Content |
Shure MX202B-C Microflex Overhead Cardioid Condencer Microphone
It is hard to believe that such small, unobtrusive microphones can produce such great sound,
but it's true. Available in black or white finishes, and with in line or plate mount preamps, the
Microflex? Overhead condenser microphones capture Shure quality sound in a compact, adjustable
package. Each model features a choice of interchangeable cardioid, supercardioid and omnidirectional
condenser microphone cartridges attached to a flexible, four inch gooseneck with a 30 foot cable.
The preamp options available offer easy installation in ceilings or microphone stands, and when combined
with the high sensitivity cartridge's wide frequency response, these microphones provide accurate sound
reproduction with a minimum of RF interference or electromagnetic hum.
Features:
Wide dynamic range and frequency response for accurate sound reproduction across the audio spectrum
Interchangeable cartridges that provide an optimal polar pattern choice for each application
Balanced, transformerless output for increased immunity to noise over long cable runs
Supplied stand-mount adapter for portable applications (in-line preamplifier versions only)
White or black finish that blends unobtrusively with most surroundings
Frequency Response
50 to 17,000 Hz
Output Impedance
180 ohms actual (EIA rated at 150 ohms)
Sensitivity (At 1,000 Hz, open circuit voltage*)
Cardioid: -35.0 dBV/Pa (17.8 mV)
Supercardioid: -33.5 dBV/Pa (21.1 mV)
Omnidirectional: -27.5 dBV/Pa (42.2 mV)
All values -12 dB at 0 gain; *1 Pascal = 94 dB SPL
Maximum SPL (1 kHz at 1% THD, 1 k ohm load)
Cardioid: 124.2 dB
Supercardioid: 122.7 dB
Omnidirectional: 116.7 dB
All values +6 dB at 0 gain
Equivalent Output Noise (A-weighted)
Cardioid: 28.0 dB SPL
Supercardioid: 26.5 dB SPL
Omnidirectional: 20.5 dB SPL
Signal to Noise Ratio (referenced at 94 dB SPL)
Cardioid: 66.0 dB
Supercardioid: 67.5 dB
Omnidirectional: 73.5 dB
Dynamic Range at 1 k ohm load
96.2 dB
100 dB at 0 gain
Common Mode Rejection
45.0 dB minimum
Preamplifier Output Clipping Level (1% THD)
-6.0 dBV (0.5 V)
-12 dBV at 0 gain
Polarity
Positive sound pressure on diaphragm produces positive voltage on pin 2 relative to pin 3 of output connector.
Power Requirements
11 to 52 Vdc phantom, 2.0 mA
Environmental Requirements
Operating Temperature Range: -18 to 57 degrees C (0 to 135 degrees F)
Relative Humidity: 0 to 95% |
The ME 65 is a super-cardioid microphone head designed for use with the K6 and K6P powering modules. It is especially suited to vocal and speech applications. Matt black, anodised, scratch-resistant finish.
- Pick-up pattern : super-cardioid
- Sensitivity in free field, no load (1kHz) : 10 mV/Pa +- 2,5 dB
- Nominal impedance : 200 Ohm (K6)
- Min. terminating impedance : 1000 Ohm (K6)
- Equivalent noise level : 20 dB
- Dimensions : d 44 x 131 mm
-
Weight :
|
The super-cardioid e 614 is a permantly polarized condenser microphone
designed for demanding applications which require a wide frequency response,
high SPL, fast transient response and a compact design. With its frequency
response of 40 Hz to 20 kHz, the e 614 is able to capture the full sound of the
instrument, while its super-cardioid pick-up pattern isolates the microphone
from other on-stage signals.
An excellent microphone for percussion instruments, the e 614 is also an ideal
choice for woodwind and string instruments. Its excellent acoustic properties
also make it a valuable tool for home recording.
Features
Rugged design Effective rejection of incidental rear noise Excellent directivity
across the whole frequency range Full, natural sound High maximum sound
pressure level
Wide frequency response
Delivery Includes
Microphone pouch
Microphone clip MZQ 100
Technical Data
Frequency response 40 Hz ... 20 kHz
Transducer principle permanently polarized condenser
Pick-up pattern supercardioid
Sensitivity in free field, no load (1kHz) 3 mV/Pa = - 50dB (0 dB = 1 V/Pa)
Nominal impedance 50 Ohm
Min. terminating impedance 1 kOhm
Maximum sound pressure level (passiv) 139 dB/SPL
Equivalent noise level 24 dB(A)
Equivalent noise level weighted as per CCIR 468-3 35 dB
Dimensions ? 20mm, L = 100mm
Weight w/o cable 93 g
|
8 Wide frequency response range
High sensitivity, Low distortion
High input withstand S.P.L.
Rugged brass case, Light weight
Shock mount adapters, stereo mounting bracket and wind screens as standard
PREMLIMINARY INFORMATION.
The MC10ST is a stereo microphone set including a pair of cardioid electret condenser microphones,
shock mount adapters, stereo mounting bracket and wind screens. The MC10ST can be used in a
wide range of applications, from studio and home recording to field or location sound aquisition.
Wide frequency response range
High sensitivity
Low distortion
High input withstand S.P.L.
Rugged brass case
Light weight
Shock mount adapters, stereo mounting bracket and wind screens as standard
Dedicated carry case as standard
SPECIFICATIONS:
Type: Back Electret Condenser Microphone
Polar Pattern: Cardioid
Frequency Response: 40Hz to 20kHz +/-10dB
Sensitivity: -40dBV/pa (10mv/pa)
Rated Impedance: 200ohm
Equivalent Noise Level: 22dB (A weighted IEC/DIN 651)
Maximum SPL: 134dB (THD |
Cardioid Condenser with 10dB Attenuator and 3 Position Low-Cut Filter
One of the world's great studio microphones, the SM81 provides precise, detailed sound reproduction, is excellent for studio recording, and is rugged enough for live sound reinforcement.
- A standard for acoustic instruments, including guitar and cymbals
- Selectable, low-frequency response -- either flat, 6dB/octave roll-off, or 18 dB/octave roll-off
- Built-in, switchable 10 dB attenuator for use in high SPL situations
- Phantom power only
- Windscreen included
- Low noise and high output clipping
- Cardioid condenser
- Frequency response: 20 to 20,000 Hz
| NT3 - Versatile & Dependable
Stylish and modern, the NT3 is a studio and location workhorse. With both
48V phantom and internal 9V battery operation, this R?DE is at home anywhere.
Intended for studio, stage and location work, this versatile handheld or stand
mounted microphone incorporates a true externally polarized condenser (hyper-
cardioid polar response) transducer with an internal capsule shock mounting
system, and an ultra-low noise electronic circuit that has a high immunity to R.F.
interference. Incorporating a rugged welded and heat-treated mesh head and all
metal body. The NT3 is supplied in a zip pouch with a windshield, stand mount
and thread adaptor.
SPECIFICATIONS:
Acoustic principle: Externally polarised 19mm (3/4“) condenser
Directional pattern: Hypercardioid
Frequency range: 20Hz-20 kHz
Output impedance: 200?
Signal noise ratio din iec 651: > 77dB (per IEC268-15)
Equvalent noise: 123dB (per IEC268-15)
Power supply voltage: P48, P24, P12 phantom 9V battery
Weight without battery: 371g
Weight with battery: 680g |
Reviews
There are no reviews yet.