin mini connector. Included tie clip can be rotated in 90 degree intervals for placement flexibility.
WL185 (Cardioid):
Recommended for general purpose sound reinforcement applications requiring good rejection of ambient noise.
Use of windscreen highly recommended. Pickup angle: 130 degrees.
Type
Condenser (electret bias)
Frequency Response
50 to 17,000 Hz
Output Impedance
1800 ohms
Sensitivity (1 Pa = 94 dB SPL)
WL183: -40.0 dBV/Pa
WL184: -44.5 dBV/Pa
WL185: -45.5 dBV/Pa
Maximum Sound Pressure Level
WL183: 125.0 dB SPL
WL184: 129.5 dB SPL
WL185: 130.5 dB SPL
Output Noise (A-weighted)
WL183: 22.5 dB SPL
WL184: 27.0 dB SPL
WL185: 28.0 dB SPL
Dynamic Range
102.5 dB
Polarity
Positive pressure on diaphragm produces positive voltage on pins 3 and 4 relative to pin 1.
Power Requirements
Regulated nominal +5 Vdc (1.5 Vdc to 10 Vdc) provided at microphone connector pin 2 relative to pin 1 of a Shure wireless microphone transmitter.
|
Shure cable with base WL180N fits with R183/184/185 |
All models include foam windscreen, swiveling lapel clip, dual tie clip, pin mount, magnet mount
Subminiature size (5.8 mm diameter x 11 mm height)
Electret condenser cartridge
Unidirectional pattern
One termination: 4-pin mini connector (fits directly into Shure wireless transmitters)
High Boost equalization caps included for optimal clarity and response
Provides a 10 dB boost centered at 12 kHz
Used in applications that require a chest-worn microphone
Black and white models available
All models include magnet mount, lapel clip, dual tie clip, pin mount, and two foam windscreens and carry case
requency response: 20-20,000 Hz
Low visibility with a variety of options for mounting
Low handling noise
Legendary Shure quality, ruggedness, and reliability
|
Reviews
There are no reviews yet.