Content |
The SLX1 bodypack transmitter is designed to hold up to the most adverse conditions. Whether used with headworn, lavalier, instrument microphones, or with guitars or basses, the SLX1 is the definition of reliability.
The SLX1 bodypack transmitter is designed to hold up to the most adverse conditions. Whether used with headworn, lavalier, instrument microphones, or with guitars or basses, the SLX1 is the definition of reliability.
- Automatic Transmitter Setup
- Backlit LCD with timeout feature
- Frequency and power lockout
- 3-segment battery fuel gauge
- 2 AA batteries (included) provide 8 hours of continuous use
- 518 - 782 MHz operating range
Audio Input Level
-10 dBV maximum at mic gain position
+10 dBV maximum at 0 dB gain position
+20 dBV maximum at -10 dB gain position
Gain Adjustment Range
30dB
Input Impedance
1 MΩ
RF Transmitter Output
30 mW maximum (dependent on applicable country regulations)
Dimensions
108 mm H x 64 mm W x 19 mm D (4.25 x 2.50 x 0.75 in.)
Weight
81 grams (3 oz.) without batteries
Housing
Molded ABS case
Power Requirements
2 "AA” size alkaline or rechargeable batteries
Battery Life
>8 hours (alkaline)
|
Product type
Wireless Microphone System Accessories
Type
Belt Packs
Transmission frequency range
863.000 - 865,000 MHz
Channels
16
Inputs
Mini-XLR (3-pin) with phantom power (for headset)
Frequency response
60 - 16.000 Hz
Rated HF output power
10
Controls
ASC , Mic / 0dB / -10 dB switch , Power
Indicators
power/battery status low (LED)
Operating voltage
2 x AA battery
Operating time
>10 h (with alkaline batteries)
Width
65 mm
Height
85 mm
Depth
24 mm
Weight
0,1 kg
Other features
incl. batteries , IR frequency synchronisation
|
The IR-200M is a handheld infrared wireless microphone. It eliminates problems with interference or eavesdropping, allowing simultaneous use in adjacent conference rooms or school classrooms. Since infrared wireless microphone system uses a frequency band that does not interfere with that of the TS-800 and TS-900 series infrared conference system, both systems can be simultaneously installed in the same location.
Battery | IR-200BT-2 rechargeable battery for the infrared wireless microphone (option)
or AA alkaline dry cell battery (2 pieces). | Current Consumption | Typ. 250 mA (2.4 V, Power selector switch: N)
Typ. 340 mA (2.4 V, Power selector switch: H) |
Infrared Emitter
Wavelength | 870 nm (AM: Brightness modulation) | Modulation Method | Frequency modulation | Carrier Frequency | Channel A: 3.100 MHz
Channel B: 3.350 MHz | Transmission Distance | Approx. 20 m (65 ft) (Power selector switch: H, in an unobstructed space)
Approx. 15 m (50 ft) (Power selector switch: N, in an unobstructed space) | Tone Signal | 32.768 kHz | Modulation Sensitivity | ±4.8 kHz (1 kHz, when SPL of 84 dB is input) | Maximum Input Sound Pressure | 120 dB SPL | Microphone Unit | Unidirectional electret condenser microphone | Frequency Response | 100 Hz - 12 kHz | Preemphasis | 300 μs | Battery Operation Time | Approx. 8 h (when the IR-200BT rechargeable battery for the infrared wireless
microphone is used, Power selector switch: N)
Approx. 6 h (when the alkaline battery is used, Power selector switch: N) | Operating Temperature | 0 ℃ to +40 ℃ (32 ゜F to 104 ゜F) | Operating Humidity | 30 % to 85 %RH | Finish | Control section: ABS resin, metallic gray, paint, 50% gloss
Filter section: Polycarbonate, optical cut filter | Dimensions | φ37 × 241.8 (H) mm (φ1.46" × 9.52“) | Weight | 170 g (0.37 lb) (with battery) | Accessory | Screw driver (for setting) …1, Color label (6 colors) …1 |
|
The WM-5320 lavalier wireless microphone has been manufactured for use with a UHF system. It employs an omni-directional electret condenser microphone element and has been designed for use in speech reinforcement applications. The built-in compressor-expander circuit minimizes the influence from ambient noise.
Microphone Element | Electret condenser microphone, omni-directional pattern | Modulation | Frequency modulation | Frequency Range | 636 - 865 MHz*, UHF | Channel Selectable | 64 channels
(the number of channels may differ from country to country) | RF Carrier Power | 50 mW or less | Tone Frequency | 32.768 kHz | Oscillator | PLL synthesized | Maximum Input Level | 110 dB SPL (Audio level control: Maximum position) | Battery | LR6 (AA) | Battery Life | 10 hours or more (alkaline) | Indicator | Power/Battery lamps | Antenna | Built-in type | Operating Temperature | -10℃ to +50℃ | Finish | Resin, coating | Dimensions | 62 (W) × 102.5 (H) × 23 (D) mm | Weight | 110 g (with battery) | Accessory | Screw driver ……1, Storage case ……1, Neck strap ……1 |
|
Modulation
FM (45 kHz max. deviation)
Frequency Range
470–952 MHz (depending on region)
Tuning Bandwidth
Up to 80 MHz (depending on region)
Antenna
Dipole, UR3 housing and attached microphone form the antenna
Carrier Frequencies
Up to 3200, tunable in steps of 25 kHz (depending on region)
RF Power Output
Selectable 10 mW or 50 mW maximum, depending on region
Power Requirements
Two (2) 1.5V AA alkaline
Battery Life
10 Hours (alkaline) with no phantom power @ 10 mW, typical (frequency band dependent)
4 Hours (alkaline), with 48 V phantom power @ 50 mW, typical (frequency band dependent)
Gain Adjustment Range
-10 to +20 dB, MIC or LINE input setting
Pilot Tone
32 kHz
Frequency Stability
± 0.0015%
Spurious Radiation
75 dB below carrier (typical)
Equivalent Input Noise
-127.0 dBV, A-weighted (audio front end)
Maximum Audio Input level
+24 dBV (LINE input, 0 dB gain)
-21 dBV (MIC input, 0 dB gain)
Differential Input Impedance
6 kΩ LINE input setting
3 kΩ MIC input setting
System Frequency Response
35 Hz–17 kHz, (+1.5 dB, -3 dB)
Note: Overall system frequency response depends on the microphone element and receiver.
High Pass Filter
Two-pole (12 dB per octave), selectable cut off frequency from 40 Hz to 240 Hz
System THD+N
|
Shure SLX2-BETA87C-R5 Wireless Microphone
Features:
Automatic Transmitter Setup
Backlit LCD with timeout feature
Frequency and power lockout
3-segment battery fuel gauge
2 AA batteries (included) provide 8 hours of continuous use
518 - 782 MHz operating range
Operating Range Under Typical Conditions
100m (300 ft.)
Note: actual range depends on RF signal absorption, reflection, and
interference
Audio Frequency Response (+/? 2 dB)
Minimum: 45 Hz
Maximum: 15 kHz
(Overall system frequency depends on microphone element.)
Total Harmonic Distortion (ref. +/? 38 kHz deviation, 1 kHz tone)
0.5%, typical
Dynamic Range
>100 dB A-weighted
Operating Temperature Range
?18°C (0°F) to +50°C (+122°F)
Note: battery characteristics may limit this range
Transmitter Audio Polarity
Positive pressure on microphone diaphragm (or positive voltage applied
to tip of WA302 phone plug) produces positive voltage on pin 2 (with
respect to pin 3 of low impedance output) and the tip of the high
impedance 1/4-inch output.
SLX1 Bodypack Transmitter
Audio Input Level
-10 dBV maximum at mic gain position
+10 dBV maximum at 0 dB gain position
+20 dBV maximum at -10 dB gain position
Gain Adjustment Range
30dB
Input Impedance
1 MΩ
RF Transmitter Output
30 mW maximum (dependent on applicable country regulations)
Dimensions
108 mm H x 64 mm W x 19 mm D (4.25 x 2.50 x 0.75 in.)
Weight
81 grams (3 oz.) without batteries
Housing
Molded ABS case
Power Requirements
2 ?AA? size alkaline or rechargeable batteries
Battery Life
>8 hours (alkaline)
SLX2 Handheld Transmitter
Audio Input Level
+2 dBV maximum at -10dB position
-8 dBV maximum at 0dB position
Gain Adjustment Range
10dB
RF Transmitter Output
30 mW maximum (dependent on applicable country regulations)
Dimensions (including SM58 cartridge)
254 mm x 51 mm dia. (10 x 2 in.)
Weight
290 grams (10.2 oz.) without batteries
Housing
Molded PC/ABS handle and battery cup
Power Requirements
2 ?AA? size alkaline or rechargeable batteries
Battery Life
>8 hours (alkaline)
SLX4 Receiver
Dimensions
42 mm H x 197 mm W x 134 mm D (1.65 x 7.76 x 5.28 in.)
Weight
816 g (1 lb. 13 oz.)
Housing
Galvanized steel
Audio Output Level (ref. +/? 38 kHz deviation with 1 kHz tone)
XLR connector (into 600 Ω load): ?13 dBV
1/4 inch connector (into 3000 Ω load): ?2 dBV
Output Impedance
XLR connector: 200 Ω
1/4 inch connector: 1kΩ
XLR output
Impedance balanced
Pin 1: Ground
Pin 2: (+)
Pin 3: (-)
Sensitivity
?105 dBm for 12 dB SINAD, typical
Image Rejection
>70 dB, typical
Power Requirements
12?18 Vdc at 150 mA, supplied by external power supply
|
Reviews
There are no reviews yet.