Content |
The black Shure CVB-B/C is a Centraverse Series cardioid boundary condenser microphone designed to provide an optimized-for-speech frequency response and discreet desktop installation for presenters and speakers in conference rooms, corporate events, houses of worship, and meetings. The low-profile microphone features CommShield technology to reject RF interference and an attached 12’ XLR cable for compatibility with most mic preamps.
The cardioid condenser element yields a frequency response of 70 Hz to 16 kHz, which naturally attenuates low frequencies that are often produced by vibration and rumble. It is powered by 11 to 52 VDC phantom power.
- Cardioid polar pattern cartridge
- CommShield technology guards against RF interference from portable wireless devices (smartphones, among others) and enables high resistance to nearby radio signals
- Attached 12\' XLR cable
- Frequency response is suitable for capturing fast transients in a wide variety of locations such as podiums and desktops
- Shure design and rugged, dependable construction
- Mounting holes for secure installation
- CE compliant
General
Output Connectors |
1 x 3-Pin XLR |
Cable Length |
12.0\' / 3.66 m |
Operating Current Consumption |
2 mA |
Operating Voltage |
11 to 52 V |
Operating Temperature |
0 to 135°F / -17.78 to 57.22°C |
Operating Humidity |
0 to 95% |
Length |
3.5" / 88.90 mm |
Weight |
8 oz / 227 g |
Sound Field |
Mono |
Operating Principle |
Pressure Gradient |
Transducer |
Electret Condenser |
Tube |
No |
Polar Pattern |
Cardioid |
Frequency Range |
70 Hz to 16 kHz |
Signal-to-Noise Ratio |
67 dB |
Equivalent Noise Level |
27 dB A-Weighted |
Maximum SPL |
120 dB SPL |
THD |
1% |
Impedance |
180 Ohms |
Sensitivity |
23 mV/Pa |
Dynamic Range |
93 dB |
|
The half-cardioid e 901 is the perfect condenser microphone for kick drum. It is highly robust and step-resistant. It benefits from an integrated preamp.
Pick-up pattern : half-cardioid
Frequency response : 20...20 000 Hz
Sensitivity in free field, no load : (1kHz) 0,5 mV/Pa
Max. Sound pressure level (aktiv) : 154 dB / SPL
Phantom powering : 48 V / 1,1 mA
Nominal impedance :
Min. terminating impedance : 1000 Ohm
Dimensions : 126,5 x 105 x 26,5 mm
Weight : ca. 550 g
|
Condenser
Lightweight, sensitive diaphragm. Precisely and smoothly captures sound nuances. Powered by battery or phantom power supply.
Recommended Uses
Conference/Installed
Available Options
MX396C/DUAL Dual-Element 0-180 Degrees, Cardioid, back or bottom exit cable, mute output, LED input
MX396/TRI Dual-Element 90-0-90 mic, adjustable to 120-120-120 degrees, Cardioid, back or bottom exit cable, mute output, LED input
The Microflex® Multi-Element Boundary microphone delivers a unique and versatile tool for conference room installations.
Clean and simple in appearance, Multi-Element Boundary mics come in two or three element configurations, combining the coverage of multiple microphones into one small, compact package.
|
Offering outstanding Audio-Technica sound for surface-mount applications, the U851A features a PivotPoint® rotating output connector, UniSteep® filter and UniGuard® RFI-shielding technology. This battery- or phantom-powered condenser microphone accepts interchangeable condenser elements - available for boundary microphones in cardioid, hypercardioid and omnidirectional polar patterns. Its heavy die-cast case and silicon foam bottom pads minimize coupling of surface vibration to the microphone. With superior off-axis rejection and maximum gain-before-feedback, this professional microphone sets audio-quality standards in challenging acoustic environments.
- Designed for surface-mount applications such as high-quality sound reinforcement, professional recording, television, conferencing and other demanding sound pickup situations
- PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
- Superior off-axis rejection for maximum gain before feedback
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- UniSteep® filter provides a steep low-frequency attenuation to improve sound pickup without affecting voice quality
- Small-diameter UniPoint capsule near boundary eliminates phase distortion and delivers clear, high-output performance
- Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
- Low-profile design with low-reflectance black finish for minimum visibility
- Operates on battery or phantom power
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
- Frequency Response: 30-20,000 Hz
- Low Frequency Roll Off: 80 Hz, 18 dB/octave
- Open Circuit Sensitivity: Phantom: -40 dB (10.0 mV) re 1V at 1 Pa Battery: -41 dB (8.9 mV) re 1V at 1 Pa
- Impedance: Phantom: 200 ohms Battery: 270 ohms
- Maximum Input Sound Level: Phantom: 133 dB SPL, 1 kHz at 1% T.H.D. Battery: 123 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: Phantom: 111 dB,1 kHz at Max SPL Battery: 101 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 72 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 11-52V DC, 2 mA typical
- Battery Type: 1.5V AA/UM3
- Battery Current Life: 0.4 mA / 1200 hours typical (alkaline)
- Switch: Off, on-flat, on-roll-off
- Cable: 25.0' (7.6 m) long (permanently attached to microphone), 0.13" (3.2 mm) diameter, 2-conductor, shielded cable with TA3F-type connector
- Accessories: AT8531 power module; battery; soft protective pouch
|
Boundary-layer Microphone
The LD Systems BM1 is an electret condenser microphone with a hemispherical directional characteristic.
For micing upright and grand pianos on stage or in the studio. Additional applications in the area of conference technology, transmission of roundtable discussions and theatrical performances.
Product type
Microphones
Type
Installations
Frequency response
50 - 20000 Hz
Directivity
half ball
Nominal impedance
250 Ohm(s)
Max. SPL (1% THD @ 1kHz)
135 dB
Phantom power requierements
48 V
Microphone input
XLR (3-pin)
Width
27 mm
Height
74.5 mm
Diameter
93.5 mm
Accessories (included)
cables (Mini-XLR / XLR, 6 m)
Weight
0,345 kg
|
Condenser
Lightweight, sensitive diaphragm. Precisely and smoothly captures sound nuances. Powered by battery or phantom power supply.
Recommended Uses
Conference/Installed
Available Options
MX396C/DUAL Dual-Element 0-180 Degrees, Cardioid, back or bottom exit cable, mute output, LED input
MX396/TRI Dual-Element 90-0-90 mic, adjustable to 120-120-120 degrees, Cardioid, back or bottom exit cable, mute output, LED input
The Microflex® Multi-Element Boundary microphone delivers a unique and versatile tool for conference room installations.
Clean and simple in appearance, Multi-Element Boundary mics come in two or three element configurations, combining the coverage of multiple microphones into one small, compact package.
|
Reviews
There are no reviews yet.