SHURE MX153 /O Condenser Omni Headset Microphone

ansducer Type
Electret condenser

Polar Pattern
Omnidirectional

Frequency Response
20 to 20,000 Hz

Output Impedance
N / A

Sensitivity (open circuit voltage, @ 1 kHz, typical)
-41 dBV/Pa (9 mV)

Maximum SPL (1 kHz at 1% THD)
2500 Ω load: 107 dB SPL
1000 Ω load: 107 dB SPL

Signal-To-Noise Ratio
60 dB

Dynamic Range @ 1 kHz
2500 Ω load: 73 dB
1000 Ω load: 73 dB

Self-Noise (equivalent SPL, A-weighted, typical)
34 dB

Operating Temperature Range
-18°C (0°F) to 57°C (135°F)

Polarity
Positive pressure on diaphragm produces negative voltage on pin 3 with respect to pin 1

Power Requirements
+5 V DC (130 μA minimum)

Weight
19.76 g

Shure WCM16 Headworn Condenser Microphone

The Shure Model WCM16 headworn electret condenser microphone is intended for wireless use by
performers, lecturers, and others who require the highest quality voice pickup with maximum mobility.
Its wide frequency response, low RF susceptibility and reliable operation at temperature and humidity
extremes make the WCM16 suitable for virtually any vocal application. When used with the Shure bodypack
transmitters, the performance of the WCM16 closely resembles the finest conventional vocal microphones.

 Miniaturized active circuitry included in the cartridge assembly provides equalization that tailors the low-frequency
response to resemble the warmproximity effect of larger vocal microphones. Because of this low-end response, it
is not necessary to position the microphone directly in front of the mouth, thus avoiding much popping and breath
noise, even without the supplied foam pop screen.

 The microphone's hypercardioid unidirectional pickup pattern provides maximum isolation from ambient noise and
from adjacent sound sources such as musical instruments, loudspeakers and other performers. This permits higher
gain-before-feedback without loss or masking of vocals.

Features:

Extra lightweight, adjustable headband stays secure and virtually disappears while being worn
Response comparable to finest conventional vocal microphones
Hypercardioid polar pattern provides maximum isolation from vocalist's own instrument and those of other performers
Uniform polar pattern at all frequencies for maximum gain before feedback
High input clipping level eliminates overload distortion
Cable terminates as 4-pin mini connector
Supplied acoustic foam pop screen
Reliable at temperature and humidity extremes

Specifications:

Frequency Response
50 to 18,000 Hz
Polar Pattern
Hypercardioid, uniform with frequency
Output Impedance
1200 ohms
Output Level (close-talked at 1,000 Hz)
Open Circuit Voltage -55.0 dbV (1.8 mV) at 0.6 m
1 Pascal=94 db SPL
Maximum Sound Pressure Level
150 dB at 1% THD
Dynamic Range
121 dB
Output Noise
29 dB equivalent SPL, A-weighted
Signal-to-Noise Ratio
65 dB at 94 dB SPL
Polarity
Microphone: Positive sound pressure on diaphragm produces positive voltage on pins 3 and 4 with respect to pin 1 (ground) of microphone output connector
Receiver-- 1/4" Phone Jack Output: Positive sound pressure on diaphragm produces positive voltage on tip of receiver 1/4" output connector
Receiver-- XLR Output: Positive sound pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3 of the XLR output connector
Current Drain
0.35 mA
Recommended Operating Voltage
+5 Vdc (positive on pin 2, negative on pin 1)
Environmental Conditions
Operating Temperatures: -18 to 60 degrees C (0 to 140 degrees F)
Storage Temperatures: -29 to 66 degrees C (-20 to 150 degrees F)
Humidity: 0 to 95%
Cable
1.5m (5 ft), small-diameter, shielded, with 4-pin mini connector
Case Finish (Microphone and Headband)
Matte black enamel
Net Weight
36 g (1.27 oz)

• Excellent feedback rejection
• Microphone includes a detachable cap as integral wind/popshield
• Individually adjustable to all head sizes
• Neckband design keeps the microphone clear from shirt-collar or clothing
• Twist-proof microphone boom (Ø 2.0 mm), can be attached to the left or right side
• Microphone boom is adjustable in length and angle
• Flexible gooseneck section
• Connection cable can easily be interchanged
• All metal parts coated in a physical vapour deposition process
• Can also be used with the omni-directional HSP 2 boom microphone

• Boom microphone
• Neckband
• Connection cable
• Plastic transport case, foam-lined with cut-outs
• Operating instructions

• Pick-up pattern  cardioid
• Frequency response  40...20 000 Hz
• Nominal impedance  (@ 1 kHz) 1000 Ohm
• Min. terminating impedance  4700 Ohm
• Sensitivity in free field, no load (1kHz)  4 mV/Pa
• Maximum sound pressure level (passiv)  150 dB
• Equivalent noise level  37 dB(A)
• Current consumption  ca. 250 µA
• Operating voltage (stand alone)  4,5-15 V
• Cable length  1,6 m
• Diameter  microphone head 8,4 mm
• Diameter  boomarm 2,4 mm
• Weight  9,2 g (without cable)

High-quality permanently polarized condenser headmic with omni-directional pick-up pattern

High-quality permanently polarized condenser headmic with omni-directional pick-up pattern

Shure WBH53T Tan Headworn Condenser Microphone

Features of the Shure WBH53 Headworn Microphone:

? Comfortable, latex-free Dynaflex? earforms that hide behind the ears
? Thin, non-reflective wireframe that is easily hidden underneath hair
? Ultra-thin detachable microphone boom mount for right or left positioning
? Interchangeable frequency response caps (mild or high, two pieces each)
? Two foam windscreens included
? Clothing clip for securing cable
? Corrosion resistant
? Easy to clean
? Durable carrying case for protective storage
? Available in either black or tan
? Available with either TA4F connectors or tinned leads (no connector) for full wireless system compatibility