| Content |
Powersplit 3 CEE 16A
4 x Schuko, 2 x CEE 16A 5p
Input power connector: CEE 16 A male 5 pole connector
Max. power load: 3 x 16A
Output power connector: 4 pcs Schuko, 2 pcs CEE 16A female 5 pole
IP-rate: IP-44
Cable length: 1,5 m
Weight: 3,4 kg
|
Work ESD 10K Automatic Voltage Regulator
It is a voltage regulator able to keep always constant the power supply in 220V
(or 110 V in the additional connector) when the voltage oscillates in a margin
from 140 to 250V ( 220 V input) or 60 to 130 V (110 V input) and connected to
a fix load of 10.000W. The need to keep a stable main voltage, above all for
systems or goods which performing depends on this value, it conserves these
regulators in an appreciated auxiliary device, when we have to supply mixers
effect appliances, etc. The incorporate 2 high brightness displays allow to read
clearly, working conditions, like input, output and main voltage. With the finality
to avoid parasite noise proceeding of the main switch, these units dispose of a
delay in the adjustable switching of 3 or 6 seconds, afterwards it runs in working
normal mode. In the protection section, both devices include protection against a
higher input voltage (255V), overheat and excess of output voltage. In these cases
the unit will switch off, transmitting an acoustic signal and a message in the display.
It disposes of a precise switch in the output voltage which allows to adjust this
parameter from a 1% to 3%.In the front panel, this unit disposes of a 63 A circuit breaker.
In the rear side are placed input/output connection CEE 32 A 3 pole. 1 additional
schucko output for 220 V and another for 110 V.
This unit is cooled by fan.
Technical Specifications:
Power supply: 140V- 250V AC.
Maximum joint load: 10000 VA.
Delay, selectable: 3 or 6 seconds .
Precision of output tension, selectable: 1% - 3%
Protections against:
Excessive temperature of 95 C
High input level
Overload
Dimensions: 460x305 x 260 mm
| PSA-631
With Ampere Meter
Bring safety on stage! Power is the most important chain for a successful show on any stage. Showtec developed together with leading rental companies the power distributors that will keep your power and equipment save. The PSA-631 gives you real-time voltage and amperage information during your show. Now you can monitor your setup and make sure that the power is correctly distributed at all times.
SpecificationsFront:
• Digital voltage & amperage-monitoring
per Phase.
• Residual current circuitbreaker
FI 63A 4 pol. 0,03A
• 4 x 32A ʽC' automatic fuses.
Back:
• Input: 1,5 m (5 wires) cable with
CEE-socket 3 x 63A
• Output: 4 pcs. CEE 3 x 32A socket
Dimensions: 19" rackmount/3U
Weight: 9,5 kg |
Electrical Specifications and Connections
Rated Current (A) 16 A
Flashover Voltage 250 V
Pins 3
Minimum Wire Size 0.75 mm²
Maximum Wire Size 1.5 mm²
Mechanical Specifications
Length (mm) 50 mm
Height (mm) 65 mm
Width (mm) 5 mm
Mounting Size 50 x 50 mm
Weight 0.06 kg
IP Rating IP44
Housing Plastic
Colour Blue
Product Properties
Pin Connection Screw Terminal
Contact Type Brass
| 1 schucko cable input 6 schucko outputs |
This is a 32 A three-phase power splitter with 3x 32A/400V input and 6 Schuko 16A/250V output.
Each Schuko is protected by a 16A circuit breaker and each phase can be read out by a 4-digit
voltmeter as well as 4-digit ammeter. Furthermore, a residual current circuit breacker is used for
protection against electronic shock under fault conditions. Also, a CEE-socket is provided for plugging
in power.
|
Reviews
There are no reviews yet.