Content |
Shure P4HW Wired Bodypack Personal Monitor
P4HW Wired Bodypack
Hardwired Bodypack
Key Features
Attached input cable
High-impact plastic chassis
Operating Controls:
Operating mode (Stereo, Mono, MixMode)
Volume knob
Balance knob
Defeatable limiter
High-frequency boost
-15 db Pad
Backlit LCD Indicators :
Battery life
Input level
Operating mode
Frequency Response
20 to 20,000 Hz
Total Harmonic Distortion
Channel Separation
35 dB (minimum)
Signal-to-noise ratio
85 dB (minimum)
Maximum Output Level
+5 dBu at 1% THD
Maximum Input Level
+7 dBu, input pad OFF
+22 dBu, input pad ON
Actual Input Impedance
> 40 kilohms
Audio Output Connector
3.5 mm stereo (left=tip, right=ring, ground=sleeve)
Power Requirements
9 V Alkaline battery
Battery Life
Up to 8 hours, volume dependant
Phantom Power Protection
Up to 60 VDC
|
Introducing the ES947LED, the new LED-equipped version of the Engineered Sound ES947 table-mount boundary microphone. The ES947LED features a touch-sensitive capacitive switch and LED status ring.
The cardioid condenser ES947/LED increases usability with a new toggle switch and LED status ring - which displays red when muted and green when switched on. The new LED-equipped version of the highly respected ES947 also features improved sensitivity and sound-to-noise ratio, perfectly suited to todayʼs digital matrix mixers.
The ES947/LED is available in black and white.
ES947LED Specifications 263 KB
| The Gravity MA 3D A lets you attach microphones, action cams and mobile phone holders to your microphone stand, and set them up flexibly. Its fastening mechanism is quick and easy to assemble. The large clamping range from 15 to 35 mm and the three joints' 360° rotation options allow you to install it as you like. Simply loosen, adjust and tighten the wing-screws.
Material: Plastic , Polyamide
Joint adjustment: Wing screw
Joint rotation: 360°
Joint tilt: 180°
Arm length: 400 mm
Suitable for mounting on: Microphone Stands
Suitable for tube diameter: 15 mm - 35 mm
Colour: Black
Thread size: 3/8”
Weight: 0,302 kg
|
The new AT8657/LED table-mount microphone adapter adds functionality to quick-mount gooseneck models from the Audio-Technicaʼs Engineered Sound, Unipoint and ProPoint installation mic ranges and ES945 and ES947 boundary microphone models.
The new AT8657/LED features a touch-sensitive capacitive switch surrounded by an illuminated LED status ring that can be set between red (mute) and green (on). Its integrated 3-pin XLR allows the table-mounting of gooseneck microphones with XLR connectors while the AT8657/LED has a 5-pin XLR out for audio and control data.
AT8657LED Specifications 270 KB
|
The RØDE invisiLav is designed to aid the concealing of the Lavalier and smartLav microphones.
Its soft construction absorbs noise and vibration, while the wide, flat profile provides coverage from the elements and allows for versatile mounting. There's two mounting points in case a redundant mic is required, and cable management on the side.
Available in either a pack of three or a bulk pack of ten, the invisiLav comes with pre-cut, skinsafe adhesive that can be used to stick the invisiLav to either the body or to fabric. The invisiLav itself is also made from a medical grade skin safe material so it can be mounted on the body without fear of irritation.
| Gravity MA 3D A POP 1 Traveler 3D Arm with Pop Filter
The Traveler Series' Pop Filter with 3D Arm
Every bit of weight counts when you're travelling by plane or truck from one gig to the next. After all, you can't always rely on the concert venue having the right tool available for you when needed.
The Pop Filter with 3D Arm MA 3D A POP 1 can be taken everywhere you go. It's so light and space-saving, there's absolutely no need for you to worry about weight or storage space.
With this tool you can enhance your voice- and vocal recordings by placing the high-quality pop filter, with double nylon mesh and a large screen diameter of 15.7 cm between you and your microphone. This way you avoid unwanted pop noises and clipping.
Its fastening mechanism is quick and easy to assemble. The large clamping range from 15 to 35 mm lets you mount it on all popular microphone stands, and the three joints' 360° rotation options allow you to install it as you like. Simply loosen, adjust and tighten the wing-screws. Voila - you're all done! Once set, the MA 3D A POP 1 stays locked in place.
Gravity® has once again delivered a small, useful and reliable product for you to round off your collection of stands.
Product type |
Microphone Accessories |
Type |
Pop filter |
Material |
Plastic, Polyamide |
Color |
Black |
Joint adjustment |
Wing screw |
Joint rotation |
360° |
Joint tilt |
180° |
Arm length |
400 mm |
Suitable for mounting on |
Microphone Stands |
Thread size |
3/8” |
Screen diameter |
157 mm |
Setup |
Double nylon screen, plastic frame |
Suitable for tube diameter |
15 - 35 mm |
Weight |
0,377 kg |
|
Reviews
There are no reviews yet.