Content |
Want to make sure that your trussing is aligned? Want to know the height of the venue? Want to know the volume of the room? No problem! Know it in a few moments with this Ultrasonic Distance Meter!
• Calculates area and volume • Laser to target the point from where you want to measure • Auto converts feet to meters • Backlight
Specifications
Measurement range: 0,6 to 15 m Accuracy: ± 0,5% ± 1 Digit Resolutions: 0,01 m Aperture angle: ±5° Power supply: 6F22(9V) x 1 Dimensions: 136 x 59 x 38 mm Weight: approx. 150 g (incl. battery)
|
The MiniSPL is the perfect accessory to the Acoustilyzer & Minilyzer for
acoustical measurements.
The MiniSPL is a battery powered measurement microphone. Together
with the Acoustilyzer or Minilyzer, it forms an acoustical analyzer and integrating
sound level meter. Additionally it may be operated as a stand-alone microphone
e.g. connected to a balanced audio-line, a microphone-input or a sound-card.
Product-details
? Battery powered
? Factory-set sensitivity
? No phantom power required
? 1/2" microphone, class 2 acc. IEC 61672
? Omni-directional
? Supplied with mic clamp, wind protection
? Typical frequency response included
MiniSPL together with Acoustilyzer:
? SPL Meter / RTA
? Reverberation Time RT60
? Delay Time
? FFT Analyzer
? Speech Intelligibility STI-PA
MiniSPL together with Minilyzer:
? Measurements: SPL, min./max., Leq
? 1/3rd octave spectrum analyzer |
Palmer Pro MCT DMX 3-pin and 5-pin DMX and XLR cable tester
MCT DMX
This cable tester checks 3-pin and 5-pin DMX cables for continuity in fully automatic or manual pin selection modes. Pin connection status of the male and female cable ends is indicated by two rows of bright LEDs. In addition, the unitʼs 3-pin connectors can also be used to test XLR microphone cables. The DMX Cable Tester comes with two L-brackets for variable mounting options.
- Tests 3-pin and 5-pin DMX cables for continuity
- Also tests 3-pin XLR microphone cables
- Automatic test mode or manual pin 1 - 5 selection
- LED indicators
- Mounting brackets included
Product type
Test Equipment
Connectors
XLR (3-pin) , XLR (5-pin)
Controls
Auto Scan , On / Off , Scan switch
Indicators
LED chain
Operating voltage
2 x AA battery
Acoustic continuity test
no
Test cable
no
Cabinet material
sheet steel
Cabinet surface
powder coated
Width
240.2 mm
Height
48 mm
Depth
53 mm
Weight
0,7 kg
|
Model Number |
JZK-601 |
Memory groups |
32*2 groups |
Product Dimensions |
14.3* 9.3* 3.8 CM |
Business type |
Manufacturer |
Storage temperature |
-20-50°C |
Storage Humidity |
15%-90%RH |
Operating temperature |
5-40°C |
Operating Humidity |
40%-85%RH |
Display |
LCD crystal digital display |
Measuring method |
Infrared radiation temperature measurement |
Measurement range |
32~42.5℃ fro human body, 0-100℃ for objects |
Resolution |
0.1 degrees Celsius (0.1 degrees Fahrenheit) |
Accuracy |
0-39.9kpa(0-299 mmhg) |
Voltage |
3 V |
Power consumption |
|
|
Cable Tester ACT-100
The Alphaton active remote cable tester can be used for testing either normal short cables or long ones, especially mufticores, wkh connectors not being accessible at one time. The tester is especially suded for fixed installations where cables can not be tested with a standard type cable tester or Ohm meter. Either symmetric and unsymmetric cables can be tested. “Cold" solderings and junction resistances are displayed by color or luminosity changes in three color LED Display. The imprinted fault table incorporates alt important fault conditions, indeed not all possible ones due to their reiatively large number. In case the display is in a state which cannot be found on the imprinted table, it can be looked up in the user's manual. In any case, however, the cabie is in aquite unusable state and should be repaired or replaced.The Alphaton cable tester has a SEND and a REMOTE section. The REMOTE sectionconsistsof two recessed mounted XLR type male or female connector and a stereo phone jack at the right hand side of the tester. Additionally, a separate REMOTE plug is delivered togetherwith the active remote cable tester for testing long cables in fixed installations.
| GP-300 Infrared Thermometer is specially designed to take the body temperature of a person regardless of room temperature.
Features:
- Precise non-contact measurements
- User selectable ºC or ºF
- Selectable Body and Surface temp
- Set Alarm value for fever warning
- Access to multiple memory values up to 32 records
- Trigger lock
- Automatic Data Hold & Auto power off
- Automatic selection range and Display Resolution 0.1ºC (0.1ºF)
- Backlight LCD display
- Size 149 x 95 x 44 mm
- Weight 172g
- CE certified
Specifications
|
Reviews
There are no reviews yet.