| Content |
The Showtec CO2 Q-Lock system is a complete range of products to create a fast and safe way to build all kinds of CO2 setups. It can be applied for both rental and fixed installations. The Q-Lock products are all are equipped with male and female quick lock couplers. They have back pressure valves to guarantee a closed and save system at all times . The CO2 Q-Lock range consists of hoses, splitters, combiners, a distributor and various adapters. With the splitters and the combiners it is possible to integrate multiple shooters, FX Ice Jets or multiple bottles in one system. The adapters are used on the Showtec CO2 Ice Gun, FX Ice Jets or hoses with thread to upgrade them to all Q-Lock applications.
Note: If you use Q-Lock products always make sure that your Ice Guns and Ice Jets are prepared with CO2 3/8 Q-Lock female adapters.
Quick and safe connection
Closed system
Saves CO2 Gas
Combine multiple bottles and hoses in one closed setup
Specifications
Max pressure: 175 bar / 2537 psi
Safety ratio: 1:4
Inner shell material: Polyester
Outer shell material: Polyurethane
Internal diameter: 9,7mm
External diameter: 16,0mm
Min. Bend radius: 60mm
Input: male QLock
Output: female QLock
Length: 10m
Weight G/m: 155gr
These hoses meet/exceed standard SAEJ517 sec. SAE100R7 - EN 855 - ISO 3949 |
FULL-BRIDGE PWM MOTOR DRIVER
The L6219 is a bipolar monolithic integrated circuits intended to control and drive both winding of a bipolar stepper motor or bidirectionally control two DC motors.
The L6219 with a few external components form a complete control and drive circuit for LS-TTL or microprocessor controlled stepper motor system. The power stage is a dual full bridge capable of sustaining 46V and including four diodes for current recirculation.
A cross conduction protection is provided to avoid simultaneous cross conduction during switching current direction.
An internal pulse-width-modulation (PWM) controls the output current to 750 mA with peak startup current up to 1 A.
Wide range of current control from 750 mA (each bridge) is permitted by means of two logic inputs and an external voltage reference. A phase input to each bridge determines the load current direction. A thermal protection circuitry disables the outputs if the chip temperature exceeds safe operating limits.
*ABLE TO DRIVE BOTH WINDINGS OF BIPOLAR STEPER MOTOR *OUTPUT CURRENT UP TO 750mA EACH WINDING *WIDE VOLTAGE RANGE 10V TO 46V *HALF-STEP, FULL-STEP AND MICROSTEPPING MODE *BUILT-IN PROTECTION DIODES *INTERNAL PWM CURRENT CONTROL *LOW OUTPUT SATURA TION VOLTAGE *DESIGNED FOR UNSTABILIZED MOTOR SUPPLY VOLTAGE *INTERNAL THERMAL SHUTDOWN
STEPPER MOTOR DRIVER, 6219, DIP24; Motor Type:Stepper; No. of Outputs:4; Output Current:1A; Driver Case Style:DIP; No. of Pins:24; Operating Temperature Range:0°C to +70°C; SVHC:No SVHC (20-Jun-2011); Base Number:6219; Device Type:Motor; IC Generic Number:6219; IC Temperature Range:Commercial; Logic Function Number:6219; Operating Temperature Max:70°C; Operating Temperature Min:0°C; Output Current Max:0.75A; Package / Case:DIP; Supply Voltage Max:46V; Supply Voltage Min:10V; Termination Type:Through Hole
Key Features - Able to drive both windings of bipolar stepper motor
- Output current up to 750 mA each winding
- Wide voltage range: 10 V to 46 V
- Half-step, full-step and microstepping mode
- Built-in protection diodes
- Internal PWM current control
- Low output saturation voltage
- Designed for unstabilized motor supply voltage
- Internal thermal shutdown
|
Remote Control for Z-800 and Z-1000
|
The Detonator is an optional, dedicated remote control tool for easy command of the Atomic strobe's flash rate and intensity. It includes "blinder effect” and "single flash” detonator buttons as well as a chase/synchronization toggle switch. Easy to set up and operate, the Atomic Detonator requires no external power source.
* Dedicated remote control for Atomic strobe series
* Fader-controlled flash rate and intensity
* Single button for Detonator blinder effect
* Separate button for single flash and flash sync
* Chase effect operation with multiple units
* No external power necessary
* Easy set-up and operation
| The Artex harness AX60 S ( Article 1062) in accordance with EN 361 / EN 358 has length adjustable shoulder , leg straps and is equipped with a back header plate m . Anchorage in the shoulder area , 2 catch loops in the chest area and a wide, padded backrest equipped . The safety harness AX 60 S is available in this variant with fall arrest on tether . The Auffangurt AX 60 S is suitable for collecting , abseiling , holding , climbing and rescue .
SK 12-Y Verbindungsmittel mit Bandfalldämpfer
Der Artex Auffanggurt AX60 S (Artikel 1062) nach EN 361 / EN 358 hat längeneinstellbare Schulter-, Beingurte und ist mit einer Rückenverteilerplatte m. Auffangöse im Schulterbereich, 2 Auffangschlaufen im Brustbereich und einer breiten, gepolsterten Rückenstütze ausgestattet. Den Auffanggurt AX 60 S gibt es in dieser Variante mit Steigschutzöse am Haltegurt. Der Auffangurt AX 60 S eignet sich zum Auffangen, Abseilen, Halten, Steigen und Retten.
Artikeldetails
Rückenverteilerplatte m. Auffangöse im Schulterbereich
Gurtverschluss im Brustbereich
vordere Auffangschlaufen i. Brustbereich
Schulter- und Beingurte längeneinstellbar
Durchsteckverschluss (Schnellverschluss) an den Beingurten u. Haltegurt
Haltegurt / Leibgurt m. seitl. Halteösen
breite, gepolsterte Rückenstütze
Steigschutzöse am Haltegurt
Sitzgurt
Gewicht: 1,6kg
Farbe: orange / blau |
- 6-way power strip with plastic housing
- Sockets are 45° rotated
- Surge protection
- With illuminated 2-pole rocker switch
- Colour: white
|
Reviews
There are no reviews yet.